Plastics piping systems for hot and cold water installations — Polyethylene of raised temperature resistance (PE-RT) — Part 5: Fitness for purpose of the system

ISO 22391-5:2009 specifies the characteristics of the fitness for purpose of piping systems made of polyethylene of raised temperature resistance (PE-RT), Type I and polyethylene of raised temperature resistance (PE-RT), Type II, intended to be used for hot and cold water installations within buildings for the conveyance of water, whether or not the water is intended for human consumption (domestic systems) and for heating systems, under the design pressures and temperatures appropriate to the class of application according to ISO 22391-1. ISO 22391-5:2009 covers a range of service conditions (classes of application), design pressures and pipe dimension classes, and also specifies test parameters and test methods. In conjunction with the other parts of ISO 22391, it is applicable to PE-RT pipes, fittings, their joints, and to joints having components of PE-RT as well as of other plastics and non-plastics materials, respectively, used for hot and cold water installations.

Systèmes de canalisations en plastique pour les installations d'eau chaude et froide — Polyéthylène de meilleure résistance à la température (PE-RT) — Partie 5: Aptitude à l'emploi du système

L'ISO 22391-5:2009 spécifie les caractéristiques d'aptitude à l'emploi des systèmes de canalisations en polyéthylène de meilleure résistance à la température (PE‑RT), Type I, et en polyéthylène de meilleure résistance à la température (PE‑RT), Type II, destinés aux installations d'eau chaude et froide à l'intérieur des bâtiments ainsi qu'au transport de l'eau, destinée ou non à la consommation humaine (systèmes domestiques) et aux installations de chauffage, à des pressions et des températures de service spécifiées correspondant à la classe d'application conformément à l'ISO 22391‑1. L'ISO 22391-5:2009 couvre une gamme de conditions de service (classes d'application), de pressions de service et de classes de dimension du tube, et spécifie également les paramètres et les méthodes d'essai. Lorsqu'elle est utilisée conjointement avec les autres parties de l'ISO 22391, elle s'applique respectivement aux tubes PE‑RT, aux raccords, à leurs assemblages et aux assemblages ayant des composants de PE‑RT, ainsi qu'à d'autres matériaux, plastiques ou non plastiques, utilisés pour les installations d'eau chaude et froide.

General Information

Status
Published
Publication Date
23-Nov-2009
Current Stage
9093 - International Standard confirmed
Completion Date
09-Oct-2019
Ref Project

Relations

Buy Standard

Standard
ISO 22391-5:2009
English language
12 pages
sale 15% off
Preview
sale 15% off
Preview
Standard
ISO 22391-5:2009 - Plastics piping systems for hot and cold water installations -- Polyethylene of raised temperature resistance (PE-RT)
English language
8 pages
sale 15% off
Preview
sale 15% off
Preview
Standard
ISO 22391-5:2009 - Systemes de canalisations en plastique pour les installations d'eau chaude et froide -- Polyéthylene de meilleure résistance a la température (PE-RT)
French language
9 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

МЕЖДУНАРОДНЫЙ ISO
СТАНДАРТ 22391-5
Второе издание
2009-12-01

Системы пластмассовых
трубопроводов для горячего и
холодного водоснабжения.
Полиэтилен повышенной
термостойкости (PE-RT).
Часть 5.
Соответствие системы назначению
Plastics piping systems for hot and cold water installations –
Polyethylene raised temperature resistance (PE-RT) –
Part 5: Fitness for purpose of the system



Ответственность за подготовку русской версии несёт GOST R
(Российская Федерация) в соответствии со статьёй 18.1 Устава ISO
Ссылочный номер
ISO 22391-5:2009(R)
©
ISO 2009

