Medical electrical equipment — Part 1-8: General requirements for basic safety and essential performance — Collateral standard: General requirements, tests and guidance for alarm systems in medical electrical equipment and medical electrical systems — Amendment 2

Appareils électromédicaux — Partie 1-8: Exigences générales pour la sécurité de base et les performances essentielles — Norme collatérale: Exigences générales, essais et guides pour les systèmes d'alarme des appareils et des systèmes électromédicaux — Amendement 2

General Information

Status
Published
Publication Date
22-Sep-2020
Current Stage
6060 - International Standard published
Start Date
31-Jul-2020
Due Date
07-Nov-2019
Completion Date
23-Sep-2020
Ref Project

Relations

Buy Standard

Standard
IEC 60601-1-8:2006/Amd 2:2020
English language
58 pages
sale 15% off
Preview
sale 15% off
Preview
Amendment with corrigendum
IEC_60601-1-8/2006
French language
56 pages
sale 15% off
Preview
sale 15% off
Preview
Draft
IEC 60601-1-8:2006/FDAmd 2
English language
54 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

IEC 60601-1-8

Edition 2.0 2020-07

INTERNATIONAL
STANDARD
colour
inside
AMENDMENT 2

Medical electrical equipment –
Part 1-8: General requirements for basic safety and essential performance –
Collateral standard: General requirements, tests and guidance for alarm
systems in medical electrical equipment and medical electrical systems


IEC 60601-1-8:2006-10/AMD2:2020-07(en)

---------------------- Page: 1 ----------------------
THIS PUBLICATION IS COPYRIGHT PROTECTED
Copyright © 2020 IEC, Geneva, Switzerland

All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form
or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from
either IEC or IEC's member National Committee in the country of the requester. If you have any questions about IEC
copyright or have an enquiry about obtaining additional rights to this publication, please contact the address below or
your local IEC member National Committee for further information.


IEC Central Office Tel.: +41 22 919 02 11
3, rue de Varembé info@iec.ch
CH-1211 Geneva 20 www.iec.ch
Switzerland

About the IEC
The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes
International Standards for all electrical, electronic and related technologies.

About IEC publications
The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the
latest edition, a corrigendum or an amendment might have been published.

IEC publications search - webstore.iec.ch/advsearchform Electropedia - www.electropedia.org
The advanced search enables to find IEC publications by a The world's leading online dictionary on electrotechnology,
variety of criteria (reference number, text, technical containing more than 22 000 terminological entries in English
committee,…). It also gives information on projects, replaced and French, with equivalent terms in 16 additional languages.
and withdrawn publications. Also known as the International Electrotechnical Vocabulary

(IEV) online.
IEC Just Published - webstore.iec.ch/justpublished

Stay up to date on all new IEC publications. Just Published IEC Glossary - std.iec.ch/glossary
details all new publications released. Available online and 67 000 electrotechnical terminology entries in English and
once a month by email. French extracted from the Terms and definitions clause of
IEC publications issued between 2002 and 2015. Some
IEC Customer Service Centre - webstore.iec.ch/csc entries have been collected from earlier publications of IEC
If you wish to give us your feedback on this publication or TC 37, 77, 86 and CISPR.

need further assistance, please contact the Customer Service

Centre: sales@iec.ch.

---------------------- Page: 2 ----------------------
IEC 60601-1-8



Edition 2.0 2020-07





INTERNATIONAL



STANDARD








colour

inside



AMENDMENT 2







Medical electrical equipment –

Part 1-8: General requirements for basic safety and essential performance –

Collateral standard: General requirements, tests and guidance for alarm

systems in medical electrical equipment and medical electrical systems
























INTERNATIONAL

ELECTROTECHNICAL


COMMISSION





ICS 11.040.01 ISBN 978-2-8322-8631-9





  Warning! Make sure that you obtained this publication from an authorized distributor.

---------------------- Page: 3 ----------------------
– 2 – IEC 60601-1-8:2006/AMD2:2020
© IEC 2020
FOREWORD
This amendment has been prepared by subcommittee 62A: Common aspects of electrical
equipment used in medical practice, of IEC technical committee 62: Electrical equipment in
medical practice, and ISO subcommittee 3: Respiratory devices and related equipment used for
patient care, of ISO technical committee 121: Anaesthetic and respiratory equipment.
It is published as a double logo amendment.
The text of this amendment is based on the following documents of IEC:
FDIS Report on voting
62A/1392/FDIS 62A/1407/RVD

Full information on the voting for the approval of this amendment can be found in the report on
voting indicated in the above table. In ISO, the amendment has been approved by 15 P
members out of 15 having cast a vote.
The committee has decided that the contents of this amendment and the base publication will
remain unchanged until the stability date indicated on the IEC web site under
"http://webstore.iec.ch" in the data related to the specific publication. At this date, the
publication will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.
NOTE The attention of users of this document is drawn to the fact that equipment manufacturers and testing
organizations may need a transitional period following publication of a new, amended or revised IEC or
ISO publication in which to make products in accordance with the new requirements and to equip themselves for
conducting new or revised tests. It is the recommendation of the committee that the content of this publication be
adopted for mandatory implementation nationally not earlier than 3 years from the date of publication.

IMPORTANT – The 'colour inside' logo on the cover page of this publication indicates
that it contains colours which are considered to be useful for the correct understanding
of its contents. Users should therefore print this document using a colour printer.

_____________

---------------------- Page: 4 ----------------------
IEC 60601-1-8:2006/AMD2:2020 – 3 –
© IEC 2020
INTRODUCTION TO AMENDMENT 2
The second edition of IEC 60601-1-8 was published in 2006 and amended in 2012. Since the
publication of IEC 60601-1-8:2006+A1:2012, the IEC Subcommittee (SC) 62A Secretariat has
been collecting issues from a variety of sources including comments from National Committees.
At the November 2015 meeting of IEC/SC 62A in Kobe, Japan, the subcommittee initiated a
process to identify high-priority issues that need to be considered in an amendment and should
not wait until the third edition of IEC 60601-1-8, which is presently targeted for publication
sometime after 2024.
Those issues selected for inclusion on the final "short list" to be addressed in Amendment 2
were those approved by a 2/3 majority of the National Committees present and voting at the
Frankfurt meeting of SC 62A. At the meeting held on 10 October 2016, 20 items were presented
to the National Committees present. All 20 items received the required 2/3 majority of the
National Committees present and voting and have been included in the "short list" for
consideration in preparing Amendment 2. All remaining issues have been placed on a "long list"
for consideration in the third edition of IEC 60601-1-8.
The "short list" of issues was documented in the design specification for Amendment 2. As
IEC 60601-1-8 was jointly developed with ISO/TC 121/SC 3, the work was assigned to
IEC/SC 62A-ISO/TC 121/SC 3 Joint Working Group (JWG) 2. JWG 2 was directed to consider
each issue described in Clause 6 of the design specification and develop an appropriate
solution for the identified problem. That final solution in this amendment can encompass any
technical solution proposed by the author of the issue or it can involve a different solution
developed by the expert group. The expert group can also have recommended that no change
to the standard was justified by the problem statement.
Because this is an amendment to IEC 60601-1-8:2006, the style in force at the time of
publication of IEC 60601-1-8 has been applied to this amendment. The style specified in
ISO/IEC Directives Part 2:2018 has only been applied when implementing the new style
guidance would not result in additional editorial changes. For example, notes to definitions are
designated as "NOTE" rather than "Note to entry" in Clause 3.
Users of this document should note that when constructing the dated references to specific
elements in a standard, such as definitions, amendments are only referenced if they modified
the text being cited. For example, if a reference is made to a definition that has not been
modified by an amendment, then the reference to the amendment is not included in the dated
reference.

---------------------- Page: 5 ----------------------
– 4 – IEC 60601-1-8:2006/AMD2:2020
© IEC 2020
INTRODUCTION
Replace, in the second sentence of the existing second paragraph, "source" with "origin".
1.3.1 IEC 60601-1
Replace the first two existing dashes with the following new dashes:
– "the general standard" designates IEC 60601-1 alone, including any amendments;
– "this collateral standard" designates IEC 60601-1-8 alone, including any amendments;
2 Normative references
Replace the existing references to IEC 60601-1, IEC 61672-1 and IEC 62366-1 by the following
new references:
IEC 60601-1:2005, Medical electrical equipment – Part 1: General requirements for basic safety
and essential performance
Amendment 1:2012
Amendment 2:2020
IEC 61672-1:2013, Electroacoustics – Sound level meters – Part 1: Specifications
IEC 62366-1:2015, Medical devices – Part 1: Application of usability engineering to medical
devices
Amendment 1:2020
3 Terms and definitions
Replace the existing first paragraph with the following new paragraph:
For the purposes of this document, the terms and definitions given in
IEC 60601-1:2005+A1:2012+A2:2020, IEC 62366-1:2015+A1:2020, and the following
definitions apply.
3.17
* DISTRIBUTED ALARM SYSTEM
Replace the existing term and definition with the following new entry:
3.17
* DISTRIBUTED ALARM SYSTEM
DAS
ALARM SYSTEM that involves more than one item of equipment in a ME SYSTEM intended for delivery
of ALARM CONDITIONS with technical confirmation
NOTE 1 The parts of a DISTRIBUTED ALARM SYSTEM can be widely separated in distance.
NOTE 2 A DISTRIBUTED ALARM SYSTEM is intended to notify OPERATORS of the existence of an ALARM CONDITION.
NOTE 3 For the purposes of this document, technical confirmation means that each element of a DISTRIBUTED ALARM
SYSTEM confirms or guarantees the successful delivery of the ALARM CONDITION to the next element or appropriate
TECHNICAL ALARM CONDITIONS are created as described in 6.11.2.2.1.
3.20
FALSE NEGATIVE ALARM CONDITION
Replace, in the existing note, "the equipment itself" with "the ALARM SYSTEM itself".

---------------------- Page: 6 ----------------------
IEC 60601-1-8:2006/AMD2:2020 – 5 –
© IEC 2020
3.22
HIGH PRIORITY
Replace the existing note with the following new notes:
NOTE 1 The priority is assigned through RISK ANALYSIS. See 6.1.2 for the assignment of priority.
NOTE 2 Immediate implies the interruption of current workflow is expected [59], [60].
3.23
*INFORMAL SIGNAL
Add, after the existing Example 3, the following new note:
NOTE An ADVISORY is a type of INFORMATION SIGNAL.
3.25
INTERBURST INTERVAL
Replace, in the existing parenthetical, "Figure 1" with "Figure 1 and Figure G.1".
Add the following new note:
NOTE For the purposes of this document, when an AUDITORY ICON is used, the INTERBURST INTERVAL begins at the
end of the AUDITORY ICON.
3.27
LOW PRIORITY
Replace the existing term, definition and note with the following new entry:
3.27
LOW PRIORITY
indicating that OPERATOR awareness is required and future action might be needed
NOTE 1 The priority is assigned through RISK ANALYSIS. See 6.1.2 for the assignment of priority.
NOTE 2 Awareness implies the planning of future workflow is expected [59], [60].
3.28
MEDIUM PRIORITY
Replace the existing note with the following new notes:
NOTE 1 The priority is assigned through RISK ANALYSIS. See 6.1.2 for the assignment of priority.
NOTE 2 Prompt implies the re-planning of current workflow is expected [59], [60].
3.37
* ACKNOWLEDGED
Replace the existing term, definition and notes, added by Amendment 1, with the following new
entry:
3.37
* ACKNOWLEDGED
state of an ALARM SYSTEM initiated by OPERATOR action, where the auditory ALARM SIGNAL
associated with a currently active ALARM CONDITION is inactivated until the ALARM CONDITION no
longer exists or until a predetermined time interval has elapsed
NOTE ACKNOWLEDGED only affects ALARM SIGNALS that are active at the time of the OPERATOR action.
Add, after 3.37, the following new terms and definitions:

