ISO/IEC 19772:2020

INTERNATIONAL ISO/IEC
STANDARD 19772
Second edition
2020-11
Information security — Authenticated
encryption
Sécurité de l'information — Chiffrement authentifié
Reference number
ISO/IEC 19772:2020(E)
©
ISO/IEC 2020

---------------------- Page: 1 ----------------------
ISO/IEC 19772:2020(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO/IEC 2020
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO/IEC 2020 – All rights reserved

---------------------- Page: 2 ----------------------
ISO/IEC 19772:2020(E)

Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Symbols and abbreviated terms . 3
5 Requirements . 4
6 Authenticated encryption mechanism 2 (key wrap) . 5
6.1 General . 5
6.2 Specific notation . 5
6.3 Specific requirements . 5
6.4 Encryption procedure . 5
6.5 Decryption procedure . 6
7 Authenticated encryption mechanism 3 (CCM) . 6
7.1 General . 6
7.2 Specific notation . 7
7.3 Specific requirements . 7
7.4 Encryption procedure . 7
7.5 Decryption procedure . 9
8 Authenticated encryption mechanism 4 (EAX) .10
8.1 General .10
8.2 Specific notation .10
8.3 Specific requirements .10
8.4 Definition of function M .10
8.5 Encryption procedure .11
8.6 Decryption procedure .11
9 Authenticated encryption mechanism 5 (encrypt-then-MAC) .12
9.1 General .12
9.2 Specific notation .12
9.3 Specific requirements .12
9.4 Encryption procedure .13
9.5 Decryption procedure .13
10 Authenticated encryption mechanism 6 (GCM) .14
10.1 General .14
10.2 Specific notation .14
10.3 Specific requirements .15
10.4 Definition of multiplication operation • .15
10.5 Definition of function G .15
10.6 Encryption procedure .16
10.7 Decryption procedure .16
Annex A (informative) Guidance on the use of the mechanisms .18
Annex B (informative) Numerical examples .21
Annex C (normative) Object identifiers .25
Bibliography .26
© ISO/IEC 2020 – All rights reserved iii

---------------------- Page: 3 ----------------------
ISO/IEC 19772:2020(E)

Foreword
ISO (the International Organization for Standardization) and IEC (the International Electrotechnical
Commission) form the specialized system for worldwide standardization. National bodies that
are members of ISO or IEC participate in the development of International Standards through
technical committees established by the respective organization to deal with particular fields of
technical activity. ISO and IEC technical committees collaborate in fields of mutual interest. Other
international organizations, governmental and non-governmental, in liaison with ISO and IEC, also
take part in the work.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for
the different types of document should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject
of patent rights. ISO and IEC shall not be held responsible for identifying any or all such patent
rights. Details of any patent rights identified during the development of the document will be in the
Introduction and/or on the ISO list of patent declarations received (see www .iso .org/ patents) or the IEC
list of patent declarations received (see http:// patents .iec .ch).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see www .iso .org/
iso/ foreword .html.
This document was prepared by Technical Committee ISO/IEC JTC 1, Information Technology,
Subcommittee SC 27, Information security, cybersecurity and privacy protection.
This second edition cancels and replaces the first edition (ISO/IEC 19772:2009) which has been
technically revised. It also incorporates the Technical Corrigendum ISO/IEC 19772:2009/Cor 1:2014.
The main changes compared to the previous edition are as follows:
— old Clause 6 has been removed following the deprecation of mechanism 1 (OCB 2.0);
— optional additional authenticated data has been included in mechanism 5.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www .iso .org/ members .html.
iv © ISO/IEC 2020 – All rights reserved

---------------------- Page: 4 ----------------------
ISO/IEC 19772:2020(E)

