iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ISO

ISO 3016:2019

(Main)

Petroleum and related products from natural or synthetic sources — Determination of pour point

Petroleum and related products from natural or synthetic sources — Determination of pour point

This document specifies a method for the determination of the pour point of petroleum products. A separate procedure suitable for the determination of the lower pour point of fuel oils, heavy lubricant base stock, and products containing residual fuel components is also described. The procedure described in this document is not suitable for crude oils. NOTE There is equipment available that uses an automated procedure similar to the one described in this document. However, the precision thereof has not been established[1]. [1] ISO develops an automated test method standard.

Produits pétroliers et connexes d’origine naturelle ou synthétique — Détermination du point d'écoulement

Le présent document spécifie une méthode d'essai qui permet de déterminer le point d'écoulement des produits pétroliers. Une procédure distincte appropriée pour la détermination des points d'écoulement bas des fiouls, des bases lubrifiantes épaisses et des produits contenant des composés de fioul résiduel est également décrite. La procédure décrite dans ce document ne convient pas aux pétroles bruts. NOTE Un appareil est disponible sur le marché qui utilise une procédure automatisée semblable à celle décrite dans le présent document. Cependant, la fidélité n'a pas été établie dans ce cas[1]. [1] L?ISO élabore une norme de méthode d?essai automatisée.

General Information

Status
Published
Publication Date
24-Apr-2019
ICS
75.080 - Petroleum products in general
Technical Committee
ISO/TC 28 - Petroleum and related products, fuels and lubricants from natural or synthetic sources
Drafting Committee
ISO/TC 28/WG 27 - Stability, cleanliness and compatibility
Current Stage
9020 - International Standard under periodical review
Start Date
15-Apr-2024
Completion Date
15-Apr-2024
Ref Project

Relations

Revises
ISO 3016:1994 - Petroleum products — Determination of pour point
Effective Date
04-Mar-2017

Buy Standard

ISO 3016:2019 - Petroleum and related products from natural or synthetic sources -- Determination of pour pointISO 3016:2019 - Petroleum and related products from natural or synthetic sources -- Determination of pour point
PreviousNext
Standard
ISO 3016:2019 - Petroleum and related products from natural or synthetic sources -- Determination of pour point
English language
12 pages
sale 15% off
Preview
sale 15% off
Preview
ISO 3016:2019 - Produits pétroliers et connexes d’origine naturelle ou synthétique -- Détermination du point d'écoulementISO 3016:2019 - Produits pétroliers et connexes d’origine naturelle ou synthétique -- Détermination du point d'écoulement
PreviousNext
Standard
ISO 3016:2019 - Produits pétroliers et connexes d’origine naturelle ou synthétique -- Détermination du point d'écoulement
French language
13 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

INTERNATIONAL ISO
STANDARD 3016
Third edition
2019-04
Petroleum and related products
from natural or synthetic sources —
Determination of pour point
Produits pétroliers et connexes d’origine naturelle ou synthétique —
Détermination du point d'écoulement
Reference number
ISO 3016:2019(E)
©
ISO 2019

---------------------- Page: 1 ----------------------
ISO 3016:2019(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2019
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2019 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 3016:2019(E)

Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Principle . 2
5 Apparatus . 2
6 Sampling . 3
7 Procedure. 4
8 Expression of results . 6
9 Precision . 6
9.1 General . 6
9.2 Lubricating oils . 6
9.2.1 General. 6
9.2.2 Repeatability . 6
9.2.3 Reproducibility . 6
9.3 Middle distillate and residual fuels . 6
9.3.1 General. 6
9.3.2 Repeatability .
...

NORME ISO
INTERNATIONALE 3016
Troisième édition
2019-04
Produits pétroliers et connexes
d’origine naturelle ou synthétique —
Détermination du point d'écoulement
Petroleum and related products from natural or synthetic sources —
Determination of pour point
Numéro de référence
ISO 3016:2019(F)
©
ISO 2019

---------------------- Page: 1 ----------------------
ISO 3016:2019(F)

DOCUMENT PROTÉGÉ PAR COPYRIGHT
© ISO 2019
Tous droits réservés. Sauf prescription différente ou nécessité dans le contexte de sa mise en œuvre, aucune partie de cette
publication ne peut être reproduite ni utilisée sous quelque forme que ce soit et par aucun procédé, électronique ou mécanique,
y compris la photocopie, ou la diffusion sur l’internet ou sur un intranet, sans autorisation écrite préalable. Une autorisation peut
être demandée à l’ISO à l’adresse ci-après ou au comité membre de l’ISO dans le pays du demandeur.
ISO copyright office
Case postale 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Genève
Tél.: +41 22 749 01 11
Fax: +41 22 749 09 47
E-mail: copyright@iso.org
Web: www.iso.org
Publié en Suisse
ii © ISO 2019 – Tous droits réservés