---------------------- Page: 7 ----------------------
– 6 – IEC 60601-1-8:2006/AMD2:2020
© IEC 2020
3.38
* ADVISORY
ADVISORY SIGNAL
INFORMATION SIGNAL notifying the OPERATOR of a condition of the PATIENT or ME EQUIPMENT
providing contextual awareness that is intended to improve the clinical workflow or
PATIENT condition, the awareness not being intended as a means of RISK
understanding of the
CONTROL
NOTE 1 A notification that a lab result is available, where the lab result requires immediate clinical action is not an
ADVISORY. It is an ALARM CONDITION.
NOTE 2 A signal associated with an ADVISORY, which is an INFORMATION SIGNAL, is required by this document to be
designed so that an OPERATOR does not confuse it with an ALARM SIGNAL. See 6.3.2.2.2 and 6.3.3.2.
EXAMPLE 1 A notification that it is time to draw the next blood sample.
EXAMPLE 2 A battery status notification that replacement will be needed in a day.
EXAMPLE 3 A notification that it is time to bathe the PATIENT.
EXAMPLE 4 A notification that a lab result is available, where the lab results are normal.
3.39
ALARM FATIGUE
*
situation wherein the presence of frequent ALARM SIGNALS desensitizes an OPERATOR to an
ALARM SIGNAL
NOTE 1 A desensitized OPERATOR can fail to perceive, recognize or act on an ALARM SIGNAL.
NOTE 2 The response of a desensitized OPERATOR can be inadequate, delayed or non-existent.
NOTE 3 ALARM FLOOD can cause ALARM FATIGUE.
3.40
ALARM FLOOD
situation wherein OPERATORS receive more ALARM SIGNALS in a time period than they can
manage appropriately

NOTE See [56], [57].
3.41
* ALERT
synonym for the combination of PHYSIOLOGICAL ALARM CONDITIONS, TECHNICAL ALARM CONDITIONS
and ADVISORIES

[SOURCE: ISO/IEEE 11073-10201:2020 [76], 3.3, modified – Replaced "alarms" with "ALARM
CONDITIONS", "equipment-user advisory signals" with "ADVISORIES" and deleted "patient
related".]
3.42
AUDITORY ICON
sound that creates a strong semantic link to the category it represents
NOTE 1 An AUDITORY ICON is typically a real-world sound or mimics a real-world sound.
NOTE 2 An AUDITORY ICON can aid in locating the COMMUNICATOR and the SOURCE type.
3.43
AUDITORY POINTER
sound that attracts attention, denotes the priority and aids in localization of the COMMUNICATOR

---------------------- Page: 8 ----------------------
IEC 60601-1-8:2006/AMD2:2020 – 7 –
© IEC 2020
3.44
* CLINICALLY ACTIONABLE
type of ALARM CONDITION for which a panel of experts would agree that OPERATOR action is
necessary to prevent HARM within the timeframe implied by the priority communicated by the
ALARM SYSTEM
NOTE 1 An OPERATOR action can include assessment of a PATIENT or the changing of ALARM LIMITS when they are
inappropriately set for the state of the PATIENT.
NOTE 2 A LOW PRIORITY ALARM CONDITION, which requires action within the timeframe of a MEDIUM PRIORITY or HIGH
PRIORITY timeframe, is considered CLINICALLY ACTIONABLE. A HIGH PRIORITY ALARM CONDITION, which requires action
within the timeframe of a LOW PRIORITY or MEDIUM PRIORITY timeframe, is considered CLINICALLY NONACTIONABLE. In
both cases, the ALARM CONDITION priority was improperly assigned.
NOTE 3 A FALSE POSITIVE ALARM CONDITION is never considered CLINICALLY ACTIONABLE even though an unrelated
OPERATOR action might be required to prevent a future FALSE POSITIVE ALARM CONDITION.
NOTE 4 A CLINICALLY ACTIONABLE ALARM CONDITION is generally considered useful by the OPERATOR.
3.45
* CLINICALLY NONACTIONABLE
type of ALARM CONDITION for which a panel of experts would agree that OPERATOR action is not
expected within a timeframe equal to or shorter than the timeframe implied by its priority
NOTE 1 A LOW PRIORITY ALARM CONDITION, which requires action within the timeframe of a MEDIUM PRIORITY or HIGH
PRIORITY timeframe, is considered CLINICALLY ACTIONABLE. A HIGH PRIORITY ALARM CONDITION, which requires action
within the timeframe of a LOW PRIORITY or MEDIUM PRIORITY timeframe, is considered CLINICALLY NONACTIONABLE. In
both cases, the ALARM CONDITION priority was improperly assigned.
NOTE 2 CLINICALLY NONACTIONABLE ALARM CONDITIONS are considered detrimental to OPERATOR performance and
PATIENT safety.
NOTE 3 ALARM SIGNALS for an ALARM CONDITION of which the OPERATOR is already aware are considered CLINICALLY
NONACTIONABLE.
3.46
COMMUNICATOR
COM
ANNUNCIATOR
function of the ALARM SYSTEM that generates ALARM SIGNALS to notify an OPERATOR (e.g. to the
presence of an ALARM CONDITION)
NOTE 1 A COMMUNICATOR can receive an OPERATOR response.
NOTE 2 An OPERATOR response is not limited to direct OPERATOR action.
NOTE 3 See Figure 2.
3.47
DISTRIBUTED ALARM SYSTEM WITH OPERATOR CONFIRMATION
CDAS
DISTRIBUTED ALARM SYSTEM that includes the capability to receive an OPERATOR response
3.48
* DISTRIBUTED INFORMATION SYSTEM ABOUT ALARM CONDITIONS
DIS
system that involves more than one item of equipment in a ME SYSTEM intended to provide
information about ALARM CONDITIONS but does not guarantee delivery of that information
NOTE 1 A DISTRIBUTED INFORMATION SYSTEM ABOUT ALARM CONDITIONS is not intended to notify OPERATORS of the
existence of an ALARM CONDITION as a RISK CONTROL measure. A DISTRIBUTED INFORMATION SYSTEM ABOUT ALARM
CONDITIONS is intended to provide information about an ALARM CONDITION while the OPERATOR is aware of the
existence of the ALARM CONDITION by an ALARM SYSTEM.
NOTE 2 A DISTRIBUTED INFORMATION SYSTEM ABOUT ALARM CONDITIONS is not intended for confirmed delivery of
ALARM CONDITIONS.

---------------------- Page: 9 ----------------------
– 8 – IEC 60601-1-8:2006/AMD2:2020
© IEC 2020
3.49
INTEGRATOR
INT
ALARM MANAGER
function of the ALARM SYSTEM that distributes ALARM CONDITIONS, combines ALARM CONDITIONS
SOURCES or handles the communication between those SOURCES and COMMUNICATORS
from
NOTE 1 An INTEGRATOR can direct or redirect an ALARM CONDITION to another COMMUNICATOR and hence OPERATOR.
NOTE 2 An INTEGRATOR can send the acceptance of responsibility from a COMMUNICATOR to a SOURCE.
NOTE 3 See Figure 2.
3.50
* NUISANCE ALARM SIGNAL
ALARM SIGNAL for which a panel of experts would agree that the HARM associated with the ALARM
SIGNAL is greater than the benefit associated with action resulting from the ALARM SIGNAL
NOTE 1 A NUISANCE ALARM SIGNAL contributes to ALARM FATIGUE.
NOTE 2 A NUISANCE ALARM SIGNAL can arise from a FALSE POSITIVE ALARM CONDITION.
NOTE 3 A NUISANCE ALARM SIGNAL can arise from a CLINICALLY NONACTIONABLE ALARM CONDITION.
NOTE 4 A NUISANCE ALARM SIGNAL can cause an inappropriate OPERATOR action.
EXAMPLE Causing the OPERATOR to set ALARM LIMITS to inappropriate settings.
NOTE 5 An ALARM SIGNAL that unnecessarily irritates or startles the PATIENT or OPERATOR can be a NUISANCE ALARM
SIGNAL.
3.51
REDIRECTION
INTEGRATOR provides a response hierarchy for directing an ALARM CONDITION
means by which an
to a COMMUNICATOR or transfers an ALARM CONDITION to another COMMUNICATOR
NOTE See Figure 2.
3.52
RESPONSIBILITY ACCEPTED
state created by an OPERATOR response accepting ownership for addressing an ALARM
CONDITION
NOTE 1 A RESPONSIBILITY ACCEPTED can be used to initiate an ALARM SIGNAL inactivation state.
NOTE 2 See Figure 2.
3.53
RESPONSIBILITY REJECTED
state created by an OPERATOR response rejecting ownership for addressing an ALARM CONDITION
NOTE 1 A RESPONSIBILITY REJECTED can be used to initiate an ESCALATION or REDIRECTION.
NOTE 2 See Figure 2.
3.54
RESPONSIBILITY UNDEFINED
state, automatically initiated when neither a RESPONSIBILITY ACCEPTED nor RESPONSIBILITY
REJECTED is received within a specified period, which indicates that an OPERATOR is not
responding
NOTE 1 RESPONSIBILITY UNDEFINED is not used as an indication that the COMMUNICATOR and INTEGRATOR cannot
communicate.
NOTE 2 See Figure 2.

---------------------- Page: 10 ----------------------
IEC 60601-1-8:2006/AMD2:2020 – 9 –
© IEC 2020
3.55
SOURCE
SRC
function that has the capability to initiate an ALARM CONDITION
NOTE 1 The SOURCE transfers the ALARM CONDITION to the INTEGRATOR.
NOTE 2 See Figure 2.
3.56
TRUE NEGATIVE ALARM CONDITION
absence of an ALARM CONDITION when no valid triggering event has occurred in the PATIENT, the
equipment or the ALARM SYSTEM
3.57
TRUE POSITIVE ALARM CONDITION
presence of an ALARM CONDITION when a valid triggering event has occurred in the PATIENT, the
equipment or the ALARM SYSTEM
6.2 * Disclosures for INTELLIGENT ALARM SYSTEM
Replace the existing list item e) with the following new item:
e) changes the characteristics of the generated ALARM SIGNALS (for example, volume, pitch,
tempo, urgency, AUDITORY ICON category).
6.3.1 General
Replace, in the first sentence of the existing first paragraph, "ALARM SIGNALS" with "ALARM
SIGNALS by a COMMUNICATOR".
6.3.2.2.2 1 m (OPERATOR’s POSITION) visual ALARM SIGNALS and INFORMATION SIGNALS
Replace, in the existing Note 3, modified by Amendment 1, "IEC 62366" with "IEC 62366-1".
Replace the existing Note 5, added by Amendment 1, with the following new note:
NOTE 5 It is recognized that visual INFORMATION SIGNALS and visual ALARM SIGNALS can sometimes contain identical
or similar information. When they are intended to convey different meanings, care needs to be taken to ensure that
visual ALARM SIGNALS cannot be confused with visual INFORMATION SIGNALS.
6.3.3.1 * Characteristics of auditory ALARM SIGNALS
Replace, in the existing first paragraph, modified by Amendment 1, the first sentence with:
If a COMMUNICATOR of an ALARM SYSTEM is provided with auditory ALARM SIGNALS:
Replace the existing list item b) to d), modified by Amendment 1, with:
b) of HIGH PRIORITY, the HIGH PRIORITY auditory ALARM SIGNALS of that COMMUNICATOR shall
convey a higher level of urgency than the MEDIUM or LOW PRIORITY auditory ALARM SIGNALS of
that ALARM SIGNAL set as well as a higher level of urgency than any auditory INFORMATION
;
SIGNAL
c) of MEDIUM PRIORITY, the MEDIUM PRIORITY auditory ALARM SIGNALS of that COMMUNICATOR shall
convey a higher level of urgency than the LOW PRIORITY auditory ALARM SIGNALS of that ALARM
SIGNAL set as well as a higher level of urgency than any auditory INFORMATION SIGNAL;
d) the COMMUNICATOR shall have at least one set of ALARM SIGNALS that:
1) complies with Annex G; or

