CLC - European Committee for Electrotechnical Standardization

IEC 63305:2024 specifies methods and procedures for calibration of vector receivers in the frequency range 5 Hz to 10 kHz, which are applicable to vector receivers based on the two different principles. In addition, it describes an absolute method of inertial vector receiver calibration in air using optical interferometry. Usually, acoustic wave vector receivers are designed and constructed based on one of two principles. One is the sound pressure difference (gradient) principle. When measuring with this sensor, the vector receiver is rigidly fixed on a mount and supported in water. The other is the co-vibrating (inertial) principle. When measuring with this sensor, the vector receiver is suspended on a mount and supported in water in a non-rigid manner, which allows the vector receiver co-vibrate in the same direction as the sound particle in the sound wave field. Many methods have been used to calibrate vector receivers, such as free-field calibration, calibration in standing wave tube and calibration in a travelling wave tube.

IEC 61300-2-44:2024 specifies a test to determine the influence of flexing under tensile load of the strain relief of fibre optic interconnecting devices or components. The intention is to simulate the number of flexing cycles which would typically be experienced during service life. This test is applied to both single fibre cable and multiple fibre cable. This fourth edition cancels and replaces the third edition published in 2013. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: a) replaced active monitoring with transient loss for measurements during test; b) harmonized recommended severities according to IEC 61753-1.

IEC 61169-70:2024, which is a sectional specification (SS), provides information and rules for the preparation of detail specifications (DS) of HD-BNC series RF coaxial connectors together with the pro forma blank detail specification. HD-BNC series connectors with characteristic impedance of 75 Ω are used with RF cables or micro-strips in microwave, telecommunication, wireless and other fields. The operating frequency limit is up to 18 GHz. It also prescribes mating face dimensions for general purpose connectors, gauging information and tests selected from IEC 61169-1, applicable to all detail specifications relating to series HD-BNC RF connectors. This specification indicates the recommended performance characteristics to be considered when writing a detail specification and it covers test schedules and inspection requirements for assessment levels M and H.

IEC 60676:2024 This document specifies the basic test procedures, conditions and methods for establishing the main performance parameters and the main operational characteristics of furnaces for direct arc heating, forming arcs between the electrode and metal, such as electric arc furnaces using alternating current (EAF AC) or direct current (EAF DC), and ladle furnaces (LF), with rated power level above 500 kVA . This fourth edition cancels and replaces the third edition published in 2011. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: a) The structure has been redrafted according to IEC 60398:2015. b) The scope has been redrafted. c) The terms/definitions, normative references and bibliography have been updated and completed. d) The test methods and content from IEC 60398:2015 have been confirmed, replaced, or complemented with regards to direct arc furnaces (EAF, LF). e) The annexes from IEC 60398:2015 have been confirmed, replaced, or complemented with regards to direct arc furnaces (EAF, LF).

IEC 62836:2024 provides an efficient and reliable procedure to test the internal electric field in the insulating materials used for high-voltage applications, by using the pressure wave propagation (PWP) method. It is suitable for a planar and coaxial geometry sample with homogeneous insulating materials of thickness larger or equal to 0,5 mm and an electric field higher than 1 kV/mm, but it is also dependent on the thickness of the sample and the pressure wave generator. This first edition cancels and replaces IEC TS 62836 published in 2020. This edition includes the following significant technical changes with respect to IEC TS 62836: a) addition of Clause 12 for the measurement of space charge distribution in a planar sample; b) addition of Clause 13 for coaxial geometry samples; c) addition of Annex D with measurement examples for coaxial geometry samples; d) addition of a Bibliography; e) measurement examples for a planar sample have been moved from Clause 12 in IEC TS 62836 to Annex C.