---------------------- Page: 2 ----------------------
ISO 3016:2019(F)

Sommaire Page
Avant-Propos.iv
1 Domaine d'application . 1
2 Références normatives . 1
3 Termes et définitions . 1
4 Principe . 2
5 Appareillage . 2
6 Échantillonnage . 3
7 Mode opératoire. 4
8 Expression des résultats. 6
9 Fidélité . 6
9.1 Généralités . 6
9.2 Huiles lubrifiantes . 6
9.2.1 Généralités . 6
9.2.2 Répétabilité . 6
9.2.3 Reproductibilité . 7
9.3 Distillats moyens et fiouls résiduels . 7
9.3.1 Généralités . 7
9.3.2 Répétabilité . 7
9.3.3 Reproductibilité .
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ISO
ISO 18335:2024(Main)
Petroleum products and related products — Determination of kinematic viscosity by calculation from the measured dynamic viscosity and density – Method by constant pressure viscometer

This document specifies a procedure for determining dynamic viscosity, η, and density, ρ, for the calculation of kinematic viscosity, ν, of middle distillate fuels, fatty acid methyl ester fuels (FAME) and mixtures thereof, up to 60 % with middle distillate fuels, and lubricating oils (e.g. base oils, formulated oils), and synthetics, using a constant pressure viscometer. The range of kinematic viscosities covered in this test method is from 0,5 mm2/s to 2 000 mm2/s, with precision at 40 °C from 1,0 mm2/s to 1 286 mm2/s, and precision at 100 °C from 3,0 mm2/s to 157 mm2/s. The result obtained using the procedure described in this document depends on the rheological behaviour of the sample. This document is predominantly applicable to liquids whose shear stress and shear rate are proportional (Newtonian flow behaviour). However, if the viscosity changes significantly with the shear rate, comparison with other measuring methods is only permissible at similar shear rates.

  • Standard
    6 pages
    English language
    sale 15% off
  • Standard
    7 pages
    French language
    sale 15% off
ISO
ISO 4259-5:2023(Main)
Petroleum and related products — Precision of measurement methods and results — Part 5: Statistical assessment of agreement between two different measurement methods that claim to measure the same property

This document specifies statistical methodology for assessing the expected agreement between two test methods that purport to measure the same property of a material, and for deciding if a simple linear bias correction can further improve the expected agreement. This document is applicable for analytical methods which measure quantitative properties of petroleum or petroleum products resulting from a multi-sample-multi-lab study (MSMLS). These types of studies include but are not limited to interlaboratory studies (ILS) meeting the requirements of ISO 4259-1 or equivalent, and proficiency testing programmes (PTP) meeting the requirements of ISO 4259-3 or equivalent. The methodology specified in this document establishes the limiting value for the difference between two results where each result is obtained by a different operator using different apparatus and two methods X and Y, respectively, on identical material. One of the methods (X or Y) has been appropriately bias-corrected to agree with the other in accordance with this practice. This limit is designated as the between-methods reproducibility. This value is expected to be exceeded with a probability of 5 % under the correct and normal operation of both test methods due to random variation. NOTE Further conditions for application of this methodology are given in 5.1 and 5.2.

  • Standard
    48 pages
    English language
    sale 15% off
  • Standard
    50 pages
    French language
    sale 15% off
ISO
ISO 3104:2023(Main)
Petroleum products — Transparent and opaque liquids — Determination of kinematic viscosity and calculation of dynamic viscosity

This document specifies Procedure A, using manual glass viscometers, and Procedure B, using glass capillary viscometers in an automated assembly, for the determination of the kinematic viscosity, ν, of both transparent and opaque products. The scope includes liquid petroleum products, fatty acid methyl ester (FAME), paraffinic diesel, hydrotreated vegetable oil (HVO), gas to liquid (GTL) and biofuel diesel mixtures up to 50 % FAME. The kinematic viscosity is determined by measuring the time for a volume of liquid to flow under gravity through a calibrated glass capillary viscometer. The dynamic viscosity, η, is obtained by multiplying the measured kinematic viscosity by the density, ρ, of the liquid. The range of kinematic viscosities covered in this test method is from 0,2 mm2/s to 300 000 mm2/s over the temperature range –20 °C to +150 °C. NOTE The result obtained from this document is dependent upon the behaviour of the sample and is intended for application to liquids for which primarily the shear stress and shear rates are proportional (Newtonian flow behaviour). If, however, the viscosity varies significantly with the rate of shear, different results can be obtained from viscometers of different capillary diameters. The procedure and precision values for residual fuel oils, which under some conditions exhibit non-Newtonian behaviour, have been included.

  • Standard
    25 pages
    English language
    sale 15% off
  • Standard
    27 pages
    French language
    sale 15% off
ISO
ISO/TS 23877-1:2023(Main)
Petroleum and related products from natural or synthetic sources — Determination of pour point — Part 1: Automated step-wise cooling method

This document specifies a method for determining the pour point of petroleum products by means of automated equipment, in which movement of the test specimen is detected using a step-wise cooling technique. A separate procedure suitable for the determination of the lower pour point of fuel oils, heavy lubricant base stock, and products containing residual fuel components is also described. The procedure described in this document is not suitable for crude oils. Test results from this method are determined in 3 °C testing intervals. NOTE Some equipment can also generate results at 1 °C testing intervals, which is an acceptable alternative procedure, but for which precision and bias have not been determined.

  • Technical specification
    10 pages
    English language
    sale 15% off
ISO
ISO 3679:2022(Main)
Determination of flash point – Method for flash no-flash and flash point by small scale closed cup tester

This document describes three procedures (A, B and C) covering determinations of flash no-flash and flash point. Rapid equilibrium procedures A and B are applicable to flash no-flash and flash point tests of paints, including water-borne paints, varnishes, binders for paints and varnishes, adhesives, solvents, petroleum products including aviation turbine, diesel and kerosene fuels, fatty acid methyl esters and related products over the temperature range –30 °C to 300 °C. The rapid equilibrium procedures are used to determine whether a product will or will not flash at a specified temperature (flash no-flash procedure A) or the flash point of a sample (procedure B). When used in conjunction with the flash detector (A.1.6), this document is also suitable to determine the flash point of fatty acid methyl esters (FAME). The validity of the precision is given in Table 2. Non-equilibrium procedure C is applicable to petroleum products including aviation turbine, diesel and kerosine fuels, and related petroleum products, over the temperature range –20 °C to 300 °C. The non-equilibrium procedure is automated to determine the flash point. Precision has been determined over the range 40 °C to 135 °C. For specifications and regulations, procedures A or B are routinely used (see 10.1.1).

  • Standard
    27 pages
    English language
    sale 15% off
  • Standard
    28 pages
    French language
    sale 15% off
  • Standard
    28 pages
    French language
    sale 15% off
ISO
ISO 13736:2021/Amd 1:2022(Amendment)
Determination of flash point — Abel closed-cup method — Amendment 1: Bias statement update
  • Standard
    1 page
    English language
    sale 15% off
  • Standard
    2 pages
    French language
    sale 15% off
  • Standard
    2 pages
    French language
    sale 15% off
ISO
ISO 4259-4:2021(Main)
Petroleum and related products — Precision of measurement methods and results — Part 4: Use of statistical control charts to validate 'in-statistical-control' status for the execution of a standard test method in a single laboratory

This document specifies the process and methodology for the construction, operation, and maintenance of statistical control charts to assess if a laboratory's execution of a standard test method is in-statistical-control and how to establish and validate the 'in-statistical-control' status. It specifies control charts that are most appropriate for ISO/TC 28 test methods where the dominant common cause variation is associated with the long term, multiple operator conditions. The control charts specified for determination of in-statistical-control are: individual (I), moving range of 2 (MR2), and either the exponentially weighted moving average (EWMA) or zone-based run rules [similar to Western Electric (WE) run rules[3]] as sensitivity enhancement strategy to support the I-chart. The procedures in this document have been primarily designed for numerical results obtained from testing of control samples prepared from a homogenous source of petroleum and related products in a manner that preserves the homogeneity of properties of interest between control samples. If the test method permits, a certified reference material (CRM) sample is used as a control sample provided the sample composition is representative of the material being tested and is not a pure compound; if this is done then the laboratory best establishes its own mean for the CRM sample. This document is applicable to properties of interest that are (known to be) stable over time, and for data sets with sufficient resolution to support validation of the assumption that the data distribution can be approximately represented by the normal (Gaussian) model. Mitigating strategies are suggested for situations where the assumption cannot be validated.