---------------------- Page: 11 ----------------------
– 10 – IEC 60601-1-8:2006/AMD2:2020
© IEC 2020
i) * A COMMUNICATOR with means to provide more than one set of auditory ALARM
SIGNALS should be equipped with at least one set of auditory ALARM SIGNALS that
complies with Annex G.
ALARM
2) * is generated by means of different technology (e.g. voice synthesizing of verbal
SIGNALS) and is VALIDATED (e.g. by clinical or simulated clinical USABILITY testing); or
3) * meets the requirements of Table 3 and Table 4.
Replace, in the existing Note 2, modified by Amendment 1, "IEC 62366" with "IEC 62366-1".
Delete the existing paragraph following Note 2.
Replace, in the third sentence of the existing compliance check, modified by Amendment 1,
"Verify" with "Confirm".
Delete t from the compliance check modified by Amendment 1.
r
Replace the existing last sentence of the compliance check, modified by Amendment 1, with
the following new sentence:
When the sound files of Annex G are utilized, only testing of t is required and testing of the
b
acoustic signal is permitted.
Replace the existing last paragraph, added by Amendment 1, with the following new paragraph:
Amongst the required frequency components with the largest sound pressure levels,
acoustically confirm the presence of at least one frequency component in range of 150 Hz to
1 000 Hz and at least the required components in the range of 150 Hz to 4 000 Hz in the auditory
ALARM SIGNAL at 1 m or the intended OPERATOR's POSITION. Only the AUDITORY POINTERS need
be tested when evaluating the ALARM SIGNALS of Annex G.
Table 3 – * Characteristics of the BURST of auditory ALARM SIGNALS
Replace, in the paragraph at the bottom of the table starting with "Where", modified by
Amendment 1, the third line with the following new text:
the variation of t , x and y within a BURST shall not exceed ± 20 %, and
d
Replace, in the existing table footnote c, "source" with "origin".

---------------------- Page: 12 ----------------------
IEC 60601-1-8:2006/AMD2:2020 – 11 –
© IEC 2020
Table 4 – * Characteristics of the PULSE of auditory ALARM SIGNALS
Replace the existing Table 4, modified by Amendment 1, with the following new table:
Characteristic Value
Frequency component in the range of 150 Hz to At least one that is among the four frequency
1 000 Hz components with the largest sound pressure level
Number of peaks in the frequency At least four peaks in the frequency domain
range of 150 Hz to 4 000Hz
Effective PULSE duration (t ) (see Figure 1)
d
75 ms to 200 ms
HIGH PRIORITY
125 ms to 250 ms
MEDIUM and LOW PRIORITY
a
RISE TIME (t ) (see Figure 1)

r
b
FALL TIME (t ) (see Figure 1)

f
Within the frequency range of 150 Hz to 4 000 Hz, the relative sound pressure levels of the four frequency
components with the largest sound pressure levels should be within 15 dB of each other.
NOTE Care is needed to ensure that the MEDIUM PRIORITY ALARM SIGNAL cannot be confused with the audible
emergency evacuation signal specified in ISO 8201:2017 [30].
a
The RISE TIME should not be so short as to create mechanical speaker noise.
b
The FALL TIME should be short enough to ensure that the PULSES do not overlap.

Figure 1 – Illustration of temporal characteristics of auditory ALARM SIGNALS
Replace, in the existing note, the word "NOTE" with "NOTE 1".
Add, after the existing note, the following new note:
NOTE 2 See Figure G.1 and Figure G.2 for additional information.
6.3.3.2 * Volume and characteristics of auditory ALARM SIGNALS and INFORMATION SIGNALS
Replace the existing first paragraph, modified by Amendment 1, with the following new
paragraph:
The auditory HIGH PRIORITY and MEDIUM PRIORITY ALARM SIGNAL sound pressure level range and
measurement radius, measured in accordance with the method of this subclause, shall be
ACCOMPANYING DOCUMENTS.
disclosed in the
Replace the existing list items c) to k), added by Amendment 1, with the following new items:
COMMUNICATOR on the floor and use a microphone of
c) Place the equipment containing the
the sound level meter complying with the requirements of type 1 instruments specified in
IEC 61672-1:2013, measure the sound pressure levels at least at positions 1, 2, 3, 4, 5, 6,
7, 8, 9 and 10, as specified in Figure B.1 and Table B.1 of ISO 3744:2010, in a hemisphere
with a radius of 1 m from the geometric centre of the COMMUNICATOR. For a large
COMMUNICATOR, where d , as calculated in Figure 1 a) of ISO 3744:2010, is greater than
O
0,5 m, utilize a radius such that the distance from the surface of the COMMUNICATOR to the
hemisphere is at least 0,5 m everywhere, extended to the next higher value in the series
1,5 m, 2 m, 2,5 m, 3 m, 3,5 m, 4 m.
d) Measure the maximum time-weighted sound pressure level using frequency weighting A and
the time weighting F of the sound level meter (i.e. L ).
AFmax
e) For ALARM SIGNALS utilizing AUDITORY POINTERS complying with Annex G, confirm that the
drive signal of the audio transducer utilizing an oscilloscope or other suitable instrument is
not clipped.

---------------------- Page: 13 ----------------------
– 12 – IEC 60601-1-8:2006/AMD2:2020
© IEC 2020
f) Calculate the A-weighted sound pressure level averaged over the measurement surface
according to 8.2.2 of ISO 3744:2010.
g) If the ALARM SYSTEM is provided with a MEDIUM PRIORITY ALARM CONDITION, simulate a MEDIUM
and repeat c) to f).
PRIORITY ALARM CONDITION
h) If the ALARM SYSTEM is provided with a LOW PRIORITY ALARM CONDITION, simulate a LOW
PRIORITY ALARM CONDITION and repeat c) to f).
i) Set the ALARM SIGNAL sound pressure level (volume level) to its minimum setting.
j) Repeat b) to h).
k) Confirm that the criteria for background noise, including any INFORMATION SIGNALS, specified
in 4.2 of ISO 3744:2010 are fulfilled.
l) Confirm that the measured sound pressure level range is in compliance with the values
ACCOMPANYING DOCUMENTS.
indicated in the
6.4.2 * Delays to or from a DISTRIBUTED ALARM SYSTEM
Replace the existing title and entire subclause 6.4.2, modified by Amendment 1, with the
following new text:
6.4.2 * Delays to or from a DISTRIBUTED INFORMATION SYSTEM ABOUT ALARM CONDITIONS (DIS)
or a DISTRIBUTED ALARM SYSTEM (DAS)
If an ALARM SYSTEM is provided with a means to send or receive ALARM CONDITIONS in a DIS or
DAS:
ALARM CONDITION to the point that the representation of
a) the delay time from the onset of the
the ALARM CONDITION leaves the SIGNAL INPUT/OUTPUT PART shall be disclosed in the
instructions for use; and
b) the maximum ALARM SIGNAL GENERATION DELAY of the COMMUNICATOR, including the method
ALARM SIGNAL GENERATION DELAY, or the time to determine
used to determine the maximum
the generation of the TECHNICAL ALARM CONDITION (see 6.11.2.2.1 b)) shall be disclosed in
the instructions for use.
The following methods may be used to determine the ALARM SIGNAL GENERATION DELAY
contribution fo
...

PROJET D’AMENDEMENT
IEC 60601-1-8:ISO custom-meta
generation-date/DAM 2
ISO/TC 121/SC 3 Secrétariat: ANSI
Début de vote: Vote clos le:
2019-05-24 2019-08-16
Appareils électromédicaux —
Partie 1-8:
Exigences générales pour la sécurité de base et les
performances essentielles — Norme collatérale: Exigences
générales, essais et guides pour les systèmes d'alarme des
appareils et des systèmes électromédicaux
AMENDEMENT 2
Medical electrical equipment —
Part 1-8: General requirements for basic safety and essential performance — Collateral standard:
General requirements, tests and guidance for alarm systems in medical electrical equipment and medical
electrical systems
AMENDMENT 2
ICS: 11.040.10
CE DOCUMENT EST UN PROJET DIFFUSÉ POUR
OBSERVATIONS ET APPROBATION. IL EST DONC
SUSCEPTIBLE DE MODIFICATION ET NE PEUT
ÊTRE CITÉ COMME NORME INTERNATIONALE
AVANT SA PUBLICATION EN TANT QUE TELLE.
Le présent document est distribué tel qu’il est parvenu du secrétariat du comité.
OUTRE LE FAIT D’ÊTRE EXAMINÉS POUR
ÉTABLIR S’ILS SONT ACCEPTABLES À DES
FINS INDUSTRIELLES, TECHNOLOGIQUES ET
COMMERCIALES, AINSI QUE DU POINT DE VUE
Ce projet est soumis à un vote parallèle à ISO et à IEC.
DES UTILISATEURS, LES PROJETS DE NORMES
INTERNATIONALES DOIVENT PARFOIS ÊTRE
CONSIDÉRÉS DU POINT DE VUE DE LEUR
POSSIBILITÉ DE DEVENIR DES NORMES
POUVANT SERVIR DE RÉFÉRENCE DANS LA
RÉGLEMENTATION NATIONALE.
Numéro de référence
LES DESTINATAIRES DU PRÉSENT PROJET
IEC 60601-1-8:2006/DAM 2:2019(F)
SONT INVITÉS À PRÉSENTER, AVEC LEURS
OBSERVATIONS, NOTIFICATION DES DROITS
DE PROPRIÉTÉ DONT ILS AURAIENT
ÉVENTUELLEMENT CONNAISSANCE ET À
©
FOURNIR UNE DOCUMENTATION EXPLICATIVE. IEC 2019

---------------------- Page: 1 ----------------------
62A/1325/CDV – 2 – IEC CDV 60601-1-8:2006/AMD2 © IEC:2019
1 AVANT-PROPOS
2 Le présent amendement a été établi par le sous-comité 62A: Aspects généraux des
3 équipements électriques utilisés en pratique médicale, du comité d’études 62 de l’IEC:
4 Équipements électriques dans la pratique médicale, et le sous-comité 3: Ventilateurs
5 pulmonaires et équipements connexes du comité technique 121 de l'ISO: Matériel d'anesthésie
6 et de réanimation respiratoire.
7 Le texte de cet amendement est issu des documents suivants:
FDIS Rapport de vote
62A/XXXX/FDIS 62A/XXXX/RVD
8
9 Le rapport de vote indiqué dans le tableau ci-dessus donne toute information sur le vote ayant
10 abouti à l'approbation de cet amendement.
11 Le comité a décidé que le contenu de cet amendement et de la publication de base ne sera pas
12 modifié avant la date de stabilité indiquée sur le site web de l'IEC sous
13 « http://webstore.iec.ch » dans les données relatives à la publication recherchée. À cette date,
14 la publication sera
15 • reconduite,
16 • supprimée,
17 • remplacée par une édition révisée, ou
18 • amendée.
19 Pour la présente publication, les Comités nationaux sont priés de noter que la date de
20 stabilité est 2024.
21 CE TEXTE EST INCLUS A TITRE D'INFORMATION POUR LES COMITES NATIONAUX. IL SERA SUPPRIME AU
22 STADE PUBLICATION.
23
IMPORTANT – Le logo « colour inside » qui se trouve sur la page de couverture de
cette publication indique qu'elle contient des couleurs qui sont considérées comme
utiles à une bonne compréhension de son contenu. Les utilisateurs devraient, par
conséquent, imprimer ce document en utilisant une imprimante couleur.
24 _____________
25 Note encadrée 1: Étant donné l’ampleur des modifications apportées par cet amendement, il a
26 été demandé aux Comités nationaux d’indiquer s’ils soutiendraient la publication finale en tant
27 que nouvelle édition de l’IEC 60601-1-8 plutôt qu’en tant que deuxième amendement tel qu’il a
28 été initialement prévu. Parmi les Comités nationaux qui ont répondu, le Comité national
29 allemand est fermement opposé à l’idée d’une nouvelle édition tandis que ceux de la Finlande et
30 de l’Afrique du Sud ont estimé qu’une nouvelle édition serait acceptable. À mesure que le projet
31 se poursuit, il convient que les Comités nationaux prennent en compte la section 2.10.3 des
32 directives ISO/IEC:
33 « Au stade approbation (voir 2.7), le Secrétaire général doit décider, en concertation avec le
34 secrétariat du comité technique ou du sous-comité, et en gardant à l'esprit à la fois les
35 conséquences financières pour l'organisation et les intérêts des utilisateurs de la Norme
36 internationale, s'il convient de publier un amendement ou une nouvelle édition de la Norme
37 internationale incorporant l'amendement. (Voir aussi 2.10.4.) »
38 En règle générale, si un amendement fait plus de 10 pages ou 15 % de la publication de base,
39 selon la plus petite des deux valeurs, il est d’usage que le Bureau central de l’IEC publie une
40 nouvelle édition complète plutôt que l’amendement.
41