Introduction
When data is sent from one place to another, it is often necessary to protect it in some way while it is in
transit, e.g. against eavesdropping or unauthorized modification. Similarly, when data is stored in an
environment to which unauthorized parties can have access, it can be necessary to protect it.
If the confidentiality of the data needs to be protected, e.g. against eavesdropping, then one solution
is to use encryption, as specified in ISO/IEC 18033 (all parts) and ISO/IEC 10116. Alternatively,
if it is necessary to protect the data against modification, i.e. integrity protection, then message
authentication codes (MACs) as specified in ISO/IEC 9797 (all parts), or digital signatures as specified in
ISO/IEC 9796 (all parts) and ISO/IEC 14888 (all parts), can be used. If both confidentiality and integrity
protection are required, then one possibility is to use both encryption and a MAC or signature. While
these operations can be combined in many ways, not all combinations of such mechanisms provide
the same security guarantees. As a result, it is desirable to define in detail exactly how integrity and
confidentiality mechanisms should be combined to provide the optimum level of security. Moreover, in
some cases, significant efficiency gains can be obtained by defining a single method of processing the
data with the objective of providing both confidentiality and integrity protection.
In this document, authenticated encryption mechanisms are defined. These are methods for processing
data to provide both integrity and confidentiality protection. They typically involve either a specified
combination of a MAC computation and data encryption, or the use of an encryption algorithm in a
special way such that both integrity and confidentiality protection are provided.
The methods specified in this document have been designed to maximize the level of security and
provide efficient processing of data. Some of the techniques defined here have mathematical "proofs of
security", i.e. rigorous arguments supporting their soundness.
© ISO/IEC 2020 – All rights reserved v

---------------------- Page: 5 ----------------------
INTERNATIONAL STANDARD ISO/IEC 19772:2020(E)
Information security — Authenticated encryption
1 Scope
This document specifies five methods for authenticated encryption, i.e. defined ways of processing a
data string with the following security objectives:
— data confidentiality, i.e. protection against unauthorized disclosure of data;
— data integrity, i.e. protection that enables the recipient of data to verify that it has not been modified;
— data origin authentication, i.e. protection that enables the recipient of data to verify the identity of
the data originator.
All five methods specified in this document are based on a block cipher algorithm, and require the
originator and the recipient of the protected data to share a secret key for this block cipher.
Key management is outside the scope of this document. Key management techniques are defined in
ISO/IEC 11770 (all parts).
Four of the mechanisms in this document, namely mechanisms 3, 4, 5 (AAD variant only) and 6, allow
data to be authenticated which is not encrypted. That is, these mechanisms allow a data string that is
to be protected to be divided into two parts, D, the data string that is to be encrypted and integrity-
protected, and A (the additional authenticated data) that is integrity-protected but not encrypted. In all
cases, the string A can be empty.
NOTE Examples of types of data that can need to be sent in unencrypted form, but whose integrity is to be
protected, include addresses, port numbers, sequence numbers, protocol version numbers and other network
protocol fields that indicate how the plaintext is to be handled, forwarded or processed.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
ISO/IEC 9797 (all parts), Information technology — Security techniques — Message Authentication
Codes (MACs)
ISO/IEC 10116, Information technology — Security techniques — Modes of operation for an n-bit block cipher
ISO/IEC 18033-3, Information technology — Security techniques — Encryption algorithms — Part 3:
Block ciphers
3 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
— ISO Online browsing platform: available at https:// www .iso .org/ obp
— IEC Electropedia: available at http:// www .electropedia .org/
© ISO/IEC 2020 – All rights reserved 1

---------------------- Page: 6 ----------------------
ISO/IEC 19772:2020(E)

