To cover requirements for boxes and enclosures with provision for suspension means

  • Amendment
    16 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    15 pages
    English language
    sale 10% off
    e-Library read for
    1 day

IEC 61535:2023 is available as IEC 61535:2023 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.
IEC 61535:2023 applies to two-wire, up to five-wire installation couplers, with or without earthing contact, if provided, with a rated voltage up to and including 500 V AC or 500 V DC and a rated connecting capacity up to and including 10 mm2 and a rated current not exceeding 32 A for permanent connection in electrical installations. Installation couplers with additional contacts for voltages other than mains voltages are outside the scope of this document. This third edition cancels and replaces the second edition published in 2019. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition:
a) inclusion of a definition for "live part" based on IEC 61140;
b) additional optional cross medial documentation, e.g. marking with QR-Code;
c) corrections on the consistent use of the expressions "earth", "earthing contact", "earthing circuit" and "protective earth(ing)" throughout the document;
d) addition of missing compliance provisions to 13.3;
e) update of Figure D.1 of Annex D;
f) inclusion of new Annex F for cold climate requirements.

  • Standard
    179 pages
    English language
    sale 15% off

IEC 62275:2018 specifies requirements for metallic, non-metallic and composite cable ties and their associated fixing devices used for the management and support of wiring systems in electrical installations. This third edition cancels and replaces the second edition published in 2013. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: a) consideration of adhesive fixing devices, b) revised and updated normative references, c) modified definitions for metallic and composite cable ties, d) new definitions, e) improvement of test procedures, f) new figures for typical arrangement of test assembly for fixing devices and for integral fixing devices.

  • Standard
    45 pages
    English language
    sale 10% off
    e-Library read for
    1 day

IEC 62275:2022 specifies requirements for metallic, non-metallic and composite cable ties and their associated fixing devices as a means used for managing or securing the wiring systems in electrical installations. Cable ties and associated fixing devices can also be suitable for other applications, such as support of wiring systems, and where so used, additional requirements can apply. This fourth edition cancels and replaces the third edition published in 2018. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition:
- scope clarification,
- new definitions,
- deletion of the exception for the stabilization of the moisture content,
- possibility to carry out tensile strength tests with dead weights,
- differentiation of rubber and acrylic adhesive fixings,
- clarification for mechanical testing of integral devices,
- clarifications on Table 6,
- clarifications in 9.1,
- the minimum installation temperature test for cable ties is carried out only when the declared minimum temperature is lower than 0 °C,
- a requirement that metallic cable ties be classified according to 6.2.3,
- definition of colours to be tested for contribution to fire,
- addition of a "some countries" note in Clause 10,
- clarification of the mounting of fixing devices in the resistance to ultraviolet light test,
- clarification on the testing of integral devices in the resistance to ultraviolet light test.

  • Standard
    83 pages
    English and French language
    sale 15% off

IEC TR 63044-2:2022(E) provides the environmental conditions for HBES/BACS devices, when declared in the manufacturer's documentation for use in one or more of the environment classes as defined in Clause 6 of this document.

  • Technical report
    17 pages
    English language
    sale 15% off

IEC 60947-4-1:2018 is available as IEC 60947-4-1:2018 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.IEC 60947-4-1:2018 is applicable to the following equipment: - electromechanical contactors and starters including motor protective switching device (MPSD); - actuators of contactor relays; - contacts dedicated exclusively to the coil circuit of this contactor or this contactor relay; - dedicated accessories (e.g. dedicated wiring, dedicated latch accessory); intended to be connected to distribution circuits, motors circuits and other load circuits, the rated voltage of which does not exceed 1 000 V AC or 1 500 V DC. This fourth edition cancels and replaces the third edition published in 2009 and its Amendment 1:2012. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: - Scope structure and exclusions - Editorial correction of notes and hanging paragraphs - Reference to IEC 62683-1 - Motor protective switching device (MPSD) with its requirements - Safety aspects related to: - General aspects; - Limited energy circuits; - Electronic circuits; - Assessment procedure for electromechanical overload protection used in safety -applications (new Annex L) - Introduction of provisions covering the impact of higher locked rotor current to achieve high efficiency class - Mention of dedicated wiring accessories - Pickup power measurement - Alignment to IEC 60947-1:2007, IEC 60947-1:2007/AMD1:2010, and IEC 60947‑1:2007/AMD2:2014 - Direct current requirements for covering photovoltaic application (new Annex M) - Load monitoring indicators (new Annex O) - Short-circuit breaking tests of MPSD (new Annex P) - Co-ordination under short-circuit conditions between a MPSD and another short-circuit protective device associated in the same circuit (new Annex Q).

