Rubber and plastics inlet hoses and hose assemblies for washing-machines and dishwashers — Specification

ISO 6804:2016 specifies the requirements for three types of rubber or plastics inlet hoses and hose assemblies for washing-machines and dishwashers connected to the domestic water supply at a pressure not exceeding 1 MPa (10 bar). It is applicable to the following types of hose: - type 1: rubber hoses for unheated water supply (maximum temperature 70 °C); - type 2: rubber hoses for heated water supply (maximum temperature 90 °C); - type 3: plastics hoses for unheated water supply (maximum temperature 60 °C). There may be national requirements for hose fittings and hoses conveying drinking water which must be complied with.

Tuyaux et flexibles en caoutchouc et en plastique pour l'alimentation des machines à laver et lave-vaisselle — Spécifications

General Information

Status
Withdrawn
Publication Date
31-Oct-2016
Current Stage
9599 - Withdrawal of International Standard
Completion Date
25-May-2023
Ref Project

Relations

Buy Standard

Standard
ISO 6804:2016 - Rubber and plastics inlet hoses and hose assemblies for washing-machines and dishwashers -- Specification
English language
13 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

INTERNATIONAL ISO
STANDARD 6804
Fourth edition
2016-11-01
Rubber and plastics inlet hoses
and hose assemblies for washing-
machines and dishwashers —
Specification
Tuyaux et flexibles en caoutchouc et en plastique pour l’alimentation
des machines à laver et lave-vaisselle — Spécifications
Reference number
ISO 6804:2016(E)
©
ISO 2016

---------------------- Page: 1 ----------------------
ISO 6804:2016(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2016, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2016 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 6804:2016(E)

Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Classification . 2
5 Couplings and fittings . 2
6 Materials and construction . 2
7 Dimensions and tolerances . 2
7.1 Inside diameters, tolerances and minimum wall thickness . 2
7.1.1 Type 1 and type 2 hoses . 2
7.1.2 Type 3 hoses . 3
7.2 Concentricity. 3
7.3 Tolerances on length . 3
8 Performance requirements for finished hoses and hose assemblies .3
8.1 Hydrostatic-pressure requirements (proof pressure test) . 3
8.2 Burst test . 3
8.3 Bending test . 3
8.4 Flexing tests . 4
8.4.1 General. 4
8.4.2 Sub-ambient temperature flexing test . 4
8.4.3 Standard laboratory temperature flexing test . 4
8.5 Resistance to kinking . 5
8.6 Resistance to hydrostatic pressure after ageing . 5
8.7 Resistance to ozone or weathering . 6
8.7.1 Resistance to ozone (type 1 and type 2 hoses) . 6
8.7.2 Resistance to weathering (type 3 hoses) . 6
8.8 Resistance to hydraulic-pressure impulse test . 6
8.9 Adhesion . 7
8.10 Mechanical resistance of thermoplastics coupling nuts . 7
9 Frequency of testing . 9
10 Test certificate . 9
11 Marking . 9
12 Recommendations for packaging and storage . 9
Annex A (normative) Type tests and routine tests .10
Annex B (informative) Recommended tests for production acceptance testing .11
Annex C (informative) Delivery certificate and test certificate.12
Bibliography .13
© ISO 2016 – All rights reserved iii

---------------------- Page: 3 ----------------------
ISO 6804:2016(E)

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the meaning of ISO specific terms and expressions related to conformity assessment,
as well as information about ISO’s adherence to the World Trade Organization (WTO) principles in the
Technical Barriers to Trade (TBT) see the following URL: www.iso.org/iso/foreword.html.
The committee responsible for this document is ISO/TC 45, Rubber and rubber products, Subcommittee
SC 1, Rubber and plastics hoses and hose assemblies.
This fourth edition cancels and replaces the third edition (ISO 6804:2009), which has been technically
revised with the following main changes:
— Clause 2 has been updated: ISO 1746 has been deleted and replaced by ISO 10619-1;
— Clause 8 has been extended to cover hydrostatic proof pressure tests and burst testing. A new table
(Table 2) has been added to specify maximum working pressures, proof pressures and minimum
burst pressures for each type. All subclauses have been renumbered;
— 8.5 (old 8.3) and 8.6 (old 8.4) have been extended with one line specifying the specific test pressures
for the different hose types after kinking and ageing tests;
— Clause 11 a), b), c), e) and example have been amended;
— Annex A and Annex B have been amended to include hydrostatic pressure proof test and burst
testing. The term “hose assembly” has been added to the description of routine tests. Table B.1
(column production acceptance test) has been filled in to specify which tests are recommended per
batch (the previous edition specified N.A. to all the tests);
— Table C.2 has been extended to show hydrostatic proof pressure test and burst test results.
iv © ISO 2016 – All rights reserved

