EN ISO 25178-73:2019
(Main)Geometrical product specifications (GPS) - Surface texture: Areal - Part 73: Terms and definitions for surface defects on material measures (ISO 25178-73:2019)
Geometrical product specifications (GPS) - Surface texture: Areal - Part 73: Terms and definitions for surface defects on material measures (ISO 25178-73:2019)
This document defines classes of geometrical defects that might be present on the surfaces of material measures and calibration specimens conforming to ISO 5436-1 and ISO 25178-70, and defines terms for ways of responding to these defects.
This document is applicable as follows:
a) to help customers and users of material measures for surface metrology specify their nominal features (ideal geometrical properties) when obtaining them from manufacturers and suppliers;
b) to enable users of material measures to formulate their own rules and policies for responding to the occurrence of defects in such a way as to minimize the uncertainty of their own measurements;
NOTE Such policies are required in ISO/IEC 17025:2017, 7.2.1.1, 7.2.1.3, 7.3.1 and 7.8.5 c) and d), for example.
c) to enable calibration laboratories and their customers to agree on a common policy on how to treat defects on a material measure that has been sent for calibration;
d) to educate users of material measures about the different significance and importance of different kinds of defect;
e) for other GPS standards which make reference to the issue of selection of measuring locations, or selection of areas to be measured or avoided in measurement.
Geometrische Produktspezifikation (GPS) - Oberflächenbeschaffenheit: Flächenhaft - Teil 73: Begriffe für Oberflächenfehler an Maßverkörperungen (ISO 25178-73:2019)
Dieses Dokument definiert Klassen geometrischer Fehler, die an den Oberflächen von Maßverkörperungen und Kalibrierkörpern nach ISO 5436 1 und ISO 25178 70 auftreten können und Begriffe für Arten des Umgangs mit diesen Fehlern.
Dieses Dokument gilt für Folgendes:
a) Kunden und Anwendern von Maßverkörperungen für die Oberflächenmesstechnik dabei zu helfen, ihre Nenngeometrieelemente (ideale geometrische Eigenschaften) festzulegen, wenn sie diese von Herstellern und Lieferanten erhalten;
b) Anwendern von Maßverkörperungen zu ermöglichen, ihre eigenen Regeln und Richtlinien zu formulieren, um mit auftretenden Fehler so umzugehen, dass die Unsicherheit ihrer eigenen Messungen minimiert wird;
ANMERKUNG Solche Richtlinien werden z. B. in ISO/IEC 17025:2017, 7.2.1.1, 7.2.1.3, 7.3.1 und 7.8.5 c) und d) gefordert.
c) Kalibrierlaboren und ihren Kunden zu ermöglichen, eine gemeinsame Richtlinie zum Umgang mit Fehlern an einer zu kalibrierenden Maßverkörperung zu vereinbaren;
d) Anwender von Maßverkörperungen über die unterschiedliche Bedeutung und Wichtigkeit von verschiedenen Fehlerarten aufzuklären;
e) für andere GPS Normen, die auf das Problem der Auswahl von Messorten oder der zu messenden oder bei der Messung zu vermeidenden Bereiche verweisen.
Spécification géométrique des produits (GPS) - État de surface: surfacique - Partie 73: Termes et définitions pour les défauts de surface sur les mesures matérialisées (ISO 25178-73:2019)
Le présent document traite des défauts géométriques pouvant être présents sur les surfaces des mesures matérialisées et des échantillons d'étalonnage conformes à l'ISO 5436-1 et à l'ISO 25178-70 et définit les termes désignant les manières de répondre à ces défauts.
Le présent document est applicable comme suit:
a) pour aider les clients et les utilisateurs de mesures matérialisées en métrologie de surface à spécifier leurs éléments nominaux (propriétés géométriques idéales) en cas d'obtention de ces mesures auprès des fabricants et des fournisseurs;
b) pour permettre aux utilisateurs de mesures matérialisées de formuler leurs propres règles et politiques pour répondre à l'occurrence de défauts de manière à réduire le plus possible l'incertitude de leurs propres mesurages;
NOTE Ces politiques sont par exemple requises dans l'ISO/IEC 17025:2017, 7.2.1.1, 7.2.1.3, 7.3.1 et 7.8.5 c) et d).
c) pour permettre aux laboratoires d'étalonnage et à leurs clients de convenir d'une politique commune sur la manière de traiter les défauts présents sur une mesure matérialisée ayant été envoyée en vue d'être étalonnée;
d) pour former les utilisateurs de mesures matérialisées à la signification et à l'importance variable des différents types de défauts;
e) pour les autres normes GPS qui font référence à la question du choix des emplacements de mesure ou du choix des zones à mesurer ou des zones à éviter lors du mesurage.