---------------------- Page: 2 ----------------------
IEC CDV 60601-1-8:2006/AMD2 © IEC:2019 – 3 – 62A/1325/CDV
42 INTRODUCTION À L’AMENDEMENT 2
43 La deuxième édition de l‘IEC 60601-1-8 a été publiée en 2006 et amendée en 2012. Depuis la
44 publication de l’IEC 60601-1-8:2006/AMD1:2012, le Secrétariat du sous-comité (SC) 62A a
45 recueilli les préoccupations de différentes sources, y compris les commentaires des Comités
46 nationaux. Lors de la réunion du SC 62A de l’IEC en novembre 2015 à Kobe, au Japon, le
47 sous-comité a lancé un processus visant à identifier les questions hautement prioritaires qu’il y
48 a lieu de prendre en considération dans l’Amendement 2 et qu’il convient de traiter avant la
49 troisième édition, dont la publication est prévue peu après 2024.
50 Comme cela est spécifié au point 2 de la Résolution 1 de Kobe (62A/1069/RM), pour qu’une
51 question soit incluse dans la « sélection réduite » finale et soit traitée dans l’Amendement 2, la
52 question doit avoir été approuvée à la majorité des deux tiers des Comités nationaux présents
53 et votant à la réunion du SC 62A à Francfort. 20 points ont été présentés aux Comités nationaux
54 présents à la réunion du 10 octobre 2016. Les 20 points ont tous recueilli la majorité exigée des
55 2/3 des Comités nationaux présents et votants et ont été inclus dans la « sélection réduite »
56 pour examen lors de l’élaboration de l’Amendement 2. Toutes les questions restantes ont été
57 inscrites sur une « liste plus large » pour examen lors de la troisième édition.
58 La « sélection réduite » de questions a fait l’objet de documentation dans la Spécification de
59 conception de l’Amendement 2 (62A/1170/INF). L’IEC 60601-1-8 ayant été développée
60 conjointement avec le SC 3 du TC 121 de l’ISO, les travaux ont été confiés au Groupe de travail
61 commun (JWG) 2 IEC/SC 62A-ISO/TC 121/SC 3. Le JWG 2 a été chargé d’examiner les
62 questions décrites à l’Article 6 des spécifications de conception et de proposer une solution
63 appropriée au problème identifié. La solution finale proposée dans cet amendement peut inclure
64 les solutions techniques proposées par l’auteur de la question soulevée ou une solution
65 différente élaborée par le groupe d’experts. Le groupe d’experts a également pu indiquer que
66 l’énoncé du problème ne justifiait aucune modification de la norme.
67 Étant donné qu’il s’agit d’un amendement à l’édition 2006 de l’IEC 60601-1-8, le style en vigueur
68 à la date de publication de l’IEC 60601-1-8 a été appliqué au présent amendement. Le style
69 spécifié dans les directives ISO/IEC Partie 2:2018 n’a été appliqué que lorsque l’application du
70 nouveau guide stylistique n’entraînait pas de modifications rédactionnelles supplémentaires. Par
71 exemple, les notes aux définitions dans l’Article 3 sont désignées par « NOTE » plutôt que par
72 « Note à l’article ».
73 Il convient que les utilisateurs du présent document notent qu’à l’insertion des références
74 datées à des éléments spécifiques (aux définitions, par exemple) dans une norme, les
75 amendements ne sont référencés que s’ils modifient le texte cité. Par exemple, si une référence
76 est faite à une définition qui n’a pas été modifiée par un amendement, la référence à
77 l’amendement n’est pas incluse dans la référence datée.

---------------------- Page: 3 ----------------------
62A/1325/CDV – 4 – IEC CDV 60601-1-8:2006/AMD2 © IEC:2019
78 AVANT-PROPOS
79 Remplacer « l’Annexe H des Directives ISO/CEI, Partie 2 » par « l’Article 7 des directives
80 ISO/IEC, Partie 2:2018 » dans l’alinéa existant commençant par « Les formes verbales utilisées
81 dans la présente norme… »
82 Remplacer l’alinéa existant commençant par « Les articles, les paragraphes et les
83 définitions… » par:
84 Lorsqu’un astérisque (*) est utilisé comme premier caractère devant un titre, ou au début d’un
85 titre d’alinéa ou de tableau, il indique l’existence d’un guide ou d’une justification à consulter à
86 l’Annexe A.
87 INTRODUCTION
88 Dans la deuxième phrase du deuxième alinéa existant, remplacer « source » par « origine ».
89 Insérer, après le dernier alinéa existant de l’INTRODUCTION, les nouveaux alinéas suivants:
90 L’Amendement 1 à la présente norme a résolu la question des essais d’impulsions et de salves.
91 En outre, il a traité des points qui ont été soulevés par l’IEC/62D/MT 22, Appareils
92 électromédicaux de diagnostic et de surveillance des patients, au cours de la mise en œuvre
93 des exigences pour les SYSTEMES D'ALARME dans les normes particulières relevant de son
94 domaine de compétence.
95 L’Amendement 2 à la présente norme vise à traiter des questions hautement prioritaires
96 identifiées par une majorité des 2/3 des Comités nationaux présents et votants à la réunion de
97 l’IEC/SC 62A d’octobre 2016 à Francfort, en Allemagne, comme nécessitant d’être examinées
98 dans un amendement. Il convient, pour ce faire, de ne pas attendre la publication de la
99 troisième édition, dont la publication est prévue peu après 2024.
100 1 Domaine d'application, objet et normes connexes
101 1.3 Normes connexes
102 1.3.1 IEC 60601-1
103 Remplacer les textes existants des deux premiers tirets par:
104 ‒ « la norme générale » désigne l’IEC 60601-1 seule y compris les éventuels amendements;
105 ‒ « la présente norme collatérale » désigne l’IEC 60601-1-8 seule y compris les éventuels
106 amendements;
107 2 Références normatives
108 Note encadrée 2: Dans le cadre du projet en cours, des amendements à l’IEC 60601-1 ainsi
109 qu’un amendement à l’IEC 62366-1 sont en cours d’élaboration. Les références indiquées
110 ci-dessous seront mises à jour dès lors que le document a atteint le stade FDIS.
111 Remplacer, dans le premier alinéa existant, la première phrase par:
112 Les documents suivants sont cités dans le texte de sorte qu’ils constituent, pour tout ou partie
113 de leur contenu, des exigences du présent document.
114 Insérer, après le premier alinéa existant, la NOTE 1 et la NOTE 2 comme suit:
115 NOTE 1 La manière dont ces documents de référence sont cités dans les exigences normatives détermine la mesure
116 (en intégralité ou en partie) dans laquelle ils s’appliquent.
117 NOTE 2 Les références informatives sont répertoriées dans la bibliographie.
118 Mettre à jour les références normatives suivantes:
119 IEC 60601-1:2005, Appareils électromédicaux – Partie 1: Exigences générales pour la sécurité
120 de base et les performances essentielles

---------------------- Page: 4 ----------------------
IEC CDV 60601-1-8:2006/AMD2 © IEC:2019 – 5 – 62A/1325/CDV
121 IEC 60601-1:2005/AMD1:2012

2)
122 IEC 60601-1:2005/AMD2:—
123 IEC 61672-1:2013, Électroacoustique – Sonomètres – Partie 1: Spécifications
124 IEC 62366-1:2015, Dispositifs médicaux – Application de l'ingénierie de l'aptitude à l'utilisation
125 aux dispositifs médicaux

3)
126 IEC 62366-1:2015/AMD1:—
127 Ajouter les notes de bas de page 2) et 3) comme suit.
2)
128 Il existe une édition consolidée 3.2 (—) incluant l’IEC 60601-1:2005, son Amendement 1 (2012) et son
129 Amendement 2 (—).
3)
130 Il existe une édition consolidée 1.1 (—) incluant l’IEC 62366-1:2015 et son Amendement 1 (—).
131 3 Termes et définitions
132 Remplacer le premier alinéa existant par:
133 Pour les besoins du présent document, les termes et définitions donnés dans
134 l’IEC 60601-1:2005, l’IEC 60601-1:2005/AMD1:2012, l’IEC 60601-1:2005/AMD2:— et
135 l’IEC 62366-1:2015, ainsi que les suivants s’appliquent.
136 L'ISO et l'IEC tiennent à jour des bases de données terminologiques destinées à être utilisées
137 en normalisation, consultables aux adresses suivantes:
138 – IEC Electropedia: disponible à l’adresse http://www.electropedia.org/
139 – ISO Online browsing platform: disponible à l’adresse http://www.iso.org/obp
140 Remplacer la NOTE 2 existante par:
141 NOTE 2 Une liste des termes définis utilisés dans la présente norme collatérale est donnée dans l’index.
142 Remplacer le terme et la définition 3.17 existants par:
143 3.17
144 * SYSTEME D’ALARME REPARTI
145 DAS
146 SYSTEME D’ALARME qui implique plus d'un élément d’équipement dans un SYSTEME EM destiné à
147 fournir des CONDITIONS D’ALARME accompagnées d’une confirmation technique
148 NOTE 1 Les parties d'un SYSTEME D’ALARME REPARTI peuvent être situées à très grande distance les unes des
149 autres.
150 NOTE 2 Un SYSTEME D’ALARME REPARTI est destiné à informer les OPERATEURS de l’existence d’une CONDITION
151 D’ALARME.
152 NOTE 3 Pour les besoins du présent document, la confirmation technique signifie que chaque élément d’un SYSTEME
153 D’ALARME REPARTI confirme ou garantit la transmission réussie de la CONDITION D’ALARME au prochain élément ou que
154 des CONDITIONS D’ALARME TECHNIQUES appropriées sont créées, comme cela est décrit en 6.11.2.2.1.
155 NOTE 4 L’abréviation « DAS » est dérivée du terme anglais développé correspondant « distributed alarm system ».
156 Remplacer « appareil » par « SYSTEME D’ALARME » dans la note existante de la définition 3.20.
157 Remplacer la note existante de la définition 3.22 par ce qui suit:
158 NOTE 1 La priorité est attribuée dans le cadre d'une ANALYSE DE RISQUE. Voir 6.1.2 pour plus d’informations sur
159 l’attribution des priorités.

