Plastics piping systems for water supply and for buried and above ground drainage, sewerage and irrigation under pressure - Oriented unplasticized poly(vinyl chloride) (PVC-O) - Part 1: General

This part of FprEN 17176 specifies the material characteristics of oriented unplasticized poly(vinyl chloride) (PVC-O) solid wall piping systems intended for water supply and for buried drainage, sewerage and irrigation under pressure  or above-ground where protected from direct sunlight.
In conjunction with FprEN 17176-2, FprCEN/TS 17176-3 and EN ISO 1452-3, it is applicable to PVC-O pipes, PVC-O fittings, their joints and to joints with components of other plastics and non-plastics materials intended to be used for the following:
a)   water mains and services lines;
b)   conveyance of water for both outside and inside buildings;
c)   drainage, sewerage and treated waste water under pressure;
d)    irrigation under pressure.
Joints constructed of other materials shall meet their own standards in addition to the fitness of purpose requirements specified in FprEN 17176-5.
It is applicable to piping systems intended for the supply of water with a maximum allowable operating pressure (PFA) up to and including 25 bar . The piping system according to this document is intended for the conveyance of cold water up to and including 45 °C and especially in those applications where special performance requirements are needed, such as impact loads and pressure fluctuations.
For temperatures between 25 °C and 45 °C, FprEN 17176-2:2018, Figure C.1 applies.
NOTE   It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their particular requirements and any relevant national regulations and installation practices or codes.

Kunststoff-Rohrleitungssysteme für die Wasserversorgung und für erdverlegte und nicht erdverlegte Entwässerungs-, Abwasser- und Bewässerungsdruckleitungen - Orientiertes weichmacherfreies Polyvinylchlorid (PVC-O) - Teil 1: Allgemeines

Dieser Teil von EN 17176 legt die Werkstoffeigenschaften von vollwandigen Rohrleitungssystemen aus orientiertem weichmacherfreiem Polyvinylchlorid (PVC O) fest, die für die Wasserversorgung und für erdverlegte und nicht erdverlegte, vor direkter Sonneneinstrahlung geschützte Entwässerungs , Abwasser  und Bewässerungsdruckleitungen vorgesehen sind.
Zusammen mit EN 17176 2, CEN/TS 17176 3 und EN ISO 1452 3 gilt er für PVC O Rohre, PVC O Formstücke, deren Verbindungen untereinander sowie für Verbindungen mit Bauteilen aus anderen Kunststoffen und aus anderen, nicht aus Kunststoff bestehenden Werkstoffen, die für folgende Anwendungsgebiete vorgesehen sind:
a)   Versorgungs- und Hausanschlussleitungen;
b)   Durchleitung von Wasser sowohl außerhalb als auch innerhalb von Gebäuden;
c)   Entwässerung, Abwasser und behandeltes Abwasser unter Druck;
d)   Bewässerung unter Druck.
Verbindungen aus anderen Werkstoffen müssen deren Normen zusätzlich zu den in EN 17176 5 festgelegten Anforderungen an die Gebrauchstauglichkeit entsprechen.
Dieser Teil ist anwendbar auf Rohrleitungssysteme, die für die Versorgung mit Wasser mit einem maximal zulässigen Bauteilbetriebsdruck (PFA) bis einschließlich 25 bar ) vorgesehen sind. Das Rohrleitungssystem nach diesem Dokument ist für die Durchleitung von Kaltwasser bis einschließlich 45 °C vorgesehen und besonders bei solchen Anwendungen, bei denen besondere Leistungsanforderungen gelten, wie z. B. Stoßbelastungen und Druckschwankungen.
Für Temperaturen zwischen 25 °C und 45 °C gilt EN 17176 2:2018, Bild C.1.
ANMERKUNG   Der Käufer oder Auftraggeber ist unter Berücksichtigung der eigenen Anforderungen sowie der geltenden nationalen Bestimmungen und Verlegeverfahren oder -vorschriften für die entsprechende Auswahl dieser Eigenschaften verantwortlich.

Systèmes de canalisations en plastique pour l’alimentation en eau, les branchements et collecteurs d’assainissement et les systèmes d’irrigation sous pression, enterrés ou aériens - Poly(chlorure de vinyle) non plastifié orienté (PVC-O) - Partie 1 : Généralités

La présente partie de l’EN 17176 spécifie les caractéristiques de la matière des systèmes de canalisations à paroi compacte en poly(chlorure de vinyle) non plastifié orienté (PVC-O) destinés à l’alimentation en eau, aux branchements, aux collecteurs d’assainissement et aux systèmes d’irrigation sous pression, enterrés ou aériens lorsqu’ils sont protégés des rayons directs du soleil.
Conjointement avec l’EN 17176 2, la CEN/TS 17176 3 et l’EN ISO 1452 3, elle s’applique aux tubes en PVC O, aux raccords en PVC O ainsi qu’à leurs assemblages, et aux assemblages avec des composants à base d’autres matières, plastiques ou non plastiques, pouvant être utilisés pour les usages suivants :
a)   les conduites principales et les conduites de branchement ;
b)   le transport de l’eau à l’extérieur et à l’intérieur des bâtiments ;
c)   les branchements et collecteurs d’assainissement et les systèmes d’eaux usées traitées sous pression ;
d)    l’irrigation sous pression.
Les assemblages fabriqués avec d'autres matières seront conformes à leurs propres normes, en plus des exigences d'aptitude à l'emploi spécifiées dans l’EN 17176-5.
Elle s’applique aux systèmes de canalisations destinés à l’alimentation en eau avec une pression de service admissible (PFA) maximale jusqu’à 25 bar  inclus. Le système de canalisations conforme au présent document est destiné au transport d’eau froide jusqu’à 45 °C inclus et, notamment pour les applications dans lesquelles des exigences de performance spéciales sont nécessaires, par exemple en cas de charges dynamiques et de fluctuations de pression.
Pour des températures comprises entre 25 °C et 45 °C, l’EN 17176-2:2018, Figure C.1 s’applique.
NOTE   Il est de la responsabilité de l'acheteur ou du concepteur du réseau d'effectuer les choix appropriées à partir de ces données en tenant compte des exigences particulières et des éventuelles règles nationales concernées et des pratiques ou codes de pose.

Cevni sistemi iz polimernih materialov za oskrbo z vodo in za podzemne in nadzemne sisteme odvodnjavanja, kanalizacije ter namakanja pod tlakom - Orientiran nemehčan polivinilklorid (PVC-O) - 1. del: Splošno

Ta del standarda prEN 17176 določa splošne vidike orientiranega nemehčanega polivinilklorida (PVC-O) za podzemne in nadzemne trde cevne sisteme za oskrbo z vodo, kanalizacijo in namakanje pod tlakom, kjer so ti sistemi zaščiteni pred neposredno sončno svetlobo.
V povezavi s standardi prEN 17176-2, prEN 17176-3 in EN ISO 1452 4 se uporablja za cevi in fitinge iz orientiranega nemehčanega polivinilklorida ter ventile, njihove spoje ter spoje s sestavnimi deli iz drugih polimernih in nepolimernih materialov, ki se uporabljajo za:
a) vodovod in priključke na vodovod;
b) prenos vode zunaj in znotraj stavb;
c) odvodnjavanje, kanalizacijo in čiščenje odpadne vode pod tlakom;
d) namakanje pod tlakom.
Uporablja se za cevni sistem, namenjen dovajanju vode pod tlakom do vključno 25 °C (hladna voda), ki je namenjena za pitje in za splošne namene ter tudi za odpadne vode pod tlakom.
Ta del standarda prEN 17176 se uporablja tudi za komponente za prenos vode in odpadne vode s temperaturo do vključno 45 °C. Za temperature med 25 °C in 45 °C se uporablja slika C.1 iz standarda prEN 17176-2:2017.
Cevni sistem je v skladu s tem evropskim standardom namenjen za prenos hladne vode z največjim tlakom do 25 barov in predvsem v namene, ko so potrebne posebne zahteve, kot so udarne obremenitve in nihanje tlaka, z največjim tlakom do 25 barov.

General Information

Status
Published
Publication Date
16-Apr-2019
Withdrawal Date
30-Oct-2019
Current Stage
6060 - Definitive text made available (DAV) - Publishing
Start Date
17-Apr-2019
Due Date
15-Apr-2019
Completion Date
17-Apr-2019

Buy Standard

Standard
EN 17176-1:2019
English language
14 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day
Draft
prEN 17176-1:2018
English language
14 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 17176-1:2019
01-julij-2019
Cevni sistemi iz polimernih materialov za oskrbo z vodo in za podzemne in
nadzemne sisteme odvodnjavanja, kanalizacije ter namakanja pod tlakom -
Orientiran nemehčan polivinilklorid (PVC-O) - 1. del: Splošno
Plastics piping systems for water supply and for buried and above ground drainage,
sewerage and irrigation under pressure - Oriented unplasticized poly(vinyl chloride)
(PVC-O) - Part 1: General
Kunststoff-Rohrleitungssysteme für die Wasserversorgung und für erdverlegte und nicht
erdverlegte Entwässerungs-, Abwasser- und Bewässerungsdruckleitungen - Orientiertes
weichmacherfreies Polyvinylchlorid (PVC-O) - Teil 1: Allgemeines
Systèmes de canalisations en plastique pour l’alimentation en eau, les branchements et
collecteurs d’assainissement et les systèmes d’irrigation sous pression, enterrés ou
aériens - Poly(chlorure de vinyle) non plastifié orienté (PVC-O) - Partie 1 : Généralités
Ta slovenski standard je istoveten z: EN 17176-1:2019
ICS:
23.040.20 Cevi iz polimernih materialov Plastics pipes
91.140.80 Drenažni sistemi Drainage systems
93.030 Zunanji sistemi za odpadno External sewage systems
vodo
SIST EN 17176-1:2019 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 17176-1:2019

---------------------- Page: 2 ----------------------

SIST EN 17176-1:2019


EN 17176-1
EUROPEAN STANDARD

NORME EUROPÉENNE

April 2019
EUROPÄISCHE NORM
ICS 23.040.20; 23.040.45
English Version

Plastics piping systems for water supply and for buried
and above ground drainage, sewerage and irrigation under
pressure - Oriented unplasticized poly(vinyl chloride)
(PVC-O) - Part 1: General
Systèmes de canalisations en plastique pour Kunststoff-Rohrleitungssysteme für die
l'alimentation en eau, les branchements et collecteurs Wasserversorgung und für erdverlegte und nicht
d'assainissement et les systèmes d'irrigation sous erdverlegte Entwässerungs-, Abwasser- und
pression, enterrés ou aériens - Poly(chlorure de vinyle) Bewässerungsdruckleitungen - Orientiertes
non plastifié orienté (PVC-O) - Partie 1 : Généralités weichmacherfreies Polyvinylchlorid (PVC-O) - Teil 1:
Allgemeines
This European Standard was approved by CEN on 14 January 2019.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2019 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 17176-1:2019 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN 17176-1:2019
EN 17176-1:2019 (E)
Contents Page
European foreword . 3
Introduction . 4
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 6
4 Symbols and abbreviations . 11
5 Material .
...

SLOVENSKI STANDARD
oSIST prEN 17176-1:2018
01-januar-2018
&HYQLVLVWHPLL]SROLPHUQLKPDWHULDORY]DRVNUER]YRGRLQ]DSRG]HPQHLQ
QDG]HPQHVLVWHPHRGYRGQMDYDQMDNDQDOL]DFLMHWHUQDPDNDQMDSRGWODNRP
2ULHQWLUDQQHPHKþDQSROLYLQLONORULG 39&2 GHO6SORãQR
Plastics piping systems for water supply and for buried and above ground drainage,
sewerage and irrigation under pressure - Oriented unplasticized poly(vinyl chloride) (PVC
-O) - Part 1: General
Kunststoff-Rohrleitungssysteme für die Wasserversorgung und für erdverlegte und nicht
erdverlegte Entwässerungs-, Abwasser- und Bewässerungsdruckleitungen - Orientiertes
weichmacherfreies Polyvinylchlorid (PVC-O) - Teil 1: Allgemeines
Systèmes de canalisations en plastique pour l’alimentation en eau, les branchements et
collecteurs d’assainissement et les systèmes d’irrigation sous pression, enterrés ou
aériens - Poly(chlorure de vinyle) non plastifié orienté (PVC-O) - Partie 1 : Généralités
Ta slovenski standard je istoveten z: prEN 17176-1
ICS:
23.040.20 Cevi iz polimernih materialov Plastics pipes
91.140.80 Drenažni sistemi Drainage systems
93.030 Zunanji sistemi za odpadno External sewage systems
vodo
oSIST prEN 17176-1:2018 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
oSIST prEN 17176-1:2018

---------------------- Page: 2 ----------------------
oSIST prEN 17176-1:2018


DRAFT
EUROPEAN STANDARD
prEN 17176-1
NORME EUROPÉENNE

EUROPÄISCHE NORM

October 2017
ICS 23.040.20; 23.040.45
English Version

Plastics piping systems for water supply and for buried
and above ground drainage, sewerage and irrigation under
pressure - Oriented unplasticized poly(vinyl chloride)
(PVC-O) - Part 1: General
 Kunststoff-Rohrleitungssysteme für die
Wasserversorgung und für erdverlegte und nicht
erdverlegte Entwässerungs-, Abwasser- und
Bewässerungsdruckleitungen - Orientiertes
weichmacherfreies Polyvinylchlorid (PVC-O) - Teil 1:
Allgemeines
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee
CEN/TC 155.

If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations
which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.

This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.

Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.

Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.


EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2017 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 17176-1:2017 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------
oSIST prEN 17176-1:2018
prEN 17176-1:2017 (E)
Contents Page
European foreword . 3
Introduction . 4
1 Scope . 5
2 Normative references . 5
3 Terms, definitions, symbols and abbreviated terms . 6
3.1 Terms and definitions . 6
3.2 Symbols .
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.