  • Standard
    36 pages
    English language
    sale 15% off
  • Standard
    36 pages
    English language
    sale 15% off
  • Standard
    36 pages
    English language
    sale 15% off
  • Standard
    38 pages
    French language
    sale 15% off
  • Standard
    38 pages
    French language
    sale 15% off
  • Standard
    38 pages
    French language
    sale 15% off
ISO
ISO 20884:2019/Amd 1:2021(Amendment)
Petroleum products — Determination of sulfur content of automotive fuels — Wavelength-dispersive X-ray fluorescence spectrometry — Amendment 1: Addition of the SSD detector to the Monochromatic excitation part of Table 1
  • Standard
    1 page
    English language
    sale 15% off
  • Standard
    1 page
    French language
    sale 15% off
ISO
ISO 22854:2021(Main)
Liquid petroleum products — Determination of hydrocarbon types and oxygenates in automotive-motor gasoline and in ethanol (E85) automotive fuel — Multidimensional gas chromatography method

This document specifies the gas chromatographic (GC) method for the determination of saturated, olefinic and aromatic hydrocarbons in automotive motor gasoline and ethanol (E85) automotive fuel. Additionally, the benzene and toluene content, oxygenated compounds and the total oxygen content can be determined. NOTE 1 For the purposes of this document, the terms % (m/m) and % (V/V) are used to represent respectively the mass fraction, w, and the volume fraction, φ. This document defines two procedures, A and B. Procedure A is applicable to automotive motor gasoline with total aromatics of 19,32 % (V/V) up to 46,29 % (V/V); total olefins from 0,40 % (V/V) up to 26,85 % (V/V); oxygenates from 0,61 % (V/V) up to 9,85 % (V/V); oxygen content from 1,50 % (m/m) to 12,32 % (m/m); benzene content from 0,38 % (V/V) up to 1,98 % (V/V) and toluene content from 5,85 % (V/V) up to 31,65 % (V/V). The method has also been tested for individual oxygenates. A precision has been determined for a total volume of methanol from 1,05 % (V/V) up to 16,96 % (V/V); a total volume of ethanol from 0,50 % (V/V) up to 17,86 % (V/V); a total volume of MTBE from 0,99 % (V/V) up to 15,70 % (V/V), a total volume of ETBE from 0,99 % (V/V) up to 15,49 % (V/V), a total volume of TAME from 0,99 % (V/V) up to 5,92 % (V/V), and a total volume of TAEE from 0,98 % (V/V) up to 15,59 % (V/V). Although this test method can be used to determine higher-olefin contents of up to 50 % (V/V), the precision for olefins was tested only in the range from 0,40 % (V/V) to 26,85 % (V/V). Although specifically developed for the analysis of automotive motor gasoline that contains oxygenates, this test method can also be applied to other hydrocarbon streams having similar boiling ranges, such as naphthas and reformates. NOTE 2 For Procedure A, applicability of this document has also been verified for the determination of n-propanol, acetone, and di-isopropyl ether (DIPE). However, no precision data have been determined for these compounds. Procedure B describes the analysis of oxygenated groups (ethanol, methanol, ethers, C3 – C5 alcohols) in ethanol (E85) automotive fuel containing ethanol between 50 % (V/V) and 85 % (V/V). The gasoline is diluted with an oxygenate-free component to lower the ethanol content to a value below 20 % (V/V) before the analysis by GC. The sample can be fully analysed including hydrocarbons. Precision data for the diluted sample are only available for the oxygenated groups. NOTE 3 For Procedure B, the precision can be used for an ethanol fraction from about 50 % up to 85 % (V/V). For the ether fraction, the precision as specified in Table 6 can be used for samples containing at least 11 % (V/V) of ethers. For the higher alcohol fraction, too few data were obtained to derive a full precision statement and the data presented in Table 6 are therefore only indicative. NOTE 4 An overlap between C9 and C10 aromatics can occur. However, the total is accurate. Isopropyl benzene is resolved from the C8 aromatics and is included with the other C9 aromatics.

  • Standard
    21 pages
    English language
    sale 15% off
  • Standard
    22 pages
    French language
    sale 15% off
ISO
ISO 3837:1993/Amd 1:2021(Amendment)
Liquid petroleum products — Determination of hydrocarbon types — Fluorescent indicator adsorption method — Amendment 1
  • Standard
    1 page
    English language
    sale 15% off