3.1
additional authenticated data
AAD
data that is integrity-protected but not encrypted by the authenticated encryption mechanism (3.3)
3.2
authenticated encryption
(reversible) transformation of data by a cryptographic algorithm to produce ciphertext (3.5) that
cannot be altered by an unauthorized entity without detection, i.e. it provides data confidentiality, data
integrity (3.6), and data origin authentication
3.3
authenticated encryption mechanism
cryptographic technique used to protect the confidentiality and guarantee the origin and integrity of
data, and which consists of two component processes: an encryption (3.8) algorithm and a decryption
(3.7) algorithm
3.4
block cipher
symmetric encryption system (3.15) with the property that the encryption (3.8) algorithm operates on a
block of plaintext (3.13), i.e. a string of bits of a defined length, to yield a block of ciphertext (3.5)
[SOURCE: ISO/IEC 18033-1:2015, 2.9]
3.5
ciphertext
data which has been transformed to hide its information content
[SOURCE: ISO/IEC 10116:2017, 3.2]
3.6
data integrity
property that data has not been altered or destroyed in an unauthorized manner
[SOURCE: ISO/IEC 9797-1:2011, 3.4]
3.7
decryption
reversal of a corresponding encryption (3.8)
[SOURCE: ISO/IEC 18033-1:2015, 2.16]
3.8
encryption
(reversible) transformation of data by a cryptographic algorithm to produce ciphertext (3.5), i.e., to hide
the information content of the data
[SOURCE: ISO/IEC 18033-1:2015, 2.21]
3.9
encryption system
cryptographic technique used to protect the confidentiality of data, and which consists of three
component processes: an encryption (3.8) algorithm, a decryption (3.7) algorithm, and a method for
generating keys (3.10)
[SOURCE: ISO/IEC 18033-1:2015, 2.23]
2 © ISO/IEC 2020 – All rights reserved

---------------------- Page: 7 ----------------------
ISO/IEC 19772:2020(E)

3.10
key
sequence of symbols that controls the operation of a cryptographic transformation (e.g. encipherment,
decipherment)
[SOURCE: ISO/IEC 18033-1:2015, 2.27]
3.11
message authentication code
MAC
string of bits which is the output of a MAC algorithm
[SOURCE: ISO/IEC 9797-1:2011, 3.9]
3.12
partition
process of dividing a string of bits of arbitrary length into a sequence of blocks, where the length of
each block is n bits, except for the final block which shall contain r bits, 0 < r ≤ n
3.13
plaintext
unencrypted information
[SOURCE: ISO/IEC 10116:2017, 3.11]
3.14
secret key
key (3.10) used with symmetric cryptographic techniques by a specified set of entities
[SOURCE: ISO/IEC 18033-1:2015, 2.33]
3.15
symmetric encryption system
encryption (3.8) system based on symmetric cryptographic techniques that uses the same secret key
(3.14) for both the encryption (3.8) and decryption (3.7) algorithms
[SOURCE: ISO/IEC 18033-1:2015, 2.40]
4 Symbols and abbreviated terms
A additional authenticated data
C authenticated-encrypted data string
D data string to which an authenticated encryption mechanism is to be applied
d block cipher decryption algorithm; d (Y) denotes the result of block cipher decrypting the n-bit
K
block Y using the secret key K
e block cipher encryption algorithm; e (X) denotes the result of block cipher encrypting the n-bit
K
block X using the secret key K
K secret block cipher key shared by the originator and recipient of the data to which the authenti-
cated encryption mechanism is to be applied
m number of blocks in the partitioned version of D
n block length (in bits) for a block cipher
t tag length (in bits)
© ISO/IEC 2020 – All rights reserved 3

---------------------- Page: 8 ----------------------
ISO/IEC 19772:2020(E)