160 NOTE 2 « Immédiat » indique que l’interruption du flux de travaux en cours est attendue. [60], [61]
161 Ajouter une note après l’EXEMPLE 3 existant de la définition 3.23.
162 NOTE Une alerte est un type de SIGNAL D’INFORMATION.
163 Dans la parenthèse existante de la définition 3.25, remplacer « Figure 1 » par « Figure 1 et
164 Figure G.1 ».
165 Ajouter à la définition 3.25 la note suivante:

---------------------- Page: 5 ----------------------
62A/1325/CDV – 6 – IEC CDV 60601-1-8:2006/AMD2 © IEC:2019
166 NOTE Pour les besoins de la présente norme, l’INTERVALLE ENTRE SALVES commence à la fin de l’ICONE SONORE
167 lorsque ce dernier est utilisé.
168 Remplacer le terme, la définition et la note existants de la définition 3.27 par:
169 3.27
170 FAIBLE PRIORITE
171 indique que la vigilance de l’OPERATEUR est exigée ou une action future peut être nécessaire
172 NOTE 1 La priorité est attribuée dans le cadre d'une ANALYSE DE RISQUE. Voir 6.1.2 pour plus d’informations sur
173 l’attribution des priorités.

174 NOTE 2 « Vigilance » indique que la planification du flux de travaux futur peut être prévue. [60], [61]
175 Remplacer la note existante de la définition 3.28 par ce qui suit:
176 NOTE 1 La priorité est attribuée dans le cadre d'une ANALYSE DE RISQUE. Voir 6.1.2 pour plus d’informations sur
177 l’attribution des priorités.

178 NOTE 2 « Rapide » indique que la reprogrammation du flux de travaux en cours est attendue. [60], [61]
179 Remplacer le terme, la définition et les notes existants de la définition 3.37 par:
180 3.37
181 * ACQUITTE
182 état d'un SYSTEME D’ALARME initié par une action de l'OPERATEUR dans lequel le SIGNAL D’ALARME
183 sonore associé à une CONDITION D’ALARME active a été désactivé; cet état perdure jusqu'à ce que
184 la CONDITION D’ALARME soit résolue ou jusqu’à ce qu’un intervalle de temps prédéterminé soit
185 écoulé
186 ACQUITTE n'affecte que les SIGNAUX D’ALARME qui sont actifs au moment de l'action réalisée par
NOTE L'état
187 l'OPERATEUR.
188 Ajouter les nouvelles définitions suivantes:
189 3.38
190 FATIGUE LIEE AUX ALARMES
191 situation dans laquelle de fréquents SIGNAUX D’ALARME provoquent une désensibilisation de
192 l’OPERATEUR à un SIGNAL D’ALARME
193 NOTE 1 Un OPERATEUR désensibilisé peut échouer de percevoir, de reconnaître ou d’agir sur un SIGNAL D’ALARME.
194 NOTE 2 La réponse d’un OPERATEUR désensibilisé peut être inadéquate, retardée ou inexistante.
195 NOTE 3 L’INONDATION D’ALARME peut causer une FATIGUE LIEE AUX ALARMES.
196 3.39
197 INONDATION D’ALARME
198 état dans lequel les OPERATEURS reçoivent plus de SIGNAUX D’ALARME pendant une période

199 donnée qu’ils ne peuvent gérer de manière appropriée [57], [58]
200 3.40
201 * ALERTE
202 SIGNAL D’ALERTE
203 SIGNAL d’INFORMATION informant l'OPERATEUR de l’état du PATIENT ou de l'APPAREIL EM fournissant
204 une vigilance contextuelle destinée à améliorer le flux de travaux cliniques ou la compréhension
205 de l’état du PATIENT, mais cette vigilance n'est pas destinée à servir de moyen de MAITRISE DU
206 RISQUE
207 EXEMPLE 1 Une notification indiquant qu’il est temps de prélever le prochain échantillon de sang.
208 EXEMPLE 2 Une notification d’état de batterie indiquant que le remplacement sera nécessaire dans une journée.
209 EXEMPLE 3 Une notification indiquant qu'il est temps de laver le PATIENT.
210 3.41
211 ICONE SONORE
212 son qui crée un lien sémantique fort avec la catégorie qu’il représente
213 NOTE 1 Un ICONE SONORE est généralement un son du monde réel ou une imitation d’un son du monde réel.
214 NOTE 2 Un ICONE SONOre peut aider à localiser le COMMUNICATEUR et le type de SOURCE.

---------------------- Page: 6 ----------------------
IEC CDV 60601-1-8:2006/AMD2 © IEC:2019 – 7 – 62A/1325/CDV
215 3.42
216 INDICATEUR SONORE
217 son qui attire l’attention, indique la priorité et facilite la localisation du COMMUNICATEUR
218 3.43
219 * CLINIQUEMENT REALISABLE
220 type de CONDITION D’ALARME pour lequel un groupe d’experts convient que l’action de
221 l'OPERATEUR est nécessaire pour empêcher que des DOMMAGES ne surviennent dans les délais
222 prévus par la priorité attribuée par le SYSTEME D’ALARME
223 NOTE 1 Une action de l’OPERATEUR peut consister à évaluer un PATIENT ou à modifier les LIMITES D’ALARME
224 lorsqu'elles sont définies de manière inappropriée pour l’état du PATIENT.
225 NOTE 2 Une CONDITION D’ALARME DE FAIBLE PRIORITE, qui exige une action dans les délais impartis d’une PRIORITE
226 MOYENNE ou d’une PRIORITE ELEVEE, est considérée comme étant CLINIQUEMENT REALISABLE. Une CONDITION D’ALARME
227 DE PRIORITE ELEVEE, qui exige une action dans les délais impartis d’une FAIBLE PRIORITE ou d’une PRIORITE MOYENNE,
228 est considérée comme étant cliniquement non réalisable. Dans les deux cas, la priorité de la CONDITION D’ALARME n’a
229 pas été correctement attribuée.
230 NOTE 3 Une FAUSSE CONDITION D’ALARME POSITIVE n'est jamais considérée comme étant CLINIQUEMENT REALISABLE,
231 même si une action indépendante de l’OPERATEUR peut être exigée pour éviter une future FAUSSE CONDITION D’ALARME
232 POSITIVE.
233 NOTE 4 Une CONDITION D’ALARME CLINIQUEMENT REALISABLE est généralement considérée comme utile pour
234 l’OPERATEUR.
235 3.44
236 * CLINIQUEMENT NON REALISABLE
237 type de CONDITION D’ALARME pour lequel un groupe d’experts convient que l’action de
238 l'OPERATEUR n’est pas attendue dans un délai inférieur ou égal au délai prévu par sa priorité
239 NOTE 1 Une CONDITION D’ALARME DE FAIBLE PRIORITE, qui exige une action dans les délais impartis d’une priorité
240 moyenne ou d’une priorité élevée, est considérée comme étant CLINIQUEMENT REALISABLE. Une CONDITION D’ALARME DE
241 PRIORITE ELEVEE, qui exige une action dans les délais impartis d’une FAIBLE PRIORITE ou d’une PRIORITE MOYENNE, est
242 considérée comme étant CLINIQUEMENT NON REALISABLE. Dans les deux cas, la priorité de la CONDITION D’ALARME n’a
243 pas été correctement attribuée.
244 NOTE 2 Les conditions d’alarme CLINIQUEMENT NON REALISABLES sont considérées comme étant préjudiciables aux
245 performances de l’OPERATEUR et à la sécurité du PATIENT.
246 NOTE 3 Les SIGNAUX D’ALARME d’une CONDITION D’ALARME dont l’OPERATEUR a déjà connaissance sont considérés
247 comme CLINIQUEMENT NON REALISABLES.
248 3.45
249 COMMUNICATEUR
250 COM
251 ANNONCIATEUR
252 fonction du SYSTEME D’ALARME qui génère des SIGNAUX D’ALARME pour avertir un OPERATEUR
253 NOTE 1 Un COMMUNICATEUR peut recevoir une réponse de l’OPERATEUR.
254 NOTE 2 La réponse de l’OPERATEUR n’est pas limitée à une action directe de l’OPERATEUR.
255 3.46
256 SYSTEME D’ALARME REPARTI AVEC CONFIRMATION DE L’OPERATEUR
257 CDAS
258 SYSTEME D’ALARME REPARTI équipé de la capacité de recevoir une réponse de l’OPERATEUR
259 NOTE 1 L’abréviation « CDAS » est dérivée du terme anglais développé correspondant « distributed alarm system
260 with operator confirmation ».
261 3.47
262 * SYSTEME D’INFORMATION REPARTI SUR LES CONDITIONS D’ALARME
263 DIS
264 système qui implique plus d’un élément d’équipement d’un SYSTEME EM destiné à fournir des
265 informations sur les CONDITIONS D’ALARME, mais ne garantit pas la transmission de ces
266 informations
267 NOTE 1 Un SYSTEME D’INFORMATION REPARTI SUR LES CONDITIONS D’ALARME n'est pas destiné à informer les
268 OPERATEURS de l'existence d'une CONDITION D’ALARME à titre de mesure de MAITRISE DU RISQUE. Un SYSTEME
269 D’INFORMATION REPARTI SUR LES CONDITIONS D’ALARME vise à fournir de l’information sur une CONDITION D’ALARME
270 pendant que l’OPERATEUR est informé de l’existence de cette CONDITION D’ALARME par un SYSTEME D’ALARME.
271 NOTE 2 Un SYSTEME D’INFORMATION REPARTI SUR LES CONDITIONS D’ALARME n'est pas destiné à permettre l’existence
272 confirmée des CONDITIONS D’ALARME.

---------------------- Page: 7 ----------------------
62A/1325/CDV – 8 – IEC CDV 60601-1-8:2006/AMD2 © IEC:2019
273 NOTE 3 L’abréviation « DIS » est dérivée du terme anglais développé correspondant « distributed information
274 system about alarm conditions ».
275 3.48
276 INTEGRATEUR
277 INT
278 GESTIONNAIRE D’ALARME
279 fonction du SYSTEME D’ALARME qui gère la communication entre SOURCES et COMMUNICATEURS ou
280 avec d’autres INTEGRATEURS
281 NOTE 1 Un INTEGRATEUR peut diriger ou rediriger une CONDITION D’ALARME vers un autre COMMUNICATEUR et, par
282 conséquent, vers l’OPERATEUR.
283 NOTE 2 Un INTEGRATEUR peut transmettre l’acceptation de la responsabilité d’un COMMUNICATEUR à une SOURCE.
284 3.49
285 * SIGNAL D’ALARME NUISIBLE
286 SIGNAL D’ALARME pour lequel un groupe d’experts conviendrait que les DOMMAGES associés à ce
287 SIGNAL D’ALARME sont supérieurs aux avantages associés à une action résultant du SIGNAL
288 D’ALARME
289 NOTE 1 Un SIGNAL D’ALARME NUISIBLE contribue à la FATIGUE LIEE AUX ALARMES.
290 NOTE 2 Un SIGNAL D’ALARME NUISIBLE peut provenir d’une CONDITION D’ALARME CLINIQUEMENT NON REALISABLE.
291 NOTE 3 Un SIGNAL D’ALARME NUISIBLE peut provoquer une action inappropriée de l’OPERATEUR.
292 EXEMPLE L'OPERATEUR est amené à définir des LIMITES D’ALARME pour des réglages inappropriés.
293 NOTE 4 Un SIGNAL D’ALARME qui irrite ou fait sursauter inutilement le PATIENT ou l’OPERATEUR peut être considéré
294 comme un SIGNAL D’ALARME NUISIBLE.
295 3.50
296 REDIRECTION
297 moyen par lequel un INTEGRATEUR fournit une hiérarchie de réponses pour diriger une CONDITION
298 D’ALARME vers un COMMUNICATEUR ou redirige une CONDITION D’ALARME vers un autre
299 COMMUNICATEUR
300 3.51
301 RESPONSABILITE ACCEPTEE
302 état créé par une réponse de l’OPERATEUR acceptant d’être propriétaire de l’adressage d’une
303 CONDITION D’ALARME
304 NOTE Une RESPONSABILITE ACCEPTEE peut être utilisée pour initier un état de désactivation du SIGNAL D’ALARME.
305 3.52
306 RESPONSABILITE REJETEE
307 état créé par une réponse de l’OPERATEUR rejetant d’être propriétaire de l’adressage d’une
308 CONDITION D’ALARME
309 NOTE Une RESPONSABILITE REJETEE peut être utilisée pour initier une AUGMENTATION DU NIVEAU DE PRIORITE ou une
310 REDIRECTION.
311 3.53
312 RESPONSABILITE NON DEFINIE
313 état initié automatiquement lorsque ni une RESPONSABILITE ACCEPTEE ni une RESPONSABILITE
314 REJETEE ne sont reçues dans un délai spécifié, ce qui indique qu’un OPERATEUR ne répond pas
315 NOTE L’état RESPONSABILITE NON DEFINIE n’est pas utilisé pour indiquer que le COMMUNICATEUR et l’INTEGRATEUR ne
316 peuvent pas communiquer.
317 3.54
318 SOURCE
319 SRC
320 fonction qui a la capacité d’initier une CONDITION D'ALARME
321 NOTE La SOURCE peut accepter une attribution de responsabilité.
322 3.55
323 VRAIE CONDITION D’ALARME NEGATIVE
324 absence de CONDITION D’ALARME lorsqu’aucun événement déclenchant valable n’est apparu
325 concernant le PATIENT, l’appareil ou le SYSTEME D’ALARME