Specifikacija geometrijskih veličin izdelka (GPS) - Tekstura površine: ravna - 73. del: Izrazi in definicije za površinske napake pri meritvah materiala (ISO 25178-73:2019)
Ta del standarda ISO 25178 obravnava geometrijske napake, ki so lahko prisotne na površinah materialov in kalibracijskih preskušancev v skladu s standardoma ISO 5436-1 in ISO 25178-70. Opredeljuje razrede teh geometrijskih napak in določa načine odzivanja na te pomanjkljivosti.
Ta del standarda ISO 25178 se uporablja za:
a) pomoč kupcem in uporabnikom meritev materialov pri meroslovju površin, da pri nakupu od proizvajalcev in dobaviteljev določijo njihove nazivne lastnosti (idealne geometrijske lastnosti);
b) podporo uporabnikom meritev materialov, da oblikujejo svoja pravila in pravilnike za odzivanje na pojavljanje napak s tem, da zmanjšajo negotovost svojih lastnih meritev;
c) podporo laboratorijem za umerjanje in njihovim strankam, da se dogovorijo o skupni politiki ravnanja z napakami pri meritvah materialov, poslanih na umerjanje;
d) izobraževanje uporabnikov meritev materialov o različnem pomenu in pomenu različnih vrst napak;
e) druge standarde GPS, ki se sklicujejo na vprašanje izbire merilnih mest ali izbire območij, ki jih je treba izmeriti oziroma se jih pri merjenju izogibati.
General Information
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 25178-73:2019
01-september-2019
Specifikacija geometrijskih veličin izdelka (GPS) - Tekstura površine: ravna - 73.
del: Izrazi in definicije za površinske napake pri meritvah materiala (ISO 25178-
73:2019)
Geometrical product specifications (GPS) - Surface texture: Areal - Part 73: Terms and
definitions for surface defects on material measures (ISO 25178-73:2019)
Geometrische Produktspezifikation (GPS) - Oberflächenbeschaffenheit: Flächenhaft -
Teil 73: Begriffe für Oberflächenfehler an Maßverkörperungen (ISO 25178-73:2019)
Spécification géométrique des produits (GPS) - État de surface: surfacique - Partie 73:
Termes et définitions pour les défauts de surface sur les mesures matérialisées (ISO
25178-73:2019)
Ta slovenski standard je istoveten z: EN ISO 25178-73:2019
ICS:
01.040.17 Meroslovje in merjenje. Metrology and measurement.
Fizikalni pojavi (Slovarji) Physical phenomena
(Vocabularies)
17.040.40 Specifikacija geometrijskih Geometrical Product
veličin izdelka (GPS) Specification (GPS)
SIST EN ISO 25178-73:2019 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 25178-73:2019
---------------------- Page: 2 ----------------------
SIST EN ISO 25178-73:2019
EN ISO 25178-73
EUROPEAN STANDARD
NORME EUROPÉENNE
June 2019
EUROPÄISCHE NORM
ICS 01.040.17; 17.040.40
English Version
Geometrical product specifications (GPS) - Surface texture:
Areal - Part 73: Terms and definitions for surface defects
on material measures (ISO 25178-73:2019)
Spécification géométrique des produits (GPS) - État de Geometrische Produktspezifikation (GPS) -
surface: surfacique - Partie 73: Termes et définitions Oberflächenbeschaffenheit: Flächenhaft - Teil 73:
pour les défauts de surface sur les mesures Begriffe für Oberflächenfehler an Maßverkörperungen
matérialisées (ISO 25178-73:2019) (ISO 25178-73:2019)
This European Standard was approved by CEN on 3 May 2019.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, North
Macedonia, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United
Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2019 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 25178-73:2019 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 25178-73:2019
EN ISO 25178-73:2019 (E)
Contents Page
European foreword . 3
2
---------------------- Page: 4 ----------------------
SIST EN ISO 25178-73:2019
EN ISO 25178-73:2019 (E)
European foreword
This document (EN ISO 25178-73:2019) has been prepared by Technical Committee ISO/TC 213
"Dimensional and geometrical product specifications and verification" in collaboration with Technical
Committee CEN/TC 290 “Dimensional and geometrical product specification and verification” the
secretariat of which is held by AFNOR.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by December 2019, and conflicting national standards
shall be withdrawn at the latest by December 2019.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
Fran
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.