  • Standard
    187 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Standard
    187 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This International Standard specifies requirements and tests for cable cleats used for securing cables in electrical installations and for intermediate restraints used for holding cables together in formation in electrical installations. Cable cleats provide resistance to electromechanical forces where declared. This standard includes cable cleats that rely on a mounting surface specified by the manufacturer for axial and/or lateral retention of cables.
NOTE Requirements for manufacturers in this document also apply to importers and responsible vendors where appropriate.
This standard does not apply to cable ties.

  • Standard
    45 pages
    English language
    sale 10% off
    e-Library read for
    1 day

IEC 60358-4:2018 applies to DC or AC single-phase capacitor-dividers connected between line and ground used for manufacturing Voltage Transformers as well as for other applications. IEC 60358-4:2018 is to be used in conjunction with the latest edition of IEC 60358-1 and its amendments. IEC 60358-4:2018 was established on the basis of the IEC 60358-1:2012. IEC 60358-4:2018 supplements or modifies the corresponding clauses in IEC 60358-1:2012. This standard cancels and replaces the second edition of IEC 60358 (1990), and constitutes a technical revision.

  • Standard
    16 pages
    English language
    sale 10% off
    e-Library read for
    1 day

IEC TR 63396:2021(E) documents a method for the sound pressure level measurement on power capacitor units, by which the sound power level of power capacitor units is determined.
This method is applicable to shunt capacitor units and AC filter capacitor units for AC power systems with a nominal voltage of 1 kV and above and a frequency of 50 Hz or 60 Hz.
This method also applies to the DC filter capacitor units.
Other measurements on power capacitor units can be implemented with reference to this method.

  • Technical report
    22 pages
    English language
    sale 15% off

This document applies to cable reels provided with a non-detachable flexible cable with a
rated operating voltage not exceeding 690 V DC and/or 690 V AC with a frequency not
exceeding 500 Hz and a rated current not exceeding 63 A, primarily intended for industrial
use, either indoors or outdoors, for use with accessories complying with IEC 60309-1,
IEC 60309-2 or IEC 60309-4.
This document applies to:
– portable cable reels equipped with one plug or appliance-inlet complying with IEC 60309-1
or IEC 60309-2 and at least one socket-outlet complying with IEC 60309-1, IEC 60309-2
or IEC 60309-4;
– fixed cable reels equipped with at least one socket-outlet complying with IEC 60309-1,
IEC 60309-2 or IEC 60309-4;
– cable reels suitable for use at ambient temperature normally within the range of −25 °C
to +40 °C.
The use of this equipment on construction sites and for agricultural, commercial and domestic
appliances is not precluded.
This document also applies to cable reels intended to be used in extra-low voltage
installations.
In locations where special conditions prevail, for example, on board ships, in vehicles and the
like, or where explosions are liable to occur, additional requirements can be necessary.
NOTE 1 This document was not developed for Electric Vehicle (EV) application, but it can be used as guide for
cable reels for EV application
NOTE 2 Additional requirements for cable reels for currents higher than 63 A are under consideration.

  • Standard
    59 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    53 pages
    English language
    sale 10% off
    e-Library read for
    1 day

To be launched for vote and published with prEN IEC=66754.