---------------------- Page: 1 ----------------------
ISO 22391-5:2009(R)
Отказ от ответственности при работе в PDF
Настоящий файл PDF может содержать интегрированные шрифты. В соответствии с условиями лицензирования, принятыми
фирмой Adobe, этот файл можно распечатать или вывести на экран, но его нельзя изменить, пока не будет получена
лицензия на загрузку интегрированных шрифтов в компьютер, на котором ведется редактирование. В случае загрузки
настоящего файла заинтересованные стороны принимают на себя ответственность за соблюдение лицензионных условий
фирмы Adobe. Центральный секретариат ISO не несет никакой ответственности в этом отношении.
Adobe − торговый знак фирмы Adobe Systems Incorporated.
Подробности, относящиеся к программным продуктам, использованным для создания настоящего файла PDF, можно найти в
рубрике General Info файла; параметры создания PDF были оптимизированы для печати. Были приняты во внимание все
меры предосторожности с тем, чтобы обеспечить пригодность настоящего файла для использования комитетами-членами
ISO. В редких случаях возникновения проблемы, связанной со сказанным выше, просьба проинформировать Центральный
секретариат по адресу, приведенному ниже.


ДОКУМЕНТ ЗАЩИЩЁН АВТОРСКИМ ПРАВОМ


©  ISO 2009
Все права сохраняются. Если не указано иное, никакую часть настоящей публикации нельзя копировать или использовать в
какой-либо форме или каким-либо электронным или механическим способом, включая фотокопии и микрофильмы, без
предварительного письменного согласия ISO по адресу, указанному ниже, или членов ISO в стране регистрации пребывания.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Опубликовано в Швейцарии

ii © ISO 2009 – Все права сохраняются

---------------------- Page: 2 ----------------------
ISO 22391-5:2009(R)
Содержание Страница
Предисловие .iv
Введение .v
1 Область применения .1
2 Нормативные ссылки .1
3 Термины, определения, символы и аббревиатуры .2
4 Соответствие назначению соединений и систем трубопроводов .2
4.1 Общие положения .2
4.2 Испытание на стойкость к внутреннему давлению .3
4.3 Испытание на изгиб .5
4.4 Сопротивление вытягиванию.6
4.5 Испытание на воздействие циклического изменения температуры .7
4.6 Испытание на циклическое изменение давления.8
4.7 Испытание на герметичность при разрежении .9
Библиография.10

© ISO 2009 – Все права сохраняются iii

---------------------- Page: 3 ----------------------
ISO 22391-5:2009(R)
Предисловие
Международная организация по стандартизации (ISO) является всемирной федерацией национальных
организаций по стандартизации (комитетов-членов ISO). Разработка международных стандартов
обычно осуществляется техническими комитетами ISO. Каждый комитет-член, заинтересованный в
деятельности, для которой был создан технический комитет, имеет право быть представленным в этом
комитете. Международные правительственные и неправительственные организации, имеющие связи с
ISO, также принимают участие в работах. ISO работает в тесном сотрудничестве с Международной
электротехнической комиссией (IEC) по всем вопросам стандартизации в области электротехники.
Международные стандарты разрабатываются в соответствии с правилами, установленными в
Директивах ISO/IEC, Часть 2.
Основная задача технических комитетов состоит в подготовке международных стандартов. Проекты
международных стандартов, одобренные техническими комитетами, рассылаются комитетам-членам
на голосование. Их опубликование в качестве международных стандартов требует одобрения, по
меньшей мере, 75 % комитетов-членов, принимающих участие в голосовании.
Следует иметь в виду, что некоторые элементы этого документа могут быть объектом патентных прав.
ISO не должен нести ответственность за идентификацию какого-либо одного или всех патентных прав.
ISO 22391-5 был подготовлен Техническим комитетом ISO/TC 138, Пластмассовые трубы, фитинги и
клапаны для транспортировки жидкостей, Подкомитетом SC 2, Пластмассовые трубы и фитинги
для водоснабжения.
Настоящее второе издание отменяет и заменяет первое издание (ISO 22391-5:2007), которое
распространялось только на материал PE-RT (именуемый Тип I), и расширяет его до описания
материалов PE-RT типа I и типа II.
1)
ISO 22391 состоит из следующих частей под общим названием Системы пластмассовых
трубопроводов для горячего и холодного водоснабжения⎯ Полиэтилен повышенной
термостойкости (PE-RT):
⎯ Часть 1. Общие положения
⎯ Часть 2. Трубы
⎯ Часть 3. Фитинги
⎯ Часть 5. Соответствие системы назначению


1) Настоящая система стандартов не включает в себя часть 4: Вспомогательное оборудование или часть 6:
Руководство по монтажу оборудования. По вспомогательному оборудованию можно использовать специальные
стандарты. Руководство по монтажу пластмассовых систем трубопроводов, изготовленных из различных
материалов и предназначенных для горячего и холодного водоснабжения, приведено в ENV 12108.
iv © ISO 2009 – Все права сохраняются

---------------------- Page: 4 ----------------------
ISO 22391-5:2009(R)
Введение
Входящая в систему стандартов стандарт Часть 5 устанавливает требования к системам
трубопроводов и их составным частям, изготовленным из полиэтилена повышенной термостойкости
(PE-RT). Системы трубопроводов предназначены для применения в установках горячего и холодного
водоснабжения.
В отношении потенциальной возможности отрицательного влияния рассматриваемых в ISO 22391
изделий на качество воды, предназначенной для потребления людьми, необходимо учесть
следующее:
a) Настоящая часть ISO 22391 не дает никакой информации, определяющей, могут или нет эти
изделия использоваться без ограничений.
b) Существующие национальные правила, касающиеся использования и/или характеристик этих
изделий, остаются в силе.
Настоящая часть ISO 22391 устанавливает основные характеристики систем пластмассовых
трубопроводов. На момент опубликования настоящей части ISO 22391 существовала следующая
серия системы стандартов для систем трубопроводов из других пластических материалов,
используемых для аналогичных практических задач:
ISO 15874 (все части), Системы пластмассовых трубопроводов для горячего и холодного
водоснабжения. Полипропилен (РР)
ISO 15875 (все части), Системы пластмассовых трубопроводов для горячего и холодного
водоснабжения. Сетчатый полиэтилен (РE-X)
ISO 15876 (все части), Системы пластмассовых трубопроводов для горячего и холодного
водоснабжения. Полибутилен (PB)
ISO 15877 (все части), Системы пластмассовых трубопроводов для горячего и холодного
водоснабжения. Хлорированный поливинилхлорид (PVC-C)


© ISO 2009 – Все права сохраняются v

---------------------- Page: 5 ----------------------
МЕЖДУНАРОДНЫЙ СТАНДАРТ ISO 22391-5:2009(R)

Системы пластмассовых трубопроводов для горячего и
холодного водоснабжения. Полиэтилен повышенной
термостойкости (PE-RT).
Часть 5.
Соответствие системы назначению
1 Область применения
Настоящая часть ISO 22391 устанавливает основные характеристики систем трубопроводов,
изготовленных из
⎯ полиэтилена повышенной термостойкости (PE-RT), типа I и
⎯ полиэтилена повышенной термостойкости (PE-RT), типа II,
предназначенных для горячего и холодного водоснабжения в зданиях, независимо от того,
предназначается вода для потребления людьми (система питьевого водоснабжения) или для систем
отопления при установленных проектных давлениях и температурах в соответствии с классом
эксплуатации согласно ISO 22391-1.
Настоящая часть ISO 22391 охватывает некоторый диапазон условий эксплуатации (классы
эксплуатации), проектные давления и классы размеров труб, а также устанавливает параметры
испытаний и методы испытаний. Вместе с другими частями ISO 22391 эта часть применима к трубам,
фитингам из PE-RT, их соединениям и соединениям, содержащим компоненты из PE-RT, также как из
других пластмассовых и непластмассовых материалов, предназначенных для горячего и холодного
водоснабжения.
Настоящая часть не применима к значениям проектной температуры, максимальной расчетной
температуры или температуры нарушения функционирования системы, превышающим установленные
в ISO 22391-1.
ПРИМЕЧАНИЕ Покупатель или представитель заказчика под свою ответственность осуществляют
соответствующий выбор из данных характеристик с учетом своих индивидуальных требований и соответствующих
национальных регламентов, практики монтажа или технических условий.
2 Нормативные ссылки
Следующие ссылочные документы обязательны для применения в настоящем документе. В случае
датированных ссылок применяются только цитированные издания. При недатированных ссылках
используется последнее издание ссылочного документа (включая все изменения).
ISO 1167-1, Термопластичные трубы, фитинги и узлы для передачи текучих сред. Определение
стойкости к внутреннему давлению. Часть 1: Общий метод
ISO 1167-2, Термопластичные трубы, фитинги и узлы для передачи текучих сред. Определение
стойкости к внутреннему давлению. Часть 2: Приготовление кусков труб к испытаниям
© ISO 2009 – Все права сохраняются 1

---------------------- Page: 6 ----------------------
ISO 22391-5:2009(R)
ISO 22391-1:2009, Системы пластмассовых трубопроводов для горячего и холодного
водоснабжения. Полиэтилен повышенной термостойкости (PE-RT). Часть 1: Общие положения
ISO 22391-2:2009, Системы пластмассовых трубопроводов для горячего и холодного
водоснабжения. Полиэтилен повышенной термостойкости (PE-RT).Часть 2: Трубы
EN 712, Системы трубопроводов из термопластов. Механические соединения, несущие торцевую
нагрузку, напорных трубопроводов с фитингами. Метод определения сопротивления вытягиванию
под действием постоянного продольного усилия
EN 713, Системы трубопроводов из термопластов. Механические соединения фитингов с
полиолефиновыми напорными трубами. Метод испытания на герметичность под внутренним
давлением соединений, подвергаемых изгибу
EN 12293, Системы пластмассовых трубопроводов. Трубы и фитинги из термопластов для
горячей и холодной воды. Метод определения стойкости узла в сборе к циклическому воздействию
температуры
EN 12294, Системы пластмассовых трубопроводов для горячей и холодной воды. Методы
испытаний герметичности в условиях вакуума
EN 12295, Системы пластмассовых трубопроводов. Трубы из термопластов и фитинги для
горячей и холодной воды. Методы испытаний прочности соединений при циклической перемене
давления
3 Термины, определения, символы и аббревиатуры
Применительно к настоящему документу используются термины, определени
...

INTERNATIONAL ISO
STANDARD 22391-5
Second edition
2009-12-01


Plastics piping systems for hot and cold
water installations — Polyethylene of
raised temperature resistance (PE-RT) —
Part 5:
Fitness for purpose of the system
Systèmes de canalisations en plastique pour les installations d'eau
chaude et froide — Polyéthylène de meilleure résistance à la
température (PE-RT) —
Partie 5: Aptitude à l'emploi du système




Reference number
ISO 22391-5:2009(E)
©
ISO 2009

---------------------- Page: 1 ----------------------
ISO 22391-5:2009(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.


COPYRIGHT PROTECTED DOCUMENT


©  ISO 2009
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland

ii © ISO 2009 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 22391-5:2009(E)
Contents Page
Foreword .iv
Introduction.v
1 Scope.1
2 Normative references.1
3 Terms, definitions, symbols and abbreviated terms .2
4 Fitness for purpose of joints and piping system .2
4.1 General .2
4.2 Internal pressure test.3
4.3 Bending test.4
4.4 Pull-out test.5
4.5 Thermal cycling test.6
4.6 Pressure cycling test .7
4.7 Leaktightness under vacuum test .7
Bibliography.8

© ISO 2009 – All rights reserved iii

---------------------- Page: 3 ----------------------
ISO 22391-5:2009(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 22391-5 was prepared by Technical Committee ISO/TC 138, Plastics pipes, fittings and valves for the
transport of fluids, Subcommittee SC 2, Plastics pipes and fittings for water supplies.
This second edition cancels and replaces the first edition (ISO 22391-5:2007), which is extended from only
dealing with PE-RT material (referred to as Type I) to cover PE-RT materials Type I and Type II.
1)
ISO 22391 consists of the following parts , under the general title Plastics piping systems for hot and cold
water installations — Polyethylene of raised temperature resistance (PE-RT):
⎯ Part 1: General
⎯ Part 2: Pipes
⎯ Part 3: Fittings
⎯ Part 5: Fitness for purpose of the system


1) This System Standard does not incorporate a Part 4: Ancillary equipment or a Part 6: Guidance for installation. For
ancillary equipment, separate standards can apply. Guidance for installation of plastics piping systems made from different
materials, intended to be used for hot and cold water installations, is covered by ENV 12108.
iv © ISO 2009 – All rights reserved

---------------------- Page: 4 ----------------------
ISO 22391-5:2009(E)
Introduction
The System Standard, of which this is Part 5, specifies the requirements for a piping system and its
components when made from polyethylene of raised temperature resistance (PE-RT). The piping system is
intended to be used for hot and cold water installations.
In respect of potential adverse effects on the quality of water intended for human consumption caused by the
products covered by ISO 22391, the following are relevant.
a) This part of ISO 22391 provides no information as to whether the products can be used without restriction.
b) Existing national regulations concerning the use and/or characteristics of the products remain in force.
This part of ISO 22391 specifies the characteristics of fitness for purpose of the system. At the date of
publication of this part of ISO 22391, System Standards Series for piping systems of other plastics materials
used for the same application are the following:
ISO 15874 (all parts), Plastics piping systems for hot and cold water installations — Polypropylene (PP)
ISO 15875 (all parts), Plastics piping systems for hot and cold water installations — Crosslinked polyethylene
(PE-X)
ISO 15876 (all parts), Plastics piping systems for hot and cold water installations — Polybutylene (PB)
ISO 15877 (all parts), Plastics piping systems for hot and cold water installations — Chlorinated
poly(vinyl chloride) (PVC-C)


© ISO 2009 – All rights reserved v

---------------------- Page: 5 ----------------------
INTERNATIONAL STANDARD ISO 22391-5:2009(E)

Plastics piping systems for hot and cold water installations —
Polyethylene of raised temperature resistance (PE-RT) —
Part 5:
Fitness for purpose of the system
1 Scope
This part of ISO 22391 specifies the characteristics of the fitness for purpose of piping systems made of
⎯ polyethylene of raised temperature resistance (PE-RT), Type I, and
⎯ polyethylene of raised temperature resistance (PE-RT), Type II,
intended to be used for hot and cold water installations within buildings for the conveyance of water, whether
or not the water is intended for human consumption (domestic systems) and for heating systems, under the
design pressures and temperatures appropriate to the class of application according to ISO 22391-1.
This part of ISO 22391 covers a range of service conditions (classes of application), design pressures and
pipe dimension classes, and also specifies test parameters and test methods. In conjunction with the other
parts of ISO 22391, it is applicable to PE-RT pipes, fittings, their joints, and to joints having components of
PE-RT as well as of other plastics and non-plastics materials, respectively, used for hot and cold water
installations.
It is not applicable to values of design temperature, maximum design temperature or malfunction temperature
in excess of those specified in ISO 22391-1.
NOTE It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects,
taking into account their particular requirements and any relevant national regulations and installation practices or codes.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
ISO 1167-1, Thermoplastics pipes, fittings and assemblies for the conveyance of fluids — Determination of
the resistance to internal pressure — Part 1: General method
ISO 1167-2, Thermoplastics pipes, fittings and assemblies for the conveyance of fluids — Determination of
the resistance to internal pressure — Part 2: Preparation of pipe test pieces
ISO 22391-1:2009, Plastics piping systems for hot and cold water installations — Polyethylene of raised
temperature resistance (PE-RT) — Part 1: General
ISO 22391-2:2009, Plastics piping systems for hot and cold water installations — Polyethylene of raised
temperature resistance (PE-RT) — Part 2: Pipes
© ISO 2009 – All rights reserved 1

---------------------- Page: 6 ----------------------
ISO 22391-5:2009(E)
EN 712, Thermoplastics piping systems — End-load bearing mechanical joints between pressure pipes and
fittings — Test method for resistance to pull-out under constant longitudinal force
EN 713, Plastics piping systems — Mechanical joints between fittings and polyolefin pressure pipes — Test
method for leaktightness under internal pressure of assemblies subjected to bending
EN 12293, Plastics piping systems —
...

NORME ISO
INTERNATIONALE 22391-5
Deuxième édition
2009-12-01



Systèmes de canalisations en plastique
pour les installations d'eau chaude et
froide — Polyéthylène de meilleure
résistance à la température (PE-RT) —
Partie 5:
Aptitude à l'emploi du système
Plastics piping systems for hot and cold water installations —
Polyethylene of raised temperature resistance (PE-RT) —
Part 5: Fitness for purpose of the system




Numéro de référence
ISO 22391-5:2009(F)
©
ISO 2009

---------------------- Page: 1 ----------------------
ISO 22391-5:2009(F)
PDF – Exonération de responsabilité
Le présent fichier PDF peut contenir des polices de caractères intégrées. Conformément aux conditions de licence d'Adobe, ce fichier
peut être imprimé ou visualisé, mais ne doit pas être modifié à moins que l'ordinateur employé à cet effet ne bénéficie d'une licence
autorisant l'utilisation de ces polices et que celles-ci y soient installées. Lors du téléchargement de ce fichier, les parties concernées
acceptent de fait la responsabilité de ne pas enfreindre les conditions de licence d'Adobe. Le Secrétariat central de l'ISO décline toute
responsabilité en la matière.
Adobe est une marque déposée d'Adobe Systems Incorporated.
Les détails relatifs aux produits logiciels utilisés pour la création du présent fichier PDF sont disponibles dans la rubrique General Info
du fichier; les paramètres de création PDF ont été optimisés pour l'impression. Toutes les mesures ont été prises pour garantir
l'exploitation de ce fichier par les comités membres de l'ISO. Dans le cas peu probable où surviendrait un problème d'utilisation,
veuillez en informer le Secrétariat central à l'adresse donnée ci-dessous.


DOCUMENT PROTÉGÉ PAR COPYRIGHT


©  ISO 2009
Droits de reproduction réservés. Sauf prescription différente, aucune partie de cette publication ne peut être reproduite ni utilisée sous
quelque forme que ce soit et par aucun procédé, électronique ou mécanique, y compris la photocopie et les microfilms, sans l'accord écrit
de l'ISO à l'adresse ci-après ou du comité membre de l'ISO dans le pays du demandeur.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Publié en Suisse

ii © ISO 2009 – Tous droits réservés

---------------------- Page: 2 ----------------------
ISO 22391-5:2009(F)
Sommaire Page
Avant-propos .iv
Introduction.v
1 Domaine d'application .1
2 Références normatives.1
3 Termes et définitions, symboles et abréviations .2
4 Aptitude à l'emploi des assemblages et du système de canalisations .2
4.1 Généralités .2
4.2 Essai de pression interne.3
4.3 Essai de courbure .5
4.4 Essai d'arrachement.6
4.5 Essai sous cycle thermique .6
4.6 Essai de pression cyclique.7
4.7 Essai d'étanchéité sous vide.8
Bibliographie.9