---------------------- Page: 8 ----------------------
IEC CDV 60601-1-8:2006/AMD2 © IEC:2019 – 9 – 62A/1325/CDV
326 3.56
327 VRAIE CONDITION D’ALARME POSITIVE
328 présence d'une CONDITION D’ALARME lorsqu'un événement déclenchant valable est apparu
329 concernant le PATIENT, l'appareil ou le SYSTEME D’ALARME
330 6 SYSTEMES D’ALARME
331 6.2 * INDICATIONS POUR LES SYSTEMES D’ALARME INTELLIGENTS
332 Remplacer le point e) existant par:
333 e) change les caractéristiques des SIGNAUX D’ALARME générés (par exemple volume, tonie,
334 tempo, urgence, catégorie d’ICONE SONORE).
335 6.3 Génération des SIGNAUX D’ALARME
336 6.3.1 Généralités
337 Remplacer la première phrase du premier alinéa existant par la suivante: « Chaque CONDITION
338 D’ALARME doit provoquer la génération de SIGNAUX D’ALARME visuels par un COMMUNICATEUR
339 comme cela est spécifié dans la norme collatérale. »
340 6.3.2 * SIGNAUX D’ALARME VISUELS
341 6.3.2.2 * Caractéristiques des SIGNAUX D’ALARME visuels
342 6.3.2.2.2 SIGNAUX D’ALARME visuels à 1 m (POSITION de l’opérateur) et SIGNAUX
343 D’INFORMATION
344 Remplacer, dans la NOTE 3 existante, « la CEI 62366 » par « l’IEC 62366-1 ».
345 Remplacer la NOTE 5 existante par ce qui suit:
346 NOTE 5 Il est reconnu que les SIGNAUX D’INFORMATION VISUELS et les SIGNAUX D’ALARME visuels peuvent parfois
347 contenir des informations identiques ou similaires. Il y a lieu de veiller à ce que les SIGNAUX D’ALARME visuels ne
348 puissent pas être confondus avec les SIGNAUX D’INFORMATION VISUELS lorsqu’ils sont destinés à véhiculer des
349 significations différentes.
350 6.3.3 * SIGNAUX D’ALARME SONORES
351 6.3.3.1 * Caractéristiques des SIGNAUX D’ALARME sonores
352 Remplacer, dans le premier alinéa existant, la première phrase par:
353 Si un COMMUNICATEUR d’un SYSTEME D’ALARME intègre des SIGNAUX D’ALARME sonores:
354 Remplacer les points b) à d) existants par:
355 b) de PRIORITE ELEVEE, les SIGNAUX D’ALARME sonores de PRIORITE ELEVEE de ce
356 COMMUNICATEUR doivent donner un niveau d'urgence supérieur à celui des SIGNAUX D’ALARME
357 sonores de PRIORITE MOYENNE ou FAIBLE de ce jeu de SIGNAUX D’ALARME, ainsi qu'un niveau
358 d'urgence supérieur à celui de tout SIGNAL D’INFORMATION sonore;
359 c) de PRIORITE MOYENNE, les SIGNAUX D’ALARME sonores de PRIORITE MOYENNE de ce
360 COMMUNICATEUR doivent donner un niveau d'urgence supérieur à celui des SIGNAUX D’ALARME
361 sonores de FAIBLE PRIORITE de ce jeu de SIGNAUX D’ALARME, ainsi qu'un niveau d'urgence
362 supérieur à celui de tout SIGNAL D’INFORMATION sonore;
363 d) le COMMUNICATEUR doit posséder au moins un jeu de SIGNAUX D’ALARME:
364 1) conforme à l’Annexe G; ou
365 i) * Il convient qu’un COMMUNICATEUR ayant les moyens de fournir plus d’un jeu de
366 SIGNAUX D’ALARME sonores soit équipé d'au moins un jeu de sIGNAUX D’ALARME
367 sonores conforme à l'Annexe G.
368 2) * généré au moyen de différentes technologies (par exemple, synthétiseur de SIGNAUX
369 D’ALARME vocaux) et qui est VALIDE (par exemple, par des essais cliniques ou des essais
370 cliniques simulés d'APTITUDE A L’UTILISATION); ou
371 3) qui satisfait aux exigences des Tableaux 3 et 4.
372 Remplacer « la CEI 62366 » par « l’IEC 62366-1 » dans la NOTE 2 existante.
373 Supprimer l’alinéa existant qui suit la NOTE 2.

---------------------- Page: 9 ----------------------
62A/1325/CDV – 10 – IEC CDV 60601-1-8:2006/AMD2 © IEC:2019
374 Remplacer « Vérifier » par « Confirmer » dans la troisième phrase du premier alinéa existant de
375 la vérification de conformité.
376 Supprimer t de la vérification de conformité.
r
377 Remplacer la dernière phrase existante du premier alinéa de la vérification de conformité par:
378 Lorsque les fichiers sonores de l'Annexe G sont utilisés, seuls les essais de t sont exigés et les
b
379 essais du signal acoustique sont autorisés.
380 Remplacer le second alinéa existant de la vérification de conformité par:
381 Dans les fréquences exigées, les composantes présentant les niveaux de pression acoustique
382 les plus élevés, confirment de manière acoustique la présence d'au moins une composante de
383 fréquence dans la plage de 150 Hz à 1 000 Hz et d'au moins les composantes exigées dans la
384 plage de 150 Hz à 4 000 Hz dans le SIGNAL D’ALARME sonore à 1 m ou à la position prévue de
385 l’opérateur. Lors de l’évaluation des SIGNAUX D’ALARME de l’Annexe G, il y a lieu de ne soumettre
386 à l’essai que les INDICATEURS SONORES.
387 Tableau 3 – * Caractéristiques de la SALVE des SIGNAUX D’ALARME SONORES
388 Dans la cinquième ligne existante du Tableau 3, remplacer la troisième ligne de texte suivant
389 « Où: » par:
390 la variation de t , x et y dans une SALVE ne doit pas dépasser ± 20 %, et
d
391 Remplacer, dans la note de bas de ta
...

FINAL
IEC
AMENDMENT
DRAFT
60601-1-8:2006
FDAM 2
ISO/TC 121/SC 3
Medical electrical equipment —
Secretariat: ANSI
Voting begins on:
Part 1-8:
2020-04-24
General requirements for basic safety
Voting terminates on:
and essential performance — Collateral
2020-06-19
standard: General requirements,
tests and guidance for alarm systems
in medical electrical equipment and
medical electrical systems
AMENDMENT 2
Appareils électromédicaux —
Partie 1-8: Exigences générales pour la sécurité de base et les
performances essentielles — Norme collatérale: Exigences générales,
essais et guides pour les systèmes d'alarme des appareils et des
systèmes électromédicaux
AMENDEMENT 2
This draft is submitted to a parallel vote in ISO and in IEC.
RECIPIENTS OF THIS DRAFT ARE INVITED TO
SUBMIT, WITH THEIR COMMENTS, NOTIFICATION
OF ANY RELEVANT PATENT RIGHTS OF WHICH
THEY ARE AWARE AND TO PROVIDE SUPPOR TING
DOCUMENTATION.
IN ADDITION TO THEIR EVALUATION AS
Reference number
BEING ACCEPTABLE FOR INDUSTRIAL, TECHNO-
IEC 60601-1-8:2006/FDAM 2:2020(E)
LOGICAL, COMMERCIAL AND USER PURPOSES,
DRAFT INTERNATIONAL STANDARDS MAY ON
OCCASION HAVE TO BE CONSIDERED IN THE
LIGHT OF THEIR POTENTIAL TO BECOME STAN-
DARDS TO WHICH REFERENCE MAY BE MADE IN
©
NATIONAL REGULATIONS. IEC 2020

---------------------- Page: 1 ----------------------
– 2 – IEC FDIS 60601-1-8:2006/AMD2
© IEC 2020
FOREWORD
This amendment has been prepared by subcommittee 62A: Common aspects of electrical
equipment used in medical practice, of IEC technical committee 62: Electrical equipment in
medical practice, and ISO subcommittee 3: Respiratory devices and related equipment used for
patient care, of ISO technical committee 121: Anaesthetic and respiratory equipment.
It is published as a double logo amendment.
The text of this amendment is based on the following documents of IEC:
FDIS Report on voting
62A/XXX/FDIS 62A/XXX/RVD

Full information on the voting for the approval of this amendment can be found in the report on
voting indicated in the above table. In ISO, the amendment has been approved by XXX P
members out of YYY having cast a vote.
The committee has decided that the contents of this amendment and the base publication will
remain unchanged until the stability date indicated on the IEC web site under
"http://webstore.iec.ch" in the data related to the specific publication. At this date, the
publication will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.
NOTE The attention of users of this document is drawn to the fact that equipment manufacturers and testing
organizations may need a transitional period following publication of a new, amended or revised IEC or
ISO publication in which to make products in accordance with the new requirements and to equip themselves for
conducting new or revised tests. It is the recommendation of the committee that the content of this publication be
adopted for mandatory implementation nationally not earlier than 3 years from the date of publication.

IMPORTANT – The 'colour inside' logo on the cover page of this publication indicates
that it contains colours which are considered to be useful for the correct understanding
of its contents. Users should therefore print this document using a colour printer.

_____________

---------------------- Page: 2 ----------------------
IEC FDIS 60601-1-8:2006/AMD2 – 3 –
© IEC 2020
INTRODUCTION TO AMENDMENT 2
The second edition of IEC 60601-1-8 was published in 2006 and amended in 2012. Since the
publication of IEC 60601-1-8:2006+A1:2012, the IEC Subcommittee (SC) 62A Secretariat has
been collecting issues from a variety of sources including comments from National Committees.
At the November 2015 meeting of IEC/SC 62A in Kobe, Japan, the subcommittee initiated a
process to identify high-priority issues that need to be considered in an amendment and should
not wait until the third edition of IEC 60601-1-8, which is presently targeted for publication
sometime after 2024.
Those issues selected for inclusion on the final "short list" to be addressed in Amendment 2
were those approved by a 2/3 majority of the National Committees present and voting at the
Frankfurt meeting of SC 62A. At the meeting held on 10 October 2016, 20 items were presented
to the National Committees present. All 20 items received the required 2/3 majority of the
National Committees present and voting and have been included in the "short list" for
consideration in preparing Amendment 2. All remaining issues have been placed on a "long list"
for consideration in the third edition of IEC 60601-1-8.
The "short list" of issues was documented in the design specification for Amendment 2. As
IEC 60601-1-8 was jointly developed with ISO/TC 121/SC 3, the work was assigned to
IEC/SC 62A-ISO/TC 121/SC 3 Joint Working Group (JWG) 2. JWG 2 was directed to consider
each issue described in Clause 6 of the design specification and develop an appropriate
solution for the identified problem. That final solution in this amendment can encompass any
technical solution proposed by the author of the issue or it can involve a different solution
developed by the expert group. The expert group can also have recommended that no change
to the standard was justified by the problem statement.
Because this is an amendment to IEC 60601-1-8:2006, the style in force at the time of
publication of IEC 60601-1-8 has been applied to this amendment. The style specified in
ISO/IEC Directives Part 2:2018 has only been applied when implementing the new style
guidance would not result in additional editorial changes. For example, notes to definitions are
designated as "NOTE" rather than "Note to entry" in Clause 3.
Users of this document should note that when constructing the dated references to specific
elements in a standard, such as definitions, amendments are only referenced if they modified
the text being cited. For example, if a reference is made to a definition that has not been
modified by an amendment, then the reference to the amendment is not included in the dated
reference.