i
0 block of i zero bits
i
1 block of i one bits
⊕ bit-wise exclusive-or of strings of bits (of the same bit-length)
|| concatenation of bit strings, i.e. if A and B are blocks of bits, then A||B is the block of bits obtained
by concatenating A and B in the order specified
# function converting a number into an a-bit block of bits
a
If k is an integer (0 ≤ k < 2 ), then # (k) is the a-bit block which, when regarded as the binary rep-
a
resentation of a number with the most significant bit on the left, equals k.
-1
# function converting a block of bits to a number
-1
If A is a block of bits, then # (A) is the unique non- negative integer whose binary representation
-1
is A. Hence, if A has n bits, then # (# (A)) = A.
n
X| left-truncation of the block of bits X
s
If X has bit-length greater than or equal to s, then X| is the s-bit block consisting of the left-most
s
s bits of X.
s
X| right-truncation of the block of bits X
s
If X has bit-length greater than or equal to s, then X| is the s- bit block consisting of the right-most
s bits of X.
X<<1 left shift of a block of bits X by one position
The rightmost bit of Y = X<<1 is always set to zero.
X>>1 right shift of a block of bits X by one position
The leftmost bit of Y = X>>1 is always set to zero.
len function taking a bit-string X as input, and which gives as output the number of bits in X
mod if a and b > 0 are integers, then a mod b denotes the unique integer c such that:
1) 0 ≤ c < b; and
2) a-c is an integer multiple of b.
5 Requirements
The authenticated encryption mechanisms specified in this document have the following requirements.
The originator and recipient of the data to which the authenticated encryption mechanism is to be
applied, shall:
a) agree on the use of a particular mechanism from those specified in this document;
b) agree on the use of a particular block cipher to be used with the mechanism (one of the block
ciphers standardized in ISO/IEC 18033-3 shall be used);
c) share a secret key K: in all mechanisms except for authenticated encryption mechanism 5, this shall
be a key for the selected block cipher, and in mechanism 5 it shall be a key used as input to a key
derivation procedure.
In addition, each mechanism has specific requirements listed immediately before the mechanism
description.
4 © ISO/IEC 2020 – All rights reserved

---------------------- Page: 9 ----------------------
ISO/IEC 19772:2020(E)

Annex A provides guidance on the use of the mechanisms defined in this document.
Annex B contains numerical examples of the operation of the mechanisms specified in this document.
Annex C provides the object identifiers which shall be used to identify the mechanisms defined in this
document.
6 Authenticated encryption mechanism 2 (key wrap)
6.1 General
This clause defines an authenticated encryption mechanism commonly known as key wrap.
NOTE 1 This scheme was originally designed for authenticated encryption of keys and associated information.
That is, it is designed for use with short data strings. However, the scheme can be used with arbitrary length data
67
strings (up to a maximum of around 2 bits), although it is not efficient for protecting long messages.
NOTE 2 This mode is known as AES key wrap when the AES block cipher is used, where AES stands for
advanced encryption standard, a block cipher algorithm specified in ISO/IEC 18033-3:2010. AES key wrap is also
specified in References [7] and [9].
6.2 Specific notation
For the purposes of the specification of this mechanism, the following symbols and notation apply:
C , C , …, C sequence of (m+1) 64-bit blocks obtained as the output of the authenticated encryp-
0 1 m
tion process
D , D , …, D sequence of m 64-bit blocks obtained by partitioning D, i.e. 64m = len(D)
1 2 m
R , R , …, R sequence of m 64-bit blocks computed during the encryption and decryption processes
1 2 m
Y 64-bit block used during the encryption and decryption processes
Z 128-bit block computed during the encryption and decryption processes
6.3 Specific requirements
The block cipher to be used with this mechanism shall be a 128-bit block cipher, i.e. it shall have n=128.
The data string D to be protected using this mechanism shall contain at least 128 bits and a multiple of
64 bits (i.e. the bit-length of D shall be 64m for some integer m > 1).
6.4 Encryption procedure
The originator shall perform the following steps to protect a data string D.
a) Partition D into a sequence of m 64-bit blocks D , D , …, D , so that D contains the first 64 bits of D,
1 2 m 1
D the next 64 bits, and so on.
2
b) Let Y be the 64-bit block having hexadecimal representation A6A6A6A6A6A6A6A6, i.e. in binary it
equals (10100110 10100110 … 10100110).
c) For i = 1, 2, …, m:
let R = D .
i i
d) For i = 1, 2, ., 6m, perform the following four steps:
1) Let Z = e ( Y || R );
K 1
© ISO/IEC 2020 – All rights reserved 5

---------------------- Page: 10 ----------------------
ISO/IEC 19772:2020(E)

2) Let Y = Z| ⊕ # (i);
64 64
3) For j = 1, 2, …, m-1:
let R = R ;
j j+1
64
4) Let R = Z| .
m
e) Let C = Y.
0
f) For i = 1, 2, …, m:
let C = R .
i i
The output of the above process, i.e. the authenticated-encrypted version of D, shall be the bit-string:
C = C || C || … || C
0 1 m
That is, a string of 64(m+1) bits, that is C contains precisely 64 bits more than D.
6.5 Decryption procedure
The recipient shall perform the following steps to decrypt and verify an authenticated-encrypted string C.
a) If len(C) is not a multiple of 64 or is less than 192, then halt and output INVALID.
b) Partition C into a sequence of m+1 64-bit blocks C , C , …, C , so that C contains the first 64 bits of
0 1 m 0
C, C the next 64 bits, and so on.
1
c) Let Y = C .
0
d) For i = 1, 2, …, m:
let R = C .
i i
e) For i = 6m, 6m-1, down to 1, perform the following four steps:
1) Let Z = d ( [Y ⊕ # (i)] || R );
K 64 m
2) Let Y = Z| ;
64
3) For j = m, m-1, …, 2:
let R = R ;
j j-1
64
4) Let R = Z| .
1
f) If Y = (10100110 10100110 … 10100110), then output D = R || R || … || R . Otherwise, output
1 2 m
INVALID.
7 Authenticated encryption mechanism 3 (CCM)
7.1 General
This clause defines an authenticated encryption mechanism commonly known as CCM (for counter
with CBC-MAC).
[10]
NOTE CCM is due to Whiting, Housley and Ferguson. The version of CCM defined here is a special case of
CCM as defined in References [8] and [10].
6 © ISO/IEC 2020 – All rights reserved

---------------------- Page: 11 ----------------------
ISO/IEC 19772:2020(E)

7.2 Specific notation
For the purposes of the specification of this mechanism, the following symbols and notation apply:
B block of bits used in computing the tag value
B , B , …, B sequence of blocks of bits (each of n bits) used in computing the tag value
1 2 v
C , C , …, C sequence of m 128-bit blocks obtained as part of the output of the authenticated en-
1 2 m
cryption process
D , D , …, D sequence of m 128-bit blocks obtained by partitioning a padded version of D
1 2 m
F flag octet
L length of D (in octets), excluding padding and the length block D
0
r the number of octets of D in the block D
m
S starting variable (of 120-8w bits)
T plaintext tag value (of t bits)
T′ recomputed tag value, generated during the decryption process
U encrypted tag value (of t bits)
v variable used in computing the tag value
w length of message length field in octets
X 128-bit block computed during the encryption and decryption processes
Y 128-bit block computed during the encryption and decryption processes
7.3 Specific requirements
In advance of any use of the mechanism, the originator and recipient of the data to which the
authenticated encryption mechanism is to be applied, shall agree on:
a) t, the bit-length of the tag; t shall be chosen from the set {32, 48, 64, 80, 96, 112, 128}; and
b) w, the octet-length of the message length field; w shall be chosen from the set {2, 3, 4, 5, 6, 7, 8}.
NOTE The choice of w affects the maximum message length which can be protected. The maximum message
8w+3 8w
length is 2 bits, i.e. 2 octets.
The block cipher to be used with this mechanism shall be a 128-bit block cipher, i.e. it shall have n=128.
The data string D to be protected using this mechanism, and the additional authenticated data string
A, shall contain a whole number of octets, i.e. their lengths shall be a multiple of 8 bits [i.e. len(D) and
len(A) shall both be an integer multiple of 8].
7.4 Encryption procedure
The originator shall perform the following steps to protect a data string D. Let L = len(D)/8, i.e. L is the
number of octets in D.
a) A starting variable S containing 15-w octets (i.e. 120-8w bits) shall be selected.
...