IEC 60352-9:2024 provides guidelines for welding and testing of ultrasonically welded connections and includes requirements, tests and practical guidance information. Ultrasonic welding is a form of cold friction welding that is becoming increasingly popular in many industries. This type of welding uses ultrasonic vibration to join materials together, creating a bond that is both strong and reliable. Ultrasonic welding has been identified as a process in ISO 4063-41 by the International Organization for Standardization (ISO). The process of ultrasonic welding relies on high frequency ultrasound waves being used to create frictional heat at the connection point. High temperature is not required for this special method of welding, making it one of the most cost-effective ways to join two materials together. It also requires fewer steps than traditional methods, meaning it can be completed quickly and with minimal resources. Ultrasonic welding has been around for decades but only recently has become more widely utilized due to advances in technology and its availability at lower cost. It can be used on many different materials including plastics, rubbers, metals, textiles, and composites. Due to its precision and strong bonds it creates, it has become extremely popular in manufacturing processes such as automotive industry, electronics industry, furniture production and even medical device production. This document covers ultrasonically welded connections made with stranded or flexible wires (class 2, 5 or 6 per IEC 60228) of copper or copper alloy, as well as of aluminium or aluminium alloy. These welded metal-to-metal connections shall employ wires with cross-sectional area of 0,08 mm2 to 160 mm2 and shall not exceed a total cross-sectional area, in case of wire bundle, of 200 mm2. For aluminium or aluminium alloy wires, the minimum required cross-sectional area is 2,5 mm2. Additionally, information on materials, data from industrial experience and test procedures are included to ensure electrically stable connections under prescribed environmental conditions. Lastly, this document aims to achieve comparable results when using ultrasonic welding equipment with similar performance and specifications as specified by the termination manufacturer.

IEC 62282-6-101:2024 covers micro fuel cell power systems and fuel cartridges that are wearable or easily carried by hand, providing direct current outputs that do not exceed 60 V DC and power outputs that do not exceed 240 VA. Portable fuel cell power systems that provide output levels that exceed these electrical limits are covered by IEC 62282-5-100. This document covers micro fuel cell power systems and fuel cartridges. This document establishes the requirements for micro fuel cell power systems and fuel cartridges to ensure a reasonable degree of safety for normal use, reasonably foreseeable misuse, and cargo and consumer transportation and storage of such items. . Fuel cartridges refilled by the manufacturer or by trained technicians are covered by this document. The fuel cartridges covered by this document are not intended to be refilled by the consumer. This first edition, together with the other parts of the IEC 62282-6-1XX series, cancels and replaces IEC 62282-6-100:2010 and IEC 62282-6-100:2010/AMD1:2012. This edition includes the following significant technical changes with respect to IEC 62282‑6‑100:2010 and IEC 62282-6-100:2010/AMD1:2012: a) A new structure has been set up: IEC 62282-6-101 covers the general safety requirements common to all fuel types whereas IEC 62282-6-102 and subsequent parts of the IEC 62282‑6-1XX series cover particular requirements for specific fuel types based on the requirements given in IEC 62282-6-101.

IEC 61169-10:2024, which is a sectional specification (SS), provides information and rules for the preparation of detail specifications (DS) for series SMB RF coaxial connectors with snap-on coupling with a characteristic impedance of 50 Ω. This document prescribes mating face dimensions for high performance connectors – grade 2, dimensional details of standard test connectors − grade 0, gauging information and tests selected from IEC 61169-1, applicable to all detail specifications relating to series SMB RF connectors. This document indicates recommended performance characteristics to be considered when writing a detail specification and it covers test schedules and inspection requirements for assessment levels M and H. The series SMB connectors are used to connect with all kinds of RF cables and microstrips in microwave transmission systems. The operating frequency is up to 4 GHz.

IEC 63118-1:2024 specifies the general tests and requirements for the performance of lithium secondary batteries with a nominal voltage of 12 V permanently installed in road vehicles not for propulsion. The replacement of secondary batteries permanently installed in road vehicles not for propulsion is covered by this document. The following are typical applications that utilize the batteries under the scope of this document: power source for the starting of internal combustion engines, lighting, stop and start function, on-board auxiliary equipment and energy absorption for regeneration from braking. This document includes: - electrical characteristics tests methods and requirements; - a life duration tests method.

IEC 62282-6-106:2024 covers micro fuel cell power systems, micro fuel cell power units and fuel cartridges using hydrogen produced from UN Class 8 (corrosive) borohydride formulations as fuel. These systems and units use proton exchange membrane (PEM) fuel cell technologies. The designs include fuel processing subsystems to derive hydrogen gas from the corrosive fuel formulation. This first edition, together with the other parts of the IEC 62282-6-1XX series, cancels and replaces IEC 62282-6-100:2010 and IEC 62282-6-100:2010/AMD1:2012.This edition includes the following significant technical changes with respect to IEC 62282‑6‑100:2010 and IEC 62282-6-100:2010/AMD1:2012: a) A new structure has been set up: IEC 62282-6-101 covers the general safety requirements common to all fuel types whereas IEC 62282-6-102 and subsequent parts of the IEC 62282-6-1XX series cover particular requirements for individual fuel types.