---------------------- Page: 4 ----------------------
INTERNATIONAL STANDARD ISO 6804:2016(E)
Rubber and plastics inlet hoses and hose assemblies for
washing-machines and dishwashers — Specification
1 Scope
This document specifies the requirements for three types of rubber or plastics inlet hoses and hose
assemblies for washing-machines and dishwashers connected to the domestic water supply at a
pressure not exceeding 1 MPa (10 bar).
It is applicable to the following types of hose:
— type 1: rubber hoses for unheated water supply (maximum temperature 70 °C);
— type 2: rubber hoses for heated water supply (maximum temperature 90 °C);
— type 3: plastics hoses for unheated water supply (maximum temperature 60 °C).
There may be national requirements for hose fittings and hoses conveying drinking water which must
be complied with.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
ISO 188, Rubber, vulcanized or thermoplastic — Accelerated ageing and heat resistance tests
ISO 1307, Rubber and plastics hoses — Hose sizes, minimum and maximum inside diameters, and tolerances
on cut-to-length hoses
ISO 1402, Rubber and plastics hoses and hose assemblies — Hydrostatic testing
ISO 4671, Rubber and plastics hoses and hose assemblies — Methods of measurement of the dimensions of
hoses and the lengths of hose assemblies
ISO 4892 (all parts), Plastics — Methods of exposure to laboratory light sources
ISO 7326:2006, Rubber and plastics hoses — Assessment of ozone resistance under static conditions
ISO 8033, Rubber and plastics hoses — Determination of adhesion between components
ISO 8331, Rubber and plastics hoses and hose assemblies — Guidelines for selection, storage, use and
maintenance
ISO 10619-1:2011, Rubber and plastics hoses and tubing — Measurement of flexibility and stiffness —
Part 1: Bending tests at ambient temperature
ISO 23529, Rubber — General procedures for preparing and conditioning test pieces for physical test methods
3 Terms and definitions
For the purposes of this document, the terms and definitions given in ISO 8330 apply.
© ISO 2016 – All rights reserved 1

---------------------- Page: 5 ----------------------
ISO 6804:2016(E)

ISO and IEC maintain terminological databases for use in standardization at the following addresses:
— IEC Electropedia: available at http://www.electropedia.org/
— ISO Online browsing platform: available at http://www.iso.org/obp
4 Classification
Hoses are designated as one of the following three types, depending on the hose material and the
temperature of the water supply.
Type 1: Rubber hoses for a medium-temperature water supply (up to 70 °C) — for a maximum
working pressure of 1 MPa (10 bar).
Type 2: Rubber hoses for a high-temperature water supply (up to 90 °C) — for a maximum working
pressure of 1 MPa (10 bar).
Type 3: Plastics hoses for low temperature (up to 60 °C) water supply — for a maximum working
pressure of 0,8 MPa (8 bar).
5 Couplings and fittings
Hoses may be fitted with the appropriate type of coupling and end fitting to form hose assemblies.
NOTE Guidance on coupling types is given in ISO/TR 17784.
6 Materials and construction
The hose construction shall be as follows.
a) The hose lining shall consist of rubber for type 1 and type 2 or thermoplastics material for type 3.
b) The hose reinforcement shall consist of natural or synthetic textile material applied by any suitable
technique.
c) The hose cover shall consist of an ozone-resistant rubber for type 1 and type 2 or a weather-
resistant thermoplastics material for type 3 (or, alternatively, a stainless-steel braid may be used
instead of a cover).
The lining and the cover shall be of uniform thickness, concentric, fully gelled and free from visible
cracks, porosity, foreign inclusions and other defects which could cause the hose to be unserviceable.
7 Dimensions and tolerances
7.1 Inside diameters, tolerances and minimum wall thickness
7.1.1 Type 1 and type 2 hoses
The preferred values for the bore of the hose are 10 mm and 12,5 mm.
The tolerances on the bore will depend on the characteristics of the end fittings; consequently, they
shall be agreed between the manu
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.