Plastics - Acquisition and presentation of comparable multipoint data - Part 3: Environmental influences on properties (ISO 11403-3:2014)

ISO 11403-3:2014 specifies test procedures for the acquisition and presentation of multipoint data which demonstrate the behaviour of plastics under the following environments:
prolonged exposure to heat;
liquid chemicals;
environmental stress cracking under a constant tensile stress;
artificial weathering.
The tests are listed in order of increasing severity of the environment. By testing under the least severe environments first, it is possible to make informed judgements regarding whether tests under more severe conditions are worthwhile.

Kunststoffe - Ermittlung und Darstellung von vergleichbaren Vielpunkt-Kennwerten - Teil 3: Umgebungseinflüsse auf Eigenschaften (ISO 11403-3:2014)

Dieser Teil von ISO 11403 legt Prüfverfahren fest für die Ermittlung und Darstellung von Vielpunkt-Kennwerten, die das Verhalten von Kunststoffen gegenüber den folgenden Umgebungseinflüssen darstellen:
-   langanhaltende Wärmeeinwirkung;
-   flüssige Medien;
-   umgebungsbedingte Spannungsrissbildung unter konstanter Zugspannung;
-   künstliche Bewitterung.
Die Prüfungen sind in der Reihenfolge zunehmender Schärfe aufgeführt. Durch Prüfung bei weniger scharfen Umgebungseinflüssen ist es möglich zu entscheiden, ob Prüfungen unter schärferen Bedingungen sinnvoll sind.

Plastiques - Acquisition et présentation de données multiples comparables - Partie 3: Effets induits par l'environnement sur les propriétés (ISO 11403-3:2014)

L'ISO 11403-3:2014 spécifie les modes opératoires d'essai en vue de l'acquisition et de la présentation de données multiples qui démontrent le comportement des plastiques dans les environnements suivants:
exposition prolongée à la chaleur;
produits chimiques liquides;
fissuration dans un environnement donné sous contrainte de traction constante;
vieillissement artificiel.
Les essais sont indiqués par ordre de sévérité croissante de l'effet de l'environnement. Commencer par les environnements les moins sévères permet de juger en toute connaissance de cause s'il vaut la peine d'effectuer des essais dans des conditions plus sévères.

Polimerni materiali - Pridobitev in predstavitev primerljivih podatkov, dobljenih pri različnih pogojih - 3. del: Vplivi okolja na lastnosti (ISO 11403-3:2014)

Standard EN ISO 11403-3 določa preskusne postopke za pridobitev in predstavitev podatkov, dobljenih pri različnih pogojih, ki se v naslednjih okoljih obnašajo kot polimerni materiali: - dolgotrajna izpostavljenost vročini; - kemikalije v tekočem stanju; - napetostna korozija pri stalni natezni obremenitvi; - umetna izpostavljenost vremenskim vplivom. Preskusi so navedeni po vrstnem redu odvisno od zahtevnosti okolja. S preskušanjem najprej v najmanj zahtevnih okoljih je mogoče ustrezno oceniti, ali so potrebni preskusi v resnejših pogojih.

General Information

Status
Withdrawn
Publication Date
17-Jun-2014
Withdrawal Date
29-Jun-2021
Technical Committee
Drafting Committee
Current Stage
9960 - Withdrawal effective - Withdrawal
Completion Date
30-Jun-2021

Relations

Buy Standard

Standard
EN ISO 11403-3:2014
English language
22 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day
Draft
k FprEN ISO 11403-3:2014
English language
20 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 11403-3:2014
01-september-2014
1DGRPHãþD
SIST EN ISO 11403-3:2002
3ROLPHUQLPDWHULDOL3ULGRELWHYLQSUHGVWDYLWHYSULPHUOMLYLKSRGDWNRYGREOMHQLKSUL
UD]OLþQLKSRJRMLKGHO9SOLYLRNROMDQDODVWQRVWL ,62
Plastics - Acquisition and presentation of comparable multipoint data - Part 3:
Environmental influences on properties (ISO 11403-3:2014)
Kunststoffe - Ermittlung und Darstellung von vergleichbaren Vielpunkt-Kennwerten - Teil
3: Umgebungseinflüsse auf Eigenschaften (ISO 11403-3:2014)
Plastiques - Acquisition et présentation de données multiples comparables - Partie 3:
Effets induits par l'environnement sur les propriétés (ISO 11403-3:2014)
Ta slovenski standard je istoveten z: EN ISO 11403-3:2014
ICS:
83.080.01 Polimerni materiali na Plastics in general
splošno
SIST EN ISO 11403-3:2014 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 11403-3:2014