IEC 60939-3:2024 is available as IEC 60939-3:2024 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.IEC 60939-3:2024 covers passive filters used to attenuate unwanted radio-frequency signals (such as noise or interference) generated from electromagnetic sources. Both single and multi-channel filters within one enclosure or which are built on a printed circuit board forming a compact entity are included within the scope of this document. This document applies to passive filter units for electromagnetic interference suppression for which safety tests are appropriate. This implies that filters specified according to this document will either be connected to mains supplies, when compliance with the mandatory tests of Table B.1 is necessary, or used in other circuit positions where the equipment specification specifies that some or all of these safety tests are required. This document applies to passive filter units, which will be connected to an AC mains or other supply (DC or AC) with a nominal voltage not exceeding 1 000 V AC, with a nominal frequency not exceeding 400 Hz, or 1 500 V DC. Note: For AC use, IEC 60384-14 applies to capacitors which will be connected to AC mains with a nominal frequency not exceeding 100 Hz. This document covers appliance filters (US) but does not cover facility filters, cord-connected filters or direct plug-in filters. These other filters will be covered by another sectional specification. This edition includes the following significant technical changes with respect to the previous edition: a) separated clauses for safety and performance tests; b) added note for use of multiple X capacitors bridging basic insulation in 3 phase filters; c) characteristics and conditions to substitute X and Y capacitors are now described in a separate Subclause 4.1; d) creepage and clearance tables updated and in line with the latest editions of IEC 60938-2 and IEC 60664-1; e) allowing voltage measurement for inductance measurements (7.3); f) added requirements for marking depending on remaining energy after disconnection; g) added content of CTL DSH 2044:2016 for temperature test of IEC filters; h) added note about temperature rise required specimens for safety testing; i) changed index of capacitors in Annex A to avoid confusion between index name and capacitor class; j) moved tests from group 1A to 2. Now, samples in group 1A need to be submitted without potting; k) revision of all parts of the document has taken place based on the ISO/IEC Directives, Part 2:2021, and harmonization with other similar kinds of documents. Annex X contains all cross-references of changes in clause/subclause numbers.

IEC 60034-30-3:2024 specifies efficiency classes for fixed-speed three-phase high-voltage cage induction motors in accordance with IEC 60034-1 that - have a rated voltage exceeding 1 000 V, but not exceeding 11 kV; - have a rated power from 200 kW to 2 000 kW; This document provides the global harmonization of energy-efficiency classes of three-phase cage induction motors with rated voltage above 1 000 V that are rated for direct online starting and fixed-speed operation at a 50 Hz or 60 Hz supply with sinusoidal voltage.

IEC 63403-1:2024 specifies the requirements for specification sheets relating to LED packages designed for horticultural lighting purposes. LED packages designed for horticultural lighting purposes in this document can be designed for emission of white light or emission of optical radiation at specified wavelengths. LED packages for horticultural lighting purposes are usually designed into LED modules or luminaires. This document does not contain compliance criteria, which can be affected by module or luminaire design, and are assumed to be plant species and growth stage dependent.

IEC 60068-2-86:2024 provides a test procedure for use with multi-exciter and multi-axis vibration test systems. The vibration test is intended for general application to components, equipment, and other products, hereinafter referred to as "specimens", subjected to dynamic environments that could arise during an equipment life cycle. Although this document is mainly intended for vibration testing, the procedure is also applied to certain types of shock and transient tests.

IEC 63281-2-1:2024 specifies safety requirements and test methods for personal e-Transporters. This document is applicable to electrically powered personal e-Transporters (PeTs) which are used in private and public areas, where the speed control and/or the steering control is electric/electronic. The PeT can have provisions for transport of cargo and can be for private or commercial (including sharing service) use. This document is not applicable for electric vehicles (EVs), such as electrically power assisted cycles (EPACs), e-bikes, mopeds, motorcycles and passenger cars. This document does not apply to: - PeTs that are considered as toys; - PeTs that are intended for competition; - PeTs that are intended for medical care; - PeTs that have a rated voltage of more than 100 V DC or 240 V AC; - PeTs without an on-board driving operator.

IEC 63403-2:2024 specifies the binning method for LED packages for horticultural lighting.

IEC 60794-2-23: 2024 is a detail specification and specifies indoor multi-fibre cables for use in MPO (multi-fibre push on) connector terminated cable assemblies.

IEC 63203-402-2:2024 specifies test methods for measuring and evaluating the performance, reliability, and accuracy of the step counting feature in any wearable device that can count steps (e.g. activity and fitness trackers, smart bands, smart shoes, and smart insoles). These standard test methods exclude the evaluation of data associated with travel distance or calorie consumption.

IEC 60794-1-312: 2024 describes test procedures to be used in establishing uniform requirements of optical fibre cable elements for the mechanical property – tensile strength and elongation at low temperature. This document applies to optical fibre cables for use with telecommunication equipment and devices employing similar techniques, and to cables having a combination of both optical fibres and electrical conductors. Throughout the document, the wording "optical cable" can also include optical fibre units, microduct fibre units, etc. This document partially cancels and replaces method G11B of IEC 60794-1-23:2019. This edition includes the following significant technical changes with respect to IEC 60794‑1‑23:2019: a) alignment of the title with the content of the method.

IEC 60794-1-311:2024 describes test procedures to be used in establishing uniform requirements of optical fibre cable elements for the mechanical property – tensile strength and elongation at break. This document applies to optical fibre cables for use with telecommunication equipment and devices employing similar techniques, and to cables having a combination of both optical fibres and electrical conductors. Throughout the document, the wording "optical cable" can also include optical fibre units, microduct fibre units, etc. This document partially cancels and replaces IEC 60794-1-23:2019. This edition includes the following significant technical changes with respect to IEC 60794‑1‑23:2019: a) The information about dumb-bells is removed because this is not used for testing cable elements; b) the parameters strain at yield and E modulus are added in 5.7.

IEC 61970-302:2024 specifies a Dynamics package which contains part of the CIM to support the exchange of models between software applications that perform analysis of the steady-state stability (small-signal stability) or transient stability of a power system as defined by IEEE / CIGRE, Definition and classification of power system stability IEEE/CIGRE joint task force on stability terms and definitions. The model descriptions in this document provide specifications for each type of dynamic model as well as the information that needs to be included in dynamic case exchanges between planning/study applications. The scope of the CIM Dynamics package specified in this document includes: • standard models: a simplified approach to describing dynamic models, where models representing dynamic behaviour of elements of the power system are contained in predefined libraries of classes which are interconnected in a standard manner. Only the names of the selected elements of the models along with their attributes are needed to describe dynamic behaviour. • proprietary user-defined models: an approach providing users the ability to define the parameters of a dynamic behaviour model representing a vendor or user proprietary device where an explicit description of the model is not provided by this document. The same libraries and standard interconnections are used for both proprietary user-defined models and standard models. The behavioural details of the model are not documented in this document, only the model parameters. • A model to enable exchange of models’ descriptions. This approach can be used to describe user defined and standard models. • A model to enable exchange of simulation results. This second edition cancels and replaces the first edition published in 2018. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: a) The majority of issues detected in IEC 61970-302:2018 are addressed; b) IEEE 421.5-2016 on Excitation systems is fully covered; c) The IEEE turbine report from 2013 was considered and as a result a number of gas, steam and hydro turbines/governors are added; d) IEC 61400-27-1:2020 on wind turbines is fully incorporated; e) WECC Inverter-Based Resource (IBR) models, Hybrid STATCOM models and storage models are added; f) The user defined models are enhanced with a model which enables modelling of detailed dynamic model; g) A model to enable exchange of simulation results is added; h) The work on the HVDC models is not complete. The HVDC dynamics models are a complex domain in which there are no models that are approved or widely recognised on international level, i.e. there are only project-based models. At this stage IEC 61970-302:2022 only specifies some general classes. However, it is recognised that better coverage of HVDC will require a further edition of this document; i) Models from IEEE 1547-2018 "IEEE Standard for Interconnection and Interoperability of Distributed Energy Resources with Associated Electric Power Systems Interfaces" are added. j) Statements have been added to certain figures, tables, schemas, and enumerations throughout the document that indicate that they are reproduced with the permission of the UCA International User Group (UCAIug). These items are derived from the CIM.