© ISO 2009 – Tous droits réservés iii

---------------------- Page: 3 ----------------------
ISO 22391-5:2009(F)
Avant-propos
L'ISO (Organisation internationale de normalisation) est une fédération mondiale d'organismes nationaux de
normalisation (comités membres de l'ISO). L'élaboration des Normes internationales est en général confiée
aux comités techniques de l'ISO. Chaque comité membre intéressé par une étude a le droit de faire partie du
comité technique créé à cet effet. Les organisations internationales, gouvernementales et non
gouvernementales, en liaison avec l'ISO participent également aux travaux. L'ISO collabore étroitement avec
la Commission électrotechnique internationale (CEI) en ce qui concerne la normalisation électrotechnique.
Les Normes internationales sont rédigées conformément aux règles données dans les Directives ISO/CEI,
Partie 2.
La tâche principale des comités techniques est d'élaborer les Normes internationales. Les projets de Normes
internationales adoptés par les comités techniques sont soumis aux comités membres pour vote. Leur
publication comme Normes internationales requiert l'approbation de 75 % au moins des comités membres
votants.
L'attention est appelée sur le fait que certains des éléments du présent document peuvent faire l'objet de
droits de propriété intellectuelle ou de droits analogues. L'ISO ne saurait être tenue pour responsable de ne
pas avoir identifié de tels droits de propriété et averti de leur existence.
L'ISO 22391-5 a été élaborée par le comité technique ISO/TC 138, Tubes, raccords et robinetterie en
matières plastiques pour le transport des fluides, sous-comité SC 2, Tubes et raccords en matières plastiques
pour adduction et distribution d'eau.
Cette deuxième édition annule et remplace la première édition (ISO 22391-5:2007), qui a été élargie pour
couvrir les matériaux en PE-RT de Type I et de Type II. La première édition ne traitant que du matériau en
PE-RT couramment désigné de Type I.
1)
L'ISO 22391 comprend les parties suivantes , présentées sous le titre général Systèmes de canalisations en
plastique pour les installations d'eau chaude et froide — Polyéthylène de meilleure résistance à la
température (PE-RT):
⎯ Partie 1: Généralités
⎯ Partie 2: Tubes
⎯ Partie 3: Raccords
⎯ Partie 5: Aptitude à l'emploi du système

1) La présente norme de système n'incorpore pas de Partie 4: Équipement annexe ou de Partie 6: Directives pour
l'installation. Pour l'équipement annexe, des normes séparées peuvent s'appliquer. Des directives pour l'installation des
systèmes de canalisations en plastique fabriqués à partir de différents matériaux, destinés aux installations d'eau chaude
et froide, sont traitées par l'ENV 12108.
iv © ISO 2009 – Tous droits réservés

---------------------- Page: 4 ----------------------
ISO 22391-5:2009(F)
Introduction
La norme de système, dont la présente partie est la Partie 5, spécifie les exigences relatives à un système de
canalisations et ses composants lorsqu'ils sont en polyéthylène de meilleure résistance à la température
(PE-RT). Le système de canalisations est destiné à être utilisé pour les installations d'eau chaude et froide.
Pour tenir compte des éventuels effets défavorables sur la qualité de l'eau destinée à la consommation
humaine, causés par les produits couverts par l'ISO 22391, les suivants sont pertinents:
a) la présente partie de l'ISO 22391 ne fournit aucune information sur la possibilité ou non d'utiliser les
produits sans restriction;
b) les réglementations nationales existantes relatives à l'utilisation et/ou aux caractéristiques des produits
restent en vigueur.
La présente partie de l'ISO 22391 spécifie les caractéristiques d'aptitude à l'emploi du système. À la date de
publication de la présente partie de l'ISO 22391, la série des normes de système pour les systèmes de
canalisations en d'autres matériaux plastiques utilisés pour la même application sont les suivantes:
ISO 15874 (toutes les parties), Systèmes de canalisations en plastique pour les installations d'eau chaude et
froide — Polypropylène (PP)
ISO 15875 (toutes les parties), Systèmes de canalisations en plastique pour les installations d'eau chaude et
froide — Polyéthylène réticulé (PE-X)
ISO 15876 (toutes les parties), Systèmes de canalisations en plastique pour les installations d'eau chaude et
froide — Polybutène (PB)
ISO 15877 (toutes les parties), Systèmes de canalisations en plastique pour les installations d'eau chaude et
froide — Poly(chlorure de vinyle) chloré (PVC-C)