---------------------- Page: 3 ----------------------
– 4 – IEC FDIS 60601-1-8:2006/AMD2
© IEC 2020
INTRODUCTION
Replace, in the second sentence of the existing second paragraph, "source" with "origin".
1.3.1 IEC 60601-1
Replace the first two existing dashes with the following new dashes:
– "the general standard" designates IEC 60601-1 alone, including any amendments;
– "this collateral standard" designates IEC 60601-1-8 alone, including any amendments;
2 Normative references
Replace the existing references to IEC 60601-1, IEC 61672-1 and IEC 62366-1 by the following
new references:
IEC 60601-1:2005, Medical electrical equipment – Part 1: General requirements for basic safety
and essential performance
Amendment 1:2012
Amendment 2:2020
IEC 61672-1:2013, Electroacoustics – Sound level meters – Part 1: Specifications
IEC 62366-1:2015, Medical devices – Part 1: Application of usability engineering to medical
devices
Amendment 1:2020
3 Terms and definitions
Replace the existing first paragraph with the following new paragraph:
For the purposes of this document, the terms and definitions given in
IEC 60601-1:2005+A1:2012+A2:2020, IEC 62366-1:2015+A1:2020, and the following
definitions apply.
3.17
* DISTRIBUTED ALARM SYSTEM
Replace the existing term and definition with the following new entry:
3.17
* DISTRIBUTED ALARM SYSTEM
DAS
ALARM SYSTEM that involves more than one item of equipment in a ME SYSTEM intended for delivery
of ALARM CONDITIONS with technical confirmation
NOTE 1 The parts of a DISTRIBUTED ALARM SYSTEM can be widely separated in distance.
NOTE 2 A DISTRIBUTED ALARM SYSTEM is intended to notify OPERATORS of the existence of an ALARM CONDITION.
NOTE 3 For the purposes of this document, technical confirmation means that each element of a DISTRIBUTED ALARM
SYSTEM confirms or guarantees the successful delivery of the ALARM CONDITION to the next element or appropriate
TECHNICAL ALARM CONDITIONS are created as described in 6.11.2.2.1.
3.20
FALSE NEGATIVE ALARM CONDITION
Replace, in the existing note, "the equipment itself" with "the ALARM SYSTEM itself".

---------------------- Page: 4 ----------------------
IEC FDIS 60601-1-8:2006/AMD2 – 5 –
© IEC 2020
3.22
HIGH PRIORITY
Replace the existing note with the following new notes:
NOTE 1 The priority is assigned through RISK ANALYSIS. See 6.1.2 for the assignment of priority.
NOTE 2 Immediate implies the interruption of current workflow is expected [59], [60].
3.23
*INFORMAL SIGNAL
Add, after the existing Example 3, the following new note:
NOTE An ADVISORY is a type of INFORMATION SIGNAL.
3.25
INTERBURST INTERVAL
Replace, in the existing parenthetical, "Figure 1" with "Figure 1 and Figure G.1".
Add the following new note:
NOTE For the purposes of this document, when an AUDITORY ICON is used, the INTERBURST INTERVAL begins at the
end of the AUDITORY ICON.
3.27
LOW PRIORITY
Replace the existing term, definition and note with the following new entry:
3.27
LOW PRIORITY
indicating that OPERATOR awareness is required and future action might be needed
NOTE 1 The priority is assigned through RISK ANALYSIS. See 6.1.2 for the assignment of priority.
NOTE 2 Awareness implies the planning of future workflow is expected [59], [60].
3.28
MEDIUM PRIORITY
Replace the existing note with the following new notes:
NOTE 1 The priority is assigned through RISK ANALYSIS. See 6.1.2 for the assignment of priority.
NOTE 2 Prompt implies the re-planning of current workflow is expected [59], [60].
3.37
* ACKNOWLEDGED
Replace the existing term, definition and notes, added by Amendment 1, with the following new
entry:
3.37
* ACKNOWLEDGED
state of an ALARM SYSTEM initiated by OPERATOR action, where the auditory ALARM SIGNAL
associated with a currently active ALARM CONDITION is inactivated until the ALARM CONDITION no
longer exists or until a predetermined time interval has elapsed
NOTE ACKNOWLEDGED only affects ALARM SIGNALS that are active at the time of the OPERATOR action.
Add, after 3.37, the following new terms and definitions:

---------------------- Page: 5 ----------------------
– 6 – IEC FDIS 60601-1-8:2006/AMD2
© IEC 2020
3.38
* ADVISORY
ADVISORY SIGNAL
INFORMATION SIGNAL notifying the OPERATOR of a condition of the PATIENT or ME EQUIPMENT
providing contextual awareness that is intended to improve the clinical workflow or
PATIENT condition, the awareness not being intended as a means of RISK
understanding of the
CONTROL
NOTE 1 A notification that lab result is available, where the lab result requires immediate clinical action is not an
ADVISORY. It is an ALARM CONDITION.
NOTE 2 A signal associated with an ADVISORY, which is an INFORMATION SIGNAL, is required by this document to be
designed so that an OPERATOR does not confuse it with an ALARM SIGNAL. See 6.3.2.2.2 and 6.3.3.2.
EXAMPLE 1 A notification that it is time to draw the next blood sample.
EXAMPLE 2 A battery status notification that replacement will be needed in a day.
EXAMPLE 3 A notification that it is time to bathe the PATIENT.
EXAMPLE 4 A notification that lab result is available, where the lab results are normal.
3.39
ALARM FATIGUE
*
situation wherein the presence of frequent ALARM SIGNALS desensitizes an OPERATOR to an
ALARM SIGNAL
NOTE 1 A desensitized OPERATOR can fail to perceive, recognize or act on an ALARM SIGNAL.
NOTE 2 The response of a desensitized OPERATOR can be inadequate, delayed or non-existent.
NOTE 3 ALARM FLOOD can cause ALARM FATIGUE.
3.40
ALARM FLOOD
situation wherein OPERATORS receive more ALARM SIGNALS in a time period than they can
manage appropriately

NOTE See [56], [57].
3.41
* ALERT
synonym for the combination of PHYSIOLOGICAL ALARM CONDITIONS, TECHNICAL ALARM CONDITIONS
and ADVISORIES

[SOURCE: ISO/IEEE 11073-10201:2020 [76], 3.3, modified – Replaced "alarms" with "ALARM
CONDITIONS", "equipment-user advisory signals" with "ADVISORIES" and deleted "patient
related".]
3.42
AUDITORY ICON
sound that creates a strong semantic link to the category it represents
NOTE 1 An AUDITORY ICON is typically a real-world sound or mimics a real-world sound.
NOTE 2 An AUDITORY ICON can aid in locating the COMMUNICATOR and the SOURCE type.
3.43
AUDITORY POINTER
sound that attracts attention, denotes the priority and aids in localization of the COMMUNICATOR

---------------------- Page: 6 ----------------------
IEC FDIS 60601-1-8:2006/AMD2 – 7 –
© IEC 2020
3.44
* CLINICALLY ACTIONABLE
type of ALARM CONDITION for which a panel of experts would agree that OPERATOR action is
necessary to prevent HARM within the timeframe implied by the priority communicated by the
ALARM SYSTEM
NOTE 1 An OPERATOR action can include assessment of a PATIENT or the changing of ALARM LIMITS when they are
inappropriately set for the state of the PATIENT.
NOTE 2 A LOW PRIORITY ALARM CONDITION, which requires action within the timeframe of a MEDIUM PRIORITY or HIGH
PRIORITY timeframe, is considered CLINICALLY ACTIONABLE. A HIGH PRIORITY ALARM CONDITION, which requires action
within the timeframe of a LOW PRIORITY or MEDIUM PRIORITY timeframe, is considered CLINICALLY NONACTIONABLE. In
both cases, the ALARM CONDITION priority was improperly assigned.
NOTE 3 A FALSE POSITIVE ALARM CONDITION is never considered CLINICALLY ACTIONABLE even though an unrelated
OPERATOR action might be required to prevent a future FALSE POSITIVE ALARM CONDITION.
NOTE 4 A CLINICALLY ACTIONABLE ALARM CONDITION is generally considered useful by the OPERATOR.
3.45
* CLINICALLY NONACTIONABLE
type of ALARM CONDITION for which a panel of experts would agree that OPERATOR action is not
expected within a timeframe equal to or shorter than the timeframe implied by its priority
NOTE 1 A LOW PRIORITY ALARM CONDITION, which requires action within the timeframe of a MEDIUM PRIORITY or HIGH
PRIORITY timeframe, is considered CLINICALLY ACTIONABLE. A HIGH PRIORITY ALARM CONDITION, which requires action
within the timeframe of a LOW PRIORITY or MEDIUM PRIORITY timeframe, is considered CLINICALLY NONACTIONABLE. In
both cases, the ALARM CONDITION priority was improperly assigned.
NOTE 2 CLINICALLY NONACTIONABLE ALARM CONDITIONS are considered detrimental to OPERATOR performance and
PATIENT safety.
NOTE 3 ALARM SIGNALS for an ALARM CONDITION of which the OPERATOR is already aware are considered CLINICALLY
NONACTIONABLE.
3.46
COMMUNICATOR
COM
ANNUNCIATOR
function of the ALARM SYSTEM that generates ALARM SIGNALS to notify an OPERATOR (e.g. the
presence of an ALARM CONDITION)
NOTE 1 A COMMUNICATOR can receive an OPERATOR response.
NOTE 2 An OPERATOR response is not limited to direct OPERATOR action.
NOTE 3 See Figure 2.
3.47
DISTRIBUTED ALARM SYSTEM WITH OPERATOR CONFIRMATION
CDAS
DISTRIBUTED ALARM SYSTEM that includes the capability to receive an OPERATOR response
3.48
* DISTRIBUTED INFORMATION SYSTEM ABOUT ALARM CONDITIONS
DIS
system that involves more than one item of equipment in a ME SYSTEM intended to provide
information about ALARM CONDITIONS but does not guarantee delivery of that information
NOTE 1 A disTRIBUTED INFORMATION SYSTEM ABOUT ALARM CONDITIONS is not intended to notify OPERATORS of the
existence of an ALARM CONDITION as a RISK CONTROL measure. A DISTRIBUTED INFORMATION SYSTEM ABOUT ALARM
CONDITIONS is intended to provide information about an ALARM CONDITION while the OPERATOR is aware of the
existence of the ALARM CONDITION by an ALARM SYSTEM.
NOTE 2 A DISTRIBUTED INFORMATION SYSTEM ABOUT ALARM CONDITIONS is not intended for confirmed delivery of
ALARM CONDITIONS.

