Industrial platinum resistance thermometers and platinum temperature sensors

IEC 60751:2008 specifies the requirements and temperature/resistance relationship for industrial platinum resistance temperature sensors later referred to as 'platinum resistors' or 'resistors' and industrial platinum resistance thermometers later referred to as 'thermometers' whose electrical resistance is a defined function of temperature. Values of temperature in this standard are in terms of the International Temperature Scale of 1990, ITS-90. Temperatures in degrees Celsius are denoted by the symbol t, except in Table 1 where the full nomenclature t90/°C is used. The standard covers resistors or thermometers for all or part of the temperature range 200 °C to +850 °C with different tolerance classes, which may cover restricted temperature ranges. This second edition cancels and replaces the first edition published in 1983, amendment 1 (1986) and amendment 2 (1995). It constitutes a technical revision. The significant technical changes with respect to the previous edition are as follows: While the temperature/resistance relationship in 4.2 remains unchanged, there are several changes in the other chapters. Most important are: tolerance classes follow a new scheme; tolerance acceptance test is included; hysteresis test is included; several changes in the individual tests; appendices are deleted.

Industrielle Platin-Widerstandsthermometer und Platin-Temperatursensoren

Thermomètres à résistance de platine industriels et capteurs thermométriques en platine

La CEI 60751:2008 spécifie les exigences et la relation température/résistance pour les capteurs à résistance de platine industriels, dénommés ci-après 'résistances de platine' ou 'résistances', et les thermomètres à résistance de platine industriels, dénommés ci-après 'thermomètres', dont la résistance électrique est une fonction définie de la température. Les valeurs de température données dans la présente norme sont exprimées en accord avec l'Echelle Internationale de Température de 1990, EIT-90, en degrés Celsius, et par le symbole t, à l'exception du Tableau 1 où l'expression t90/°C est utilisée. Elle couvre les résistances ou thermomètres pour toutes les parties de la gamme -200 °C à +850 °C avec différentes classes de tolérance, qui peuvent couvrir des domaines de températures limités. Cette deuxième édition annule et remplace la première édition parue en 1983, l'amendement1 (1986) et l'amendement 2 (1995). Cette édition constitue une révision technique. Par rapport à l'édition précédente, les modifications techniques majeures sont les suivantes: Alors que la relation entre la température et la résistance, donnée en 4.2 est inchangée, plusieurs modifications sont apportées dans les autres chapitres. Les plus importants sont: les classes de tolérance suivent un nouveau système; un essai d'acceptation de la tolérance est inclus; un essai d'hystérésis est inclus; plusieurs modifications sont apportées dans les essais individuels; des appendices sont supprimés.

Industrijski uporovni termometri in temperaturni senzorji iz platine (IEC 60751:2008 (EQV))

General Information

Status
Published
Publication Date
18-Sep-2008
Withdrawal Date
31-Jul-2011
Current Stage
6060 - Document made available - Publishing
Start Date
19-Sep-2008
Completion Date
19-Sep-2008

Relations

Buy Standard

Standard
EN 60751:2009
English language
24 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 60751:2009
01-januar-2009
1DGRPHãþD
SIST EN 60751:1998
SIST EN 60751:1998/A2:1998
Industrijski uporovni termometri in temperaturni senzorji iz platine (IEC
60751:2008 (EQV))
Industrial platinum resistance thermometers and platinum temperature sensors
Industrielle Platin-Widerstandsthermometer und Platin-Sensoren
Thermomètres à résistance de platine industriels et capteurs thermométriques en platine
Ta slovenski standard je istoveten z: EN 60751:2008
ICS:
17.200.20 Instrumenti za merjenje Temperature-measuring
temperature instruments
SIST EN 60751:2009 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 60751:2009

---------------------- Page: 2 ----------------------

SIST EN 60751:2009

EUROPEAN STANDARD
EN 60751

NORME EUROPÉENNE
September 2008
EUROPÄISCHE NORM

ICS 17.200.20 Supersedes EN 60751:1995 + A2:1995


English version


Industrial platinum resistance thermometers
and platinum temperature sensors
(IEC 60751:2008)


Thermomètres à résistance  Industrielle
de platine industriels Platin-Widerstandsthermometer
et capteurs thermométriques en platine und Platin-Sensoren
(CEI 60751:2008) (IEC 60751:2008)




This European Standard was approved by CENELEC on 2008-08-01. CENELEC members are bound to comply
with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard
the status of a national standard without any alteration.

Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the Central Secretariat or to any CENELEC member.

This European Standard exists in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CENELEC member into its own language and notified
to the Central Secretariat has the same status as the official versions.

CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Cyprus, the
Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.

CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung

Central Secretariat: rue de Stassart 35, B - 1050 Brussels


© 2008 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 60751:2008 E

---------------------- Page: 3 ----------------------

SIST EN 60751:2009
EN 60751:2008 – 2 –
Foreword
The text of document 65B/664/FDIS, future edition 2 of IEC 60751, prepared by SC 65B, Devices &
process analysis, of IEC TC 65, Industrial-process measurement, control and automation, was submitted
to the IEC-CENELEC parallel vote and was approved by CENELEC as EN 60751 on 2008-08-01.
This European Standard supersedes EN 60751:1995 + A2:1995.
The significant technical changes with respect to EN 60751:1995 are as follows:
While the temperature/resistance relationship in 4.2 remains unchanged, there are several changes in the
other chapters. Most important are:
– tolerance classes follow a new scheme;
– tolerance acceptance test is included;
– hysteresis test is included;
– several changes in the individual tests;
– appendices are deleted.
The following dates were fixed:
– latest date by which the EN has to be implemented
at national level by publication of an identical
national standard or by endorsement (dop) 2009-05-01
– latest date by which the national standards conflicting
with the EN have to be withdrawn (dow) 2011-08-01
Annex ZA has been added by CENELEC.
__________
Endorsement notice
The text of the International Standard IEC 60751:2008 was approved by CENELEC as a European
Standard without any modification.
__________

---------------------- Page: 4 ----------------------

SIST EN 60751:2009
– 3 – EN 60751:2008

Annex ZA
(normative)

Normative references to international publications
with their corresponding European publications

The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.

NOTE  When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD
applies.

Publication Year Title EN/HD Year

1) 2)
IEC 61152 - Dimensions of metal-sheathed thermometer EN 61152 1994
(mod) elements


1) 2)
IEC 61298-1 - Process me
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.