This document is applicable to vertical connecting terminal flags for insulated bushings with rated currents from 250 A to 4 000 A and frequencies from 15 Hz to 60 Hz for liquid immersed equipment.

IEC 60794-2-24:2024 is a detail specification and specifies indoor multiple multi-fibre unit cables for use in MPO (multi-fibre push on) connector terminated breakout cable assemblies.

IEC 63086-2-1:2024 specifies test methods for measuring the performance of electrically powered household and similar air cleaners intended for the reduction of particulate pollutants.

IEC 61757-6-1:2024 defines the terminology, structure, and measurement methods of optical displacement sensors based on fibre Bragg gratings (FBGs) as the sensing element. This document also specifies the most important features and characteristics of these fibre optic displacement sensors and defines procedures for measuring these features and characteristics.

IEC 63203-402-3:2024 specifies terms, a measurement protocol, and a test to evaluate the accuracy of wearables that measure heart rate with a photoplethysmography (PPG) sensor. While this document can be used to measure a variety of different devices claiming to report heart rate, care will be taken when testing in countries that differentiate between heart rate and pulse rate. This measurement protocol is not intended to evaluate medical devices associated with the IEC 60601 series or ISO 80601 series.

This European Standard deals with the safety of commercial electric packaging appliances using vacuum conditions for food preservation, their rated voltage being not more than 250 V for single-phase appliances and 480 V for other appliances

This CENELEC Guide establishes useful guidelines for the preparation and use of standards in the field of electromagnetic compatibility (EMC) in general, and in particular for the implementation of the EMC Directive and the Radio Equipment Directive (RED). This Guide is intended to be used by Technical Committees. The purpose of this guide is to give advice on: - the preparation of dedicated Product and Product Family Standards; - the application of EMC Standards. Certification aspects are not covered by this Guide. NOTE Certification is the action by a third party demonstrating that adequate confidence is provided that a duly identified product, process or service is in conformity with a standard or with other normative documents.

This European Standard deals with the safety of commercial electric packaging appliances using vacuum conditions for food preservation, their rated voltage being not more than 250 V for single-phase appliances and 480 V for other appliances

This document applies to contamination monitors that include warning assembles and meters used for the monitoring of radioactive contamination on the surface of personnel whether they be clothed or not. The document is applicable only to that type of equipment where the user stays at the monitor. It is not applicable to the user passes quickly through the monitor. It is also not applicable to any peripheral equipment which may be associated with a particular type of equipment such as small article monitors. Probes (friskers) for measuring clothes or body by the person under monitoring or someone else are included in this document.

This document defines the structure of a standardized digital representation of an asset, called Asset Administration Shell. The Asset Administration Shell gives uniform access to information and services. The purpose of the Asset Administration Shell is to enable two or more software applications to exchange information and to mutually use the information that has been exchanged in a trusted and secure way. This document focusses on Asset Administration Shells representing assets of manufacturing enterprises including products produced by those enterprises and the full hierarchy of industrial equipment. It defines the related structures, information, and services. The Asset Administration Shell applies to: - any type of industrial process (discrete manufacturing, continuous process, batch process, hybrid production); - any industrial sector applying industrial-process measurement, control and automation; - the entire life cycle of assets from idea to end of life treatment; - assets which are physical, digital, or intangible entities.

This part of IEC 62321 specifies two different techniques for the determination of TCEP tris(2-chloroethyl) phosphate (TCEP) in plastics, the GC-MS or LC-MS method; both of which are suitable for quantitative analysis. These two techniques have been evaluated for use with polyurethane, Polyvinyl chloride and polyethylene materials containing TCEP between 200 mg/kg to 2 000 mg/kg. Use of the methods escribed in International Standard for other polymers and concentration ranges has not been specifically evaluated. These test methods do not apply to plastics materials having a processing temperature higher than 230 ℃. NOTE TCEP starts thermal decomposition at approximately 230 ℃. Polymer types which have a processing temperature into shapes of plastics (e.g. pellets, moulded parts, or sheets etc.) not exceeding the decomposition temperature can contain TCEP. Py-TD-GC-MS is another technique, suitable for the screening of TCEP in plastics (See Annex A).