---------------------- Page: 2 ----------------------

SIST EN ISO 11403-3:2014

EUROPEAN STANDARD
EN ISO 11403-3

NORME EUROPÉENNE

EUROPÄISCHE NORM
June 2014
ICS 83.080.01 Supersedes EN ISO 11403-3:2001
English Version
Plastics - Acquisition and presentation of comparable multipoint
data - Part 3: Environmental influences on properties (ISO
11403-3:2014)
Plastiques - Acquisition et présentation de données Kunststoffe - Ermittlung und Darstellung von vergleichbaren
multiples comparables - Partie 3: Effets induits par Vielpunkt-Kennwerten - Teil 3: Umgebungseinflüsse auf
l'environnement sur les propriétés (ISO 11403-3:2014) Eigenschaften (ISO 11403-3:2014)
This European Standard was approved by CEN on 7 June 2014.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same
status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United
Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2014 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 11403-3:2014 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN ISO 11403-3:2014
EN ISO 11403-3:2014 (E)
Contents Page
Foreword .3
2

---------------------- Page: 4 ----------------------

SIST EN ISO 11403-3:2014
EN ISO 11403-3:2014 (E)
Foreword
This document (EN ISO 11403-3:2014) has been prepared by Technical Committee ISO/TC 61 “Plastics” in
collaboration with Technical Committee CEN/TC 249 “Plastics” the secretariat of which is held by NBN.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by December 2014, and conflicting national standards shall be withdrawn
at the latest by December 2014.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 11403-3:2001.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece,
Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.
Endorsement notice
The text of ISO 11403-3:2014 has been approved by CEN as EN ISO 11403-3:2014 without any modification.
...

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Kunststoffe - Ermittlung und Darstellung von vergleichbaren Vielpunkt-Kennwerten - Teil 3: Umgebungseinflüsse auf Eigenschaften (ISO/FDIS 11403-3:2014)Plastiques - Acquisition et présentation de données multiples comparables - Partie 3: Effets induits par l'environnement sur les propriétés (ISO/FDIS 11403-3:2014)Plastics - Acquisition and presentation of comparable multipoint data - Part 3: Environmental influences on properties (ISO/FDIS 11403-3:2014)83.080.01Polimerni materiali na splošnoPlastics in generalICS:Ta slovenski standard je istoveten z:FprEN ISO 11403-3kSIST FprEN ISO 11403-3:2014en,de01-april-2014kSIST FprEN ISO 11403-3:2014SLOVENSKI
STANDARD



kSIST FprEN ISO 11403-3:2014



© ISO 2014Plastics — Acquisition and presentation of comparable multipoint data —Part 3: Environmental in Ðluences on propertiesPlastiques — Acquisition et présentation de données multiples comparables —Partie 3: Effets induits par l’environnement sur les propriétésINTERNATIONAL STANDARDPlease see the administrative notes on page iiiReference numberISO/FDIS 11403-3:2014(E)ISO/FDIS11403-3ISO/TC 61/SC 2Secretariat: AENORVoting begins on: 2014-Voting terminates on: 2014-RECIPIENTS OF THIS DRAFT ARE INVITED TO SUBMIT, WITH THEIR COMMENTS, NOTIFICATION OF ANY RELEVANT PATENT RIGHTS OF WHICH THEY ARE AWARE AND TO PROVIDE SUPPOR TING DOCUMENTATION.IN ADDITION TO THEIR EVALUATION AS
BEING ACCEPTABLE FOR INDUSTRIAL, TECHNO-LOGICAL, COMMERCIAL AND USER PURPOSES, DRAFT INTERNATIONAL STANDARDS MAY ON OCCASION HAVE TO BE CONSIDERED IN THE LIGHT OF THEIR POTENTIAL TO BECOME STAN-DARDS TO WHICH REFERENCE MAY BE MADE IN NATIONAL REGULATIONS.FINALDRAFTkSIST FprEN ISO 11403-3:2014



ISO/FDIS 11403-3:2014(E) ii © ISO 2014 – All rights reservedCOPYRIGHT PROTECTED DOCUMENT©
ISO 2014All rights reservedä Unless otherwise speci Ðiedá no part of this publication may be reproduced or utilized otherwise in any form or by any meansá electronic or mechanicalá including photocopyingá or posting on the internet or an intranetá without prior written permissionä Permission can be requested from either ISO at the address below or ISOïs member body in the country of the requester.ISO copyright of ÐiceTel. + 41 22 749 01 11Fax + 41 22 749 09 47Eæmail copyright 7isoäorgWeb www.iso.orgPublished in SwitzerlandkSIST FprEN ISO 11403-3:2014



ISO/CEN PARALLEL PROCESSING-cessed under the ISO-lead mode of collaboration as de Ðined in the Vienna Agreementä The
Ðinal draft was established on the basis of comments received during a parallel enquiry on the draftäThis
Ðinal draft is hereby submitted to the ISO member bodies and to the CEN member bodies for a parallel two-month approval vote in ISO and formal vote in CEN.Positive votes shall not be accompanied by comments.Negative votes shall be accompanied by the relevant technical reasons.ISO/FDIS 11403-3:2014(E) © ISO 2014 – All rights reserved iiikSIST FprEN ISO 11403-3:2014



ISO/FDIS 11403-3:2014(E) iv © ISO 2014 – All rights reservedContents PageForeword .vIntroduction .vi1 Scope .12 Normative references .1 u Terms and de Ðinitions .24 Specimen preparation .25 Conditioning .36 Test requirements .36.1 General .
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.