© ISO 2009 – Tous droits réservés v

---------------------- Page: 5 ----------------------
NORME INTERNATIONALE ISO 22391-5:2009(F)

Systèmes de canalisations en plastique pour les installations
d'eau chaude et froide — Polyéthylène de meilleure résistance à
la température (PE-RT) —
Partie 5:
Aptitude à l'emploi du système
1 Domaine d'application
La présente partie de l'ISO 22391 spécifie les caractéristiques d'aptitude à l'emploi des systèmes de
canalisations en
⎯ polyéthylène de meilleure résistance à la température (PE-RT), Type I, et
⎯ polyéthylène de meilleure résistance à la température (PE-RT), Type II,
destinés aux installations d'eau chaude et froide à l'intérieur des bâtiments ainsi qu'au transport de l'eau,
destinée ou non à la consommation humaine (systèmes domestiques) et aux installations de chauffage, à des
pressions et des températures de service spécifiées correspondant à la classe d'application conformément à
l'ISO 22391-1.
La présente partie de l'ISO 22391 couvre une gamme de conditions de service (classes d'application), de
pressions de service et de classes de dimension du tube, et spécifie également les paramètres et les
méthodes d'essai. Lorsqu'elle est utilisée conjointement avec les autres parties de l'ISO 22391, elle s'applique
respectivement aux tubes PE-RT, aux raccords, à leurs assemblages et aux assemblages ayant des
composants de PE-RT, ainsi qu'à d'autres matériaux, plastiques ou non plastiques, utilisés pour les
installations d'eau chaude et froide.
Elle ne s'applique pas aux valeurs de température de service, de température maximale de service, ou de
température de dysfonctionnement qui dépassent celles spécifiées dans l'ISO 22391-1.
NOTE Il est de la responsabilité de l'acheteur ou du spécificateur de réaliser une sélection appropriée de ces aspects,
en tenant compte des exigences particulières et des réglementations nationales et pratiques ou codes d'installation
pertinents.
2 Références normatives
Les documents de référence suivants sont indispensables pour l'application du présent document. Pour les
références datées, seule l'édition citée s'applique. Pour les références non datées, la dernière édition du
document de référence s'applique (y compris les éventuels amendements).
ISO 1167-1, Tubes, raccords et assemblages en matières thermoplastiques pour le transport des fluides —
Détermination de la résistance à la pression interne — Partie 1: Méthode générale
ISO 1167-2, Tubes, raccords et assemblages en matières thermoplastiques pour le transport des fluides —
Détermination de la résistance à la pression interne — Partie 2: Préparation des éprouvettes tubulaires
© ISO 2009 – Tous droits réservés 1

---------------------- Page: 6 ----------------------
ISO 22391-5:2009(F)
ISO 22391-1:2009, Systèmes de canalisations en plastique pour les installations d'eau chaude et froide —
Polyéthylène de meilleure résistance à la température (PE-RT) — Partie 1: Généralités
ISO 22391-2:2009, Systèmes de canalisations en plastique pour les installations d'eau chaude et froide —
Polyéthylène de meilleure résistance à la température (PE-RT) — Partie 2: Tubes
EN 712, Systèmes de canalisations thermoplastiques — Assemblages mécaniques avec effet des fonds entre
tubes avec pression et raccords — Méthode d'essai de résistance à l'arrachement sous force constante
EN 713, Systèmes de canalisations plastiques — Assemblages mécaniques entre raccords et tubes en
polyoléfine avec pression — Essai d'étanchéité sous pression interne des assemblages soumis à une
courbure
EN 12293, Systèmes de canalisations en plastique — Tubes thermoplastiques et raccords pour installations
d'eau chaude et froide sous press
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.