IEC 60437:2023 specifies the procedure for a radio interference (RI) test carried out in a laboratory on clean and dry insulators at a frequency of 0,5 MHz or 1 MHz or, alternatively, at other frequencies between 0,5 MHz and 2 MHz. This document applies to insulators for use on AC or DC overhead power lines and overhead traction lines with a nominal voltage greater than 1 000 V. This third edition cancels and replaces the second edition published in 1997. This third edition cancels and replaces the second edition published in 1997. This edition includes the following significant technical changes with respect to the previous edition: a) Composite station post and composite hollow core station post insulators have been included; b) All paragraphs of Samples test were actualized; c) Sample test fast procedure was introduced.

IEC 62443-2:2023 specifies a comprehensive set of requirements for security-related processes that IACS service providers can offer to the asset owner during integration and maintenance activities of an Automation Solution. Because not all requirements apply to all industry groups and organizations, Subclause 4.1.4 provides for the development of "profiles" that allow for the subsetting of these requirements. Profiles are used to adapt this document to specific environments, including environments not based on an IACS. NOTE 1 The term "Automation Solution" is used as a proper noun (and therefore capitalized) in this document to prevent confusion with other uses of this term. Collectively, the security processes offered by an IACS service provider are referred to as its Security Program (SP) for IACS asset owners. In a related specification, IEC 62443-2-1 describes requirements for the Security Management System of the asset owner. NOTE 2 In general, these security capabilities are policy, procedure, practice and personnel related. Figure 1 illustrates the integration and maintenance security processes of the asset owner, service provider(s), and product supplier(s) of an IACS and their relationships to each other and to the Automation Solution. Some of the requirements of this document relating to the safety program are associated with security requirements described in IEC 62443-3-3 and IEC 62443-4-2. NOTE 3 The IACS is a combination of the Automation Solution and the organizational measures necessary for its design, deployment, operation, and maintenance. NOTE 4 Maintenance of legacy system with insufficient security technical capabilities, implementation of policies, processes and procedures can be addressed through risk mitigation.

IEC 60704-2-2:2023 is available as IEC 60704-2-2:2023 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.IEC 60704-2-2:2023 applies to electric fan heaters, designed for placing on the floor, table or counter, etc., or for mounting. This document does not apply to: - electric storage room heaters; - room humidifiers; - room dehumidifiers; - air cleaners; - heaters designed exclusively for industrial purposes. For determining and verifying noise emission values declared in product specifications, refer to IEC 60704-3:2019. This third edition cancels and replaces the second edition published in 2009. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: - alignment with the latest edition of IEC 60704-1:2021, - addition of several ISO standards, - revision of built-in-conditions, - addition of requirements on climatic conditions and on background noise. This part 2-2 is intended to be used in conjunction with the fourth edition of IEC 60704-1:2021, Household and similar electrical appliances - Test code for the determination of airborne acoustical noise - Part 1: General requirements. This part 2-2 supplements or modifies the corresponding clauses in IEC 60704-1:2021.

IEC 60143-4:2023 specifies the testing of thyristor controlled series capacitor (TCSC) installations used in series with transmission lines. This document also addresses issues that consider ratings for TCSC thyristor valve assemblies, capacitors, and reactors as well as TCSC control characteristics, protective features, cooling system and system operation. IEC 60143-4:2023 cancels and replaces the first edition published in 2010. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: a) thyristor valve testing requirements refer to IEC 62823; b) Formula (1) in Subclause 4.2 has been corrected; c) Hardware-in-the-loop (HIL) tests, Subclause 7.5.4, replaces previously specified real time protection and control system test with network simulator.

IEC 60749-5:2023 is available as IEC 60749-5:2023 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.IEC 60749-5:2023 provides a steady-state temperature and humidity bias life test to evaluate the reliability of non-hermetic packaged semiconductor devices in humid environments. This test method is considered destructive. This edition includes the following significant technical changes with respect to the previous edition: a) The specification of the test equipment is changed to require the need to minimize relative humidity gradients and maximize air flow between semiconductor devices under test; b) The specification of the test equipment fixtures is changed to require the avoidance of condensation on devices under test and on electrical fixtures connecting the devices to the test equipment; c) replacement of references to “virtual junction” with “die”.

IEC 62386-306:2023 is applicable to input devices that provide sensor information or measurements to the lighting control system. This document is only applicable to input devices complying with IEC 62386-103.