---------------------- Page: 7 ----------------------
– 8 – IEC FDIS 60601-1-8:2006/AMD2
© IEC 2020
3.49
INTEGRATOR
INT
ALARM MANAGER
function of the ALARM SYSTEM that distributes ALARM CONDITIONS, combines ALARM CONDITIONS
SOURCES or handles the communication between those SOURCES and COMMUNICATORS
from
NOTE 1 An INTEGRATOR can direct or redirect an ALARM CONDITION to another COMMUNICATOR and hence OPERATOR.
NOTE 2 An INTEGRATOR can send the acceptance of responsibility from a COMMUNICATOR to a SOURCE.
NOTE 3 See Figure 2.
3.50
* NUISANCE ALARM SIGNAL
ALARM SIGNAL for which a panel of experts would agree that the HARM associated with the ALARM
SIGNAL is greater than the benefit associated with action resulting from the ALARM SIGNAL
NOTE 1 A NUISANCE ALARM SIGNAL contributes to ALARM FATIGUE.
NOTE 2 A NUISANCE ALARM SIGNAL can arise from a FALSE POSITIVE ALARM CONDITION.
NOTE 3 A NUISANCE ALARM SIGNAL can arise from a CLINICALLY NONACTIONABLE ALARM CONDITION.
NOTE 4 A NUISANCE ALARM SIGNAL can cause an inappropriate OPERATOR action.
EXAMPLE Causing the OPERATOR to set ALARM LIMITS to inappropriate settings.
NOTE 5 An ALARM SIGNAL that unnecessarily irritates or startles the PATIENT or OPERATOR can be a NUISANCE ALARM
SIGNAL.
3.51
REDIRECTION
means by which an INTEGRATOR provides a response hierarchy for directing an ALARM CONDITION
to a COMMUNICATOR or transfers an ALARM CONDITION to another COMMUNICATOR
NOTE See Figure 2.
3.52
RESPONSIBILITY ACCEPTED
state created by an OPERATOR response accepting ownership for addressing an ALARM
CONDITION
NOTE 1 A RESPONSIBILITY ACCEPTED can be used to initiate an ALARM SIGNAL inactivation state.
NOTE 2 See Figure 2.
3.53
RESPONSIBILITY REJECTED
state created by an OPERATOR response rejecting ownership for addressing an ALARM CONDITION
NOTE 1 A RESPONSIBILITY REJECTED can be used to initiate an ESCALATION or REDIRECTION.
NOTE 2 See Figure 2.
3.54
RESPONSIBILITY UNDEFINED
state, automatically initiated when neither a RESPONSIBILITY ACCEPTED nor RESPONSIBILITY
REJECTED is received within a specified period, which indicates that an OPERATOR is not
responding
NOTE 1 RESPONSIBILITY UNDEFINED is not used as an indication that the COMMUNICATOR and INTEGRATOR cannot
communicate.
NOTE 2 See Figure 2.

---------------------- Page: 8 ----------------------
IEC FDIS 60601-1-8:2006/AMD2 – 9 –
© IEC 2020
3.55
SOURCE
SRC
function that has the capability to initiate an ALARM CONDITION
NOTE 1 The SOURCE transfers the ALARM CONDITION to the INTEGRATOR.
NOTE 2 See Figure 2.
3.56
TRUE NEGATIVE ALARM CONDITION
absence of an ALARM CONDITION when no valid triggering event has occurred in the PATIENT, the
equipment or the ALARM SYSTEM
3.57
TRUE POSITIVE ALARM CONDITION
presence of an ALARM CONDITION when a valid triggering event has occurred in the PATIENT, the
equipment or the ALARM SYSTEM
6.2 * Disclosures for INTELLIGENT ALARM SYSTEM
Replace the existing list item e) with the following new item:
e) changes the characteristics of the generated ALARM SIGNALS (for example, volume, pitch,
tempo, urgency, AUDITORY ICON category).
6.3.1 General
Replace, in the first sentence of the existing first paragraph, "ALARM SIGNALS" with "ALARM
SIGNALS by a COMMUNICATOR".
6.3.2.2.2 1 m (OPERATOR’s POSITION) visual ALARM SIGNALS and INFORMATION SIGNALS
Replace, in the existing Note 3, modified by Amendment 1, "IEC 62366" with "IEC 62366-1".
Replace the existing Note 5, added by Amendment 1, with the following new note:
NOTE 5 It is recognized that visual INFORMATION SIGNALS and visual ALARM SIGNALS can sometimes contain identical
or similar information. When they are intended to convey different meanings, care needs to be taken to ensure that
visual ALARM SIGNALS cannot be confused with visual INFORMATION SIGNALS.
6.3.3.1 * Characteristics of auditory ALARM SIGNALS
Replace, in the existing first paragraph, modified by Amendment 1, the first sentence with:
If a COMMUNICATOR of an ALARM SYSTEM is provided with auditory ALARM SIGNALS:
Replace the existing list item b) to d), modified by Amendment 1, with:
b) of HIGH PRIORITY, the HIGH PRIORITY auditory ALARM SIGNALS of that COMMUNICATOR shall
convey a higher level of urgency than the MEDIUM or LOW PRIORITY auditory ALARM SIGNALS of
that ALARM SIGNAL set as well as a higher level of urgency than any auditory INFORMATION
;
SIGNAL
c) of MEDIUM PRIORITY, the MEDIUM PRIORITY auditory ALARM SIGNALS of that COMMUNICATOR shall
convey a higher level of urgency than the LOW PRIORITY auditory ALARM SIGNALS of that ALARM
SIGNAL set as well as a higher level of urgency than any auditory INFORMATION SIGNAL;
d) the COMMUNICATOR shall have at least one set of ALARM SIGNALS that:
1) complies with Annex G; or

---------------------- Page: 9 ----------------------
– 10 – IEC FDIS 60601-1-8:2006/AMD2
© IEC 2020
i) * A COMMUNICATOR with means to provide more than one set of auditory ALARM
SIGNALS should be equipped with at least one set of auditory ALARM SIGNALS that
complies with Annex G.
ALARM
2) * is generated by means of different technology (e.g., voice synthesizing of verbal
SIGNALS) and is VALIDATED (e.g., by clinical or simulated clinical USABILITY testing); or
3) * meets the requirements of Table 3 and Table 4.
Replace, in the existing Note 2, modified by Amendment 1, "IEC 62366" with "IEC 62366-1".
Delete the existing paragraph following Note 2.
Replace, in the third sentence of the existing compliance check, modified by Amendment 1,
"Verify" with "Confirm".
Delete t from the compliance check modified by Amendment 1.
r
Replace the existing last sentence of the compliance check, modified by Amendment 1, with
the following new sentence:
When the sound files of Annex G are utilized, only testing of t is required and testing of the
b
acoustic signal is permitted.
Replace the existing last paragraph, added by Amendment 1, with the following new paragraph:
Amongst the required frequency components with the largest sound pressure levels,
acoustically confirm the presence of at least one frequency component in range of 150 Hz to
1 000 Hz and at least the required components in the range of 150 Hz to 4 000 Hz in the auditory
ALARM SIGNAL at 1 m or the intended OPERATOR's POSITION. Only the AUDITORY POINTERS need
be tested when evaluating the ALARM SIGNALS of Annex G.
Table 3 – * Characteristics of the BURST of auditory ALARM SIGNALS
Replace, in the paragraph at the bottom of the table starting with "Where", modified by
Amendment 1, the third line with the following new text:
the variation of t , x and y within a BURST shall not exceed ± 20 %, and
d
Replace, in the existing table footnote c, "source" with "origin".

---------------------- Page: 10 ----------------------
IEC FDIS 60601-1-8:2006/AMD2 – 11 –
© IEC 2020
Table 4 – * Characteristics of the PULSE of auditory ALARM SIGNALS
Replace the existing Table 4, modified by Amendment 1, with the following new table:
Characteristic Value
Frequency component in the range of 150 Hz to At least one that is among the four frequency
1 000 Hz components with the largest sound pressure level
Number of peaks in the frequency At least four peaks in the frequency domain
range of 150 Hz to 4 000 Hz
Effective PULSE duration (t ) (see Figure 1)
d
75 ms to 200 ms
HIGH PRIORITY
125 ms to 250 ms
MEDIUM and LOW PRIORITY
a
RISE TIME (t ) (see Figure 1)

r
b
FALL TIME (t ) (see Figure 1)

f
Within the frequency range of 150 Hz to 4 000 Hz, the relative sound pressure levels of the four frequency
components with the largest sound pressure levels should be within 15 dB of each other.
NOTE Care is needed to ensure that the MEDIUM PRIORITY ALARM SIGNAL cannot be confused with the audible
emergency evacuation signal specified in ISO 8201:2017 [30].
a
The RISE TIME should not be so short as to create mechanical speaker noise.
b
The FALL TIME should be short enough to ensure that the PULSES do not overlap.

Figure 1 – Illustration of temporal characteristics of auditory ALARM SIGNALS
Replace, in the existing note, the word "NOTE" with "NOTE 1".
Add, after the existing note, the following new note:
NOTE 2 See Figure G.1 and Figure G.2 for additional information.
6.3.3.2 * Volume and characteristics of auditory ALARM SIGNALS and INFORMATION SIGNALS
Replace the existing first paragraph, modified by Amendment 1, with the following new
paragraph:
The auditory HIGH PRIORITY and MEDIUM PRIORITY ALARM SIGNAL sound pressure level range and
measurement radius, measured in accordance with the method of this subclause, shall be
ACCOMPANYING DOCUMENTS.
disclosed in the
Replace the existing list items c) to k), added by Amendment 1, with the following new items:
COMMUNICATOR on the floor and use a microphone of
c) Place the equipment containing the
the sound level meter complying with the requirements of type 1 instruments specified in
IEC 61672-1:2013, measure the sound pressure levels at least at positions 1, 2, 3, 4, 5, 6,
7, 8, 9 and 10, as specified in Figure B.1 and Table B.1 of ISO 3744:2010, in a hemisphere
with a radius of 1 m from the geometric centre of the COMMUNICATOR. For a large
COMMUNICATOR, where d , as calculated in Figure 1 a) of ISO 3744:2010, is greater than
O
0,5 m, utilize a radius such that the distance from the surface of the COMMUNICATOR to the
hemisphere is at least 0,5 m everywhere, extended to the next higher value in the series
1,5 m, 2 m, 2,5 m, 3 m, 3,5 m, 4 m.
d) Measure the maximum time-weighted sound pressure level using frequency weighting A and
the time weighting F of the sound level meter (i.e. L ).
AFmax
e) For ALARM SIGNALS utilizing AUDITORY POINTERS complying with Annex G, confirm that the
drive signal of the audio transducer utilizing an oscilloscope or other suitable instrument is
not clipped.

---------------------- Page: 11 ----------------------
– 12 – IEC FDIS 60601-1-8:2006/AMD2
© IEC 2020
f) Calculate the A-weighted sound pressure level averaged over the measurement surface
according to 8.2.2 of ISO 3744:2010.
g) If the ALARM SYSTEM is provided with a MEDIUM PRIORITY ALARM CONDITION, simulate a MEDIUM
and repeat c) to f).
PRIORITY ALARM CONDITION
h) If the ALARM SYSTEM is provided with a LOW PRIORITY ALARM CONDITION, simulate a LOW
PRIORITY ALARM CONDITION and repeat c) to f).
i) Set the ALARM SIGNAL sound pressure level (volume level) to its minimum setting.
j) Repeat b) to h).
k) Confirm that the criteria for background noise, including any INFORMATION SIGNALS, specified
in 4.2 of ISO 3744:2010 are fulfilled.
l) Confirm that the measured sound pressure level range is in compliance with the values
ACCOMPANYING DOCUMENTS.
indicated in the
6.4.2 * Delays to or from a DISTRIBUTED ALARM SYSTEM
Replace the existing title and entire subclause 6.4.2, modified by Amendment 1, with the
following new text:
6.4.2 * Delays to or from a DISTRIBUTED INFORMATION SYSTEM ABOUT ALARM CONDITIONS (DIS)
or a DISTRIBUTED ALARM SYSTEM (DAS)
If an ALARM SYSTEM is provided with a means to send or receive ALARM CONDITIONS in a DIS or
DAS:
ALARM CONDITION to the point that the representