Metallic and other inorganic coatings — Electroplated coatings of cadmium with supplementary treatments on iron or steel

ISO 2082:2017 specifies the requirements of electroplated coatings of cadmium with supplementary treatments on iron and steel. It includes information that is to be supplied by the purchaser to the electroplater, and describes coating requirements, including those for heat treatment before and after electroplating. It is not applicable to coatings applied - to sheet, strip or wire in the non-fabricated form, - to close-coiled springs, or - for purposes other than protective, intrinsic lubricity, ductility, electrical conductivity and low contact resistance use. ISO 2082:2017 does not specify requirements for the surface condition of the basis metal prior to electrodeposition with cadmium. The coating thickness that can be applied to threaded components can be limited by dimensional requirements, including class or fit. Additional information on corrosion resistance, rinsing and drying, processing parts in bulk and dyeing of chromate conversion coatings is given in Annex C.

Revêtements métalliques et autres revêtements inorganiques — Dépôts électrolytiques de cadmium avec traitements supplémentaires sur fer ou acier

L'ISO 2082:2017 spécifie les exigences relatives aux dépôts électrolytiques de cadmium accompagnés de traitements supplémentaires sur fer et acier. Elle inclut les informations à fournir par l'acheteur à l'électroplaste et décrit les exigences de revêtement, notamment celles relatives au traitement thermique avant et après dépôt électrolytique. Elle n'est pas applicable aux revêtements appliqués: - sur tôles, feuillards ou fils à l'état non façonné; - sur des ressorts à spirales serrées; - à des fins autres que la protection, l'aptitude intrinsèque à la lubrification, la ductilité, la conductivité électrique et la faible résistance de contact. L'ISO 2082:2017 ne spécifie pas d'exigence portant sur l'état de surface du métal de base avant dépôt électrolytique au cadmium. L'épaisseur du revêtement susceptible d'être appliqué sur les pièces filetées peut être limitée par des exigences dimensionnelles, y compris la classe ou l'ajustement. Des informations supplémentaires sur la résistance à la corrosion, le rinçage et le séchage, le traitement de pièces en vrac et la coloration de couches de conversion au chromate sont fournies dans l'Annexe C.

General Information

Status
Published
Publication Date
02-Aug-2017
Current Stage
9093 - International Standard confirmed
Completion Date
10-Oct-2023
Ref Project

Relations

Buy Standard

Standard
ISO 2082:2017 - Metallic and other inorganic coatings -- Electroplated coatings of cadmium with supplementary treatments on iron or steel
English language
13 pages
sale 15% off
Preview
sale 15% off
Preview
Standard
ISO 2082:2017 - Revetements métalliques et autres revetements inorganiques -- Dépôts électrolytiques de cadmium avec traitements supplémentaires sur fer ou acier
French language
13 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

INTERNATIONAL ISO
STANDARD 2082
Fourth edition
2017-07
Metallic and other inorganic
coatings — Electroplated coatings
of cadmium with supplementary
treatments on iron or steel
Revêtements métalliques et autres revêtements inorganiques —
Dépôts électrolytiques de cadmium avec traitements supplémentaires
sur fer ou acier
Reference number
ISO 2082:2017(E)
©
ISO 2017

---------------------- Page: 1 ----------------------
ISO 2082:2017(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2017, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2017 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 2082:2017(E)

Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms, definitions, abbreviated terms and symbols . 2
3.1 Terms and definitions . 2
3.2 Abbreviated terms . 2
3.3 Symbols . 2
4 Information to be supplied by the purchaser to the electroplater .3
4.1 Essential information . 3
4.2 Additional information . 3
5 Designation . 3
5.1 General . 3
5.2 Designation specification . 4
5.3 Designation of the basis material. 5
5.4 Designation of heat treatment requirements . 5
6 Requirements . 5
6.1 Appearance . 5
6.2 Thickness .
...

NORME ISO
INTERNATIONALE 2082
Quatrième édition
2017-07
Revêtements métalliques et autres
revêtements inorganiques — Dépôts
électrolytiques de cadmium avec
traitements supplémentaires sur fer
ou acier
Metallic and other inorganic coatings — Electroplated coatings of
cadmium with supplementary treatments on iron or steel
Numéro de référence
ISO 2082:2017(F)
©
ISO 2017

---------------------- Page: 1 ----------------------
ISO 2082:2017(F)

DOCUMENT PROTÉGÉ PAR COPYRIGHT
© ISO 2017, Publié en Suisse
Droits de reproduction réservés. Sauf indication contraire, aucune partie de cette publication ne peut être reproduite ni utilisée
sous quelque forme que ce soit et par aucun procédé, électronique ou mécanique, y compris la photocopie, l’affichage sur
l’internet ou sur un Intranet, sans autorisation écrite préalable. Les demandes d’autorisation peuvent être adressées à l’ISO à
l’adresse ci-après ou au comité membre de l’ISO dans le pays du demandeur.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2017 – Tous droits réservés

---------------------- Page: 2 ----------------------
ISO 2082:2017(F)

Sommaire Page
Avant-propos .iv
Introduction .v
1 Domaine d’application . 1
2 Références normatives . 1
3 Termes, définitions, termes abrégés et symboles . 2
3.1 Termes et définitions . 2
3.2 Termes abrégés . 2
3.3 Symboles . 3
4 Informations à fournir à l’électroplaste par l’acheteur . 3
4.1 Informations essentielles . 3
4.2 Informations complémentaires . 3
5 Désignation . 4
5.1 Généralités . 4
5.2 Spécification de désignation . 4
5.3 Désignation du matériau de base. 5
5.4 Désignation des exigences relatives au traitement thermique . 5
6 Exigences . 5
6.1 Aspect . . 5
6.2 Épaisseur .
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.