  • Amendment
    11 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    10 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This part of IEC 60670 applies to boxes, enclosures and parts of enclosures (hereafter called
“boxes” and “enclosures”) for electrical accessories with a rated voltage not exceeding
1 000 V a.c. and 1 500 V d.c. intended for household or similar fixed electrical installations,
either indoors or outdoors.
Boxes and enclosures complying with this standard are suitable for use at ambient
temperatures not normally exceeding +40 °C, but their average over a period of 24 h does not
exceed +35 °C, with a lower limit of the ambient air temperature of −5 °C.
During the installation the temperature may be outside the above temperature range
according to the classification of the boxes and the enclosures.
This International Standard is intended to apply to boxes and enclosures for electrical
accessories within the scope of IEC technical committee 23.
This standard may be used as a reference document for other IEC technical committees and
subcommittees.
A box or an enclosure which is an integral part of an electrical accessory and provides
protection for that accessory against external influences (for example mechanical impact,
ingress of solid objects or water, etc.) is covered by the relevant standard for such an
accessory.
This standard does not apply to
– ceiling roses;
– luminaire supporting couplers;
– boxes, enclosures and parts of enclosures specifically designed to be used for cable
trunking and ducting systems complying with IEC 61084 and which are not intended to be
installed outside of these systems.

  • Standard
    67 pages
    English language
    sale 10% off
    e-Library read for
    1 day

IEC 61316:2021 is available as IEC 61316:2021 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.IEC 61316:2021 applies to cable reels provided with a non-detachable flexible cable with a rated operating voltage not exceeding 690 V DC and/or 690 V AC with a frequency not exceeding 500 Hz and a rated current not exceeding 63 A, primarily intended for industrial use, either indoors or outdoors, for use with accessories complying with IEC 60309-1, IEC 60309-2 or IEC 60309-4. This third edition cancels and replaces the second edition, published in 1999. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: - Implementation of the latest tests and requirements previously included in IEC 60309-1.

  • Standard
    59 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    53 pages
    English language
    sale 10% off
    e-Library read for
    1 day

IEC 63044-6:2021 specifies the requirements for planning and installation of HBES/BACS and the supporting infrastructure. Radio frequency (RF) HBES/BACS are also considered. Safety requirements are covered by IEC 60364 (all parts). Information and communication technology (ICT) and broadcasting and communication technology (BCT) network installations are typically interfaced with HBES/BACS. The requirements for ICT and BCT network installations are covered by ISO/IEC 14763-2. This document does not cover HBES/BACS implementation with: - optical fibre, - power lines, - power over Ethernet (PoE).

  • Standard
    43 pages
    English language
    sale 10% off
    e-Library read for
    1 day

IEC 63044-4:2021 provides the functional safety requirements for HBES/BACS. In addition, it defines functional safety requirements for the interface of equipment intended to be connected to an HBES/BACS network. It does not apply to interfaces to other networks. This document does not provide functional safety requirements for safety-related systems. This document does not provide requirements on data protection and security.

  • Standard
    32 pages
    English language
    sale 10% off
    e-Library read for
    1 day

IEC 61316:2021 is available as IEC 61316:2021 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.
IEC 61316:2021 applies to cable reels provided with a non-detachable flexible cable with a rated operating voltage not exceeding 690 V DC and/or 690 V AC with a frequency not exceeding 500 Hz and a rated current not exceeding 63 A, primarily intended for industrial use, either indoors or outdoors, for use with accessories complying with IEC 60309-1, IEC 60309-2 or IEC 60309-4. This third edition cancels and replaces the second edition, published in 1999. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition:
- Implementation of the latest tests and requirements previously included in IEC 60309-1.

  • Standard
    113 pages
    English and French language
    sale 15% off

IEC 63044-6:2021 specifies the requirements for planning and installation of HBES/BACS and the supporting infrastructure.
Radio frequency (RF) HBES/BACS are also considered.
Safety requirements are covered by IEC 60364 (all parts).
Information and communication technology (ICT) and broadcasting and communication technology (BCT) network installations are typically interfaced with HBES/BACS.
The requirements for ICT and BCT network installations are covered by ISO/IEC 14763-2.
This document does not cover HBES/BACS implementation with:
- optical fibre,
- power lines,
- power over Ethernet (PoE).

  • Standard
    78 pages
    English and French language
    sale 15% off

IEC 63044-4:2021 provides the functional safety requirements for HBES/BACS.
In addition, it defines functional safety requirements for the interface of equipment intended to be connected to an HBES/BACS network. It does not apply to interfaces to other networks.
This document does not provide functional safety requirements for safety-related systems.
This document does not provide requirements on data protection and security.

  • Standard
    62 pages
    English and French language
    sale 15% off

his document is applicable to both self-healing capacitor units and self-healing capacitor banks intended to be used, particularly, for power-factor correction of AC power systems having a rated voltage above 1 000 V and fundamental frequencies of 15 Hz to 60 Hz. The following capacitors are excluded from this document: - shunt power capacitors of the self-healing type for AC systems having a rated voltage up to and including 1 000 V (IEC 60831-1, -2); - shunt power capacitors of the non-self-healing type for AC systems having a rated voltage up to and including 1 000 V (IEC 60931-1, -2 and -3); - shunt capacitors of the non-self-healing type for AC power systems having a rated voltage above 1 000 V (IEC 60871-1, -2, -3 and -4); - capacitors for inductive heat-generating plants operating at frequencies between 40 Hz and 24 000 Hz (IEC 60110-1 and -2); - series capacitors (IEC 60143-1, -2, -3 and -4); - AC motor capacitors (IEC 60252-1 and -2); - coupling capacitors and capacitor dividers (IEC 60358-1, -2, -3, -4); - capacitors for power electronic circuits (IEC 61071); - small AC capacitors to be used for fluorescent and discharge lamps (IEC 61048 and IEC 61049); - capacitors for suppression of radio interference; - capacitors intended to be used in various types of electrical equipment, and thus considered as components; - capacitors intended for use with DC voltage superimposed on the AC voltage. Requirements for accessories such as insulators, switches, instrument transformers and external fuses are given in the relevant IEC standards and are not covered by the scope of this document. The object of this document is to: a) formulate uniform rules regarding performances, testing and rating; b) formulate specific safety rules; c) provide a guide for installation and operation.

  • Standard
    59 pages
    English language
    sale 10% off
    e-Library read for
    1 day

IEC 63210:2021 is applicable to both self-healing capacitor units and self-healing capacitor banks intended to be used, particularly, for power-factor correction of AC power systems having a rated voltage above 1 000 V and fundamental frequencies of 15 Hz to 60 Hz.
The following capacitors are excluded from this document:
- shunt power capacitors of the self-healing type for AC systems having a rated voltage up to and including 1 000 V (IEC 60831-1, -2);
- shunt power capacitors of the non-self-healing type for AC systems having a rated voltage up to and including 1 000 V (IEC 60931-1, -2 and -3);
- shunt capacitors of the non-self-healing type for AC power systems having a rated voltage above 1 000 V (IEC 60871-1, -2, -3 and -4);
- capacitors for inductive heat-generating plants operating at frequencies between 40 Hz and 24 000 Hz (IEC 60110-1 and -2);
- series capacitors (IEC 60143-1, -2, -3 and -4);
- AC motor capacitors (IEC 60252-1 and -2);
- coupling capacitors and capacitor dividers (IEC 60358-1, -2, -3, -4);
- capacitors for power electronic circuits (IEC 61071);
- small AC capacitors to be used for fluorescent and discharge lamps (IEC 61048 and IEC 61049);
- capacitors for suppression of radio interference;
- capacitors intended to be used in various types of electrical equipment, and thus considered as components;
- capacitors intended for use with DC voltage superimposed on the AC voltage.
Requirements for accessories such as insulators, switches, instrument transformers and external fuses are given in the relevant IEC standards and are not covered by the scope of this document.
The object of this document is to:
a) formulate uniform rules regarding performances, testing and rating;
b) formulate specific safety rules;
c) provide a guide for installation and operation.

  • Standard
    115 pages
    English and French language
    sale 15% off

IEC 63044-3:2017 provides the electrical safety requirements related to the HBES/BACS network in addition to the product safety standards for HBES/BACS devices. It also applies to devices used within an HBES/BACS network for which no specific HBES/BACS product safety standard exists. In addition, it defines safety requirements for the interface of equipment intended to be connected to an HBES/BACS network. It does not apply to interfaces to other networks. NOTE An example of other networks is a dedicated ICT network covered by IEC 62949. This document is applicable to   operator stations and other human–system interface devices,  devices for management functions,  control devices, automation stations and application-specific controllers,  field devices and their interfaces, and  cabling and interconnection of devices  used within a dedicated HBES/BACS network. This document covers the following requirements and compliance criteria:   protection from hazards in the device;  protection from overvoltages on the network;  protection from touch current;  protection from hazards caused by different types of circuit;  protection of the communication wiring from overheating caused by excessive current.  Key words: Home automation, smart homes, smart cities

  • Standard
    22 pages
    English language
    sale 10% off
    e-Library read for
    1 day

2020-11-24: EC formal rejection for citation under EMCD
2020-10-02 because of formal EC rejection for citation under LVD, also the AC is unchecked from LVD
TAN - // IEC Corrigendum

  • Corrigendum
    3 pages
    English and French language
    sale 10% off
    e-Library read for
    1 day

The purpose of this document is to provide requirements for equipment to be used in energy
efficiency systems. This document covers load-shedding equipment (LSE).
Guidelines relating to safety for LSE as given in IEC Guide 110 have been followed.
This document applies to load-shedding equipment for household and similar uses. The loadshedding
function is used in energy management systems to optimize the overall use of
electrical energy including production and storage. Load-shedding can be used for example
for energy efficiency purposes as per IEC 60364-8-1:2019.
This document applies to LSE for operation under normal conditions:
– AC circuits with a rated frequency of 50 Hz, 60 Hz or both, with a rated voltage not
exceeding 440 V (between phases), a rated current not exceeding 125 A and a rated
short-circuit capacity not exceeding 25 000 A; or
– DC circuits1.
LSEs are intended to control the energy supplied to one or more load, circuit or mesh when:
– defined conditions of time and current are reached;
– a command or information from an external system is received.
An LSE is intended to serve as:
– a single equipment having all the necessary means able to control the loads (e.g. the
electrical energy management function is embedded in such an equipment); or
– a unit integrated into a more complex equipment or an independent equipment being part
of an electrical energy management system (EEMS); or
– an assembly of independent equipment forming an LSE (e.g. an LSE with external current
sensors); or
– as a combination of the above points.
LSE can have a wireless interface.
LSE is part of the fixed installation.
NOTE 1 This document covers load shedding equipment in the fixed installations including portable appliances
connected thereto.
LSE are intended for use in circuits with protection against electrical shock and over-current
according to IEC 60364 (all parts).
NOTE 2 For example, fault protection (indirect contact protection) can be covered as follows:
– in TT systems, by an upstream RCBOs or RCCBs according to IEC 61008-1 and IEC 61009-1;
– in a TN system, by an upstream over-current protective device.
LSEs do not, by their nature, provide an isolation function nor the over-current protection.
LSEs are normally installed by instructed persons (IEC 60050-195:1998, 195-04-02) or skilled
persons (IEC 60050-195:1998, 195-04-01) and normally used by ordinary persons
(IEC 60005-195:1998, 195-04-03).
This document contains all requirements necessary to ensure compliance with the operational
characteristics required by type tests for LSEs based on single equipment or based on an
assembly of independent equipment.
These requirements apply for standard conditions of temperature and environment as given
in 5.1. They are applicable to LSEs with a degree of protection of IP 20 intended for use in an
environment with pollution degree 2. For LSE having a degree of protection higher than IP 20
according to IEC 60529, for use in locations where arduous environmental conditions prevail
(e.g. excessive humidity, heat or cold or deposition of dust) and in hazardous locations (e.g.
where explosions are liable of occur), special construction can be required.
If other functions are included in LSE, these functions are covered by the relevant standards.
This document does not address communication aspects such as protocols, interoperability,
data security and any other related aspects.

  • Standard
    136 pages
    English language
    sale 10% off
    e-Library read for
    1 day

2017-05-02: D156/C084 - Ratified standards not being made available.
DOP = DAV + 6 months
DOW = DAV + 36 months
Annex ZZ for MD 2006/42/EC available in EN 60947-5-5:1997/A11.

  • Amendment
    18 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This standard specifies requirements for metallic, non-metallic and composite cable ties and their associated fixing devices used for the management and support of wiring systems in electrical installations. Cable ties and associated fixing devices can also be suitable for other applications and where so used, additional requirements can apply. This document does not contain requirements that evaluate any electrical insulation properties of the cable tie or mechanical protection of the cables provided by the cable tie. This document contains requirements for the mechanical interface of an adhesive fixing device to a solid surface. It does not consider the mechanical behaviour of the solid surface in itself. This document does not consider the mechanical interface, for example the mounting screw, of a fixing device other than adhesive to a solid surface.

  • Standard
    45 pages
    English language
    sale 10% off
    e-Library read for
    1 day

IEC 63044-5-1:2017 is a product family standard that sets the minimum level of EMC performance for the HBES/BACS network in addition to the product EMC standards for HBES/BACS devices. It also applies to devices used within an HBES/BACS network for which no specific HBES/BACS product EMC standard exists. In addition, it defines EMC requirements for the interface of equipment intended to be connected to an HBES/BACS network. It does not apply to interfaces to other networks. NOTE An example of other networks is a dedicated ICT network covered by CISPR 22 and 23. This document provides general performance requirements and test set-ups. This document is applicable (but not limited) to   operator stations and other human–system interface devices,  devices for management functions,  control devices, automation stations and application-specific controllers,  field devices and their interfaces,  cabling and interconnection of devices,  used within a dedicated HBES/BACS network.

  • Standard
    24 pages
    English language
    sale 10% off
    e-Library read for
    1 day

IEC 63044-5-3:2017 is a product family standard that sets the minimum level of EMC performance for the HBES/BACS network in addition to the product EMC standards for HBES/BACS devices. It also applies to devices used within an HBES/BACS network for which no specific HBES/BACS product EMC standard exists. In addition, it defines EMC requirements for the interface of equipment intended to be connected to an HBES/BACS network. It does not apply to interfaces to other networks. NOTE An example of other networks is a dedicated ICT network covered by CISPR 22 and 23. This document specifies EMC requirements for HBES/BACS to be installed in industrial environments, according to the definition given in IEC 61000-6-2. NOTE Industrial environment covers the office spaces that may be present in industrial premises. Industrial automation systems are outside the scope. This document is applicable (but not limited) to   operator stations and other human–system interface devices,  devices for management functions,  control devices, automation stations and application-specific controllers,  field devices and their interfaces,  cabling and interconnection of devices,  used within a dedicated HBES/BACS network. This publication is to be read in conjunction with IEC 63044-5-1:2017.

  • Standard
    11 pages
    English language
    sale 10% off
    e-Library read for
    1 day

IEC 61535:2019 is available as IEC 61535:2019 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.
IEC 61535:2019 applies to two-wire, up to five-wire installation couplers, including earth, if provided, with a rated voltage up to and including 500 V AC or DC and a rated connecting capacity up to and including 10 mm2 for permanent connection in electrical installations. Installation couplers with additional contacts for voltages other than mains voltages are outside the scope of this document. This second edition cancels and replaces the first edition published in 2009 and Amendment 1:2012. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition:
- enlargement of the scope to DC application;
- addition of further requirements as regards DC application (marking, etc.), no additional test procedures were deemed necessary; however some modifications were necessary in the normative text;
- changes and enhancement of the field of application of installation couplers into outdoor applications;
- addition of a suitable temperature range;
- updating of the list of normative references, modified to undated references, where possible.

  • Standard
    106 pages
    English and French language
    sale 15% off

This European standard specifies the required characteristics, test methods, qualification and production
routine testing of heat shrinkable moulded shapes.

  • Standard
    10 pages
    English language
    sale 10% off
    e-Library read for
    1 day

IEC TS 60904-1-2:2019 describes procedures for the measurement of the current-voltage (I-V) characteristics of bifacial photovoltaic devices in natural or simulated sunlight. It is applicable to single PV cells, sub-assemblies of such cells or entire PV modules.
This document may be applicable to PV devices designed for use under concentrated irradiation if they are measured without the optics for concentration, and irradiated using direct normal irradiance and a mismatch correction with respect to a direct normal reference spectrum is performed. This document describes the additional requirements for the measurement of I-V characteristics of bifacial PV devices.

  • Technical specification
    18 pages
    English language
    sale 15% off

IEC 62047-32:2019 specifies the test method and test condition for the nonlinear vibration of MEMS resonators. The statements made in this document apply to the development and manufacture for MEMS resonators.

  • Standard
    37 pages
    English and French language
    sale 15% off

IEC 60076-22-2:2019 applies to radiators mounted on liquid immersed power transformers according to IEC 60076-1 and reactors according to IEC 60076-6 with and without conservator for indoor or outdoor installation. It outlines the service conditions and the mechanical and electrical requirements that are common to this equipment. It also outlines the operation requirements specific to this equipment as well as the preferred dimensions relevant for interchangeability and the type and routine tests to be performed.
Keywords: radiators mounted on liquid immersed power transformers

  • Standard
    56 pages
    English and French language
    sale 15% off

2016-01-12: no BT decision available about extension of DOW = DOR + 60 months
2015-04-17: Extension of DOW = DOR + 60 Months to be requested to CLC/BT.

  • Amendment
    6 pages
    English language
    sale 10% off
    e-Library read for
    1 day

IEC 60947-4-1:2018 is available as IEC 60947-4-1:2018 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.
IEC 60947-4-1:2018 is applicable to the following equipment:
- electromechanical contactors and starters including motor protective switching device (MPSD);
- actuators of contactor relays;
- contacts dedicated exclusively to the coil circuit of this contactor or this contactor relay;
- dedicated accessories (e.g. dedicated wiring, dedicated latch accessory);
intended to be connected to distribution circuits, motors circuits and other load circuits, the rated voltage of which does not exceed 1 000 V AC or 1 500 V DC. This fourth edition cancels and replaces the third edition published in 2009 and its Amendment 1:2012. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition:
- Scope structure and exclusions
- Editorial correction of notes and hanging paragraphs
- Reference to IEC 62683-1
- Motor protective switching device (MPSD) with its requirements
- Safety aspects related to:
- General aspects;
- Limited energy circuits;
- Electronic circuits;
- Assessment procedure for electromechanical overload protection used in safety -applications (new Annex L)
- Introduction of provisions covering the impact of higher locked rotor current to achieve high efficiency class
- Mention of dedicated wiring accessories
- Pickup power measurement
- Alignment to IEC 60947-1:2007, IEC 60947-1:2007/AMD1:2010, and IEC 60947‑1:2007/AMD2:2014
- Direct current requirements for covering photovoltaic application (new Annex M)
- Load monitoring indicators (new Annex O)
- Short-circuit breaking tests of MPSD (new Annex P)
- Co-ordination under short-circuit conditions between a MPSD and another short-circuit protective device associated in the same circuit (new Annex Q).
The contents of the interpretation sheet of March 2020, the corrigendum 1 of April 2020 and the corrigendum 2 of April 2021 have been included in this copy.

  • Standard
    371 pages
    English and French language
    sale 15% off

IEC 62275:2018 specifies requirements for metallic, non-metallic and composite cable ties and their associated fixing devices used for the management and support of wiring systems in electrical installations.
This third edition cancels and replaces the second edition published in 2013. This edition constitutes a technical revision.
This edition includes the following significant technical changes with respect to the previous edition:
a) consideration of adhesive fixing devices,
b) revised and updated normative references,
c) modified definitions for metallic and composite cable ties,
d) new definitions,
e) improvement of test procedures,
f) new figures for typical arrangement of test assembly for fixing devices and for integral fixing devices.

  • Standard
    82 pages
    English and French language
    sale 15% off

IEC 60358-4:2018 applies to DC or AC single-phase capacitor-dividers connected between line and ground used for manufacturing Voltage Transformers as well as for other applications. IEC 60358-4:2018 is to be used in conjunction with the latest edition of IEC 60358-1 and its amendments. IEC 60358-4:2018 was established on the basis of the IEC 60358-1:2012. IEC 60358-4:2018 supplements or modifies the corresponding clauses in IEC 60358-1:2012. This standard cancels and replaces the second edition of IEC 60358 (1990), and constitutes a technical revision.

  • Standard
    26 pages
    English and French language
    sale 15% off

IEC 63044-1:2017 applies to all Home and Building Electronic Systems (HBES) and Building Automation and Control Systems (BACS) and specifies the general requirements for these systems and products. This document is applicable (but not limited) to   operator stations and other human–system interface devices,  devices for management functions,  control devices, automation stations and application specific controllers,  field devices and their interfaces, and  cabling and interconnection of devices  used within a dedicated HBES/BACS network. This document provides an overview of the IEC 63044 series. To enable integration of a wide spectrum of applications, the IEC 63044 series covers   electrical safety,  functional safety,  environmental conditions,  EMC requirements, and  installation and cabling rules and topologies.  IEC 63044 is a series of product family standards. Keywords: Smart Homes, Smart Cities, Home automation

  • Standard
    13 pages
    English language
    sale 10% off
    e-Library read for
    1 day

D156/C038 - BT approved the British NC request for modification of an SNC in EN 61242:1997 and invited CCMC to issue the corresponding amendment.

  • Amendment
    3 pages
    English language
    sale 10% off
    e-Library read for
    1 day

IEC 60831-2:2014 applies to capacitors according to IEC 60831-1 and gives the requirements for the ageing test, self-healing test and destruction test for these capacitors. This third edition cancels and replaces the second edition published in 1995. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: - Updating of the normative references; - Discharge cycles before ageing test carried out at ambient temperature; - Alternative Self-healing test at d.c. voltage; - Modified acceptance conditions after Self-healing test; - Modifications to Destruction test. Keywords: IEC 60831-1, requirements for the ageing test, self-healing test and destruction test for capacitors

  • Standard
    14 pages
    English language
    sale 10% off
    e-Library read for
    1 day

NEW! IEC 60831-1:2014 is available as IEC Standards+ 60831-1:2014 which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition. IEC 60831-1:2014 is applicable to both capacitor units and capacitor bank s intended to be used, particularly, for power-factor correction of a.c. power systems having a rated voltage up to and including 1 000 V and frequencies of 15 Hz to 60 Hz. This part of IEC 60831 also applies to capacitors intended for use in power filter circuit s. Additional definitions, requirements, and tests for power filter capacitors are given in Annex A. The object of this part of IEC 60831 is to: - formulate uniform rules regarding performances, testing and rating; - formulate specific safety rules; - provide a guide for installation and operation. This third edition cancels and replaces the second edition published in 1996 and Amendment 1:2002. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: - Updating of the normative references; - Test conditions have been clarified; - Thermal stability test has been clarified; - Maximum permissible voltage and current have been clarified; - The protection of the environment has been amended with safety concerns and plastic quality requirements. Keywords: capacitor units and capacitor banks, uniform rules regarding performances, testing and rating; safety rules; guide for installation and operation

  • Standard
    40 pages
    English language
    sale 10% off
    e-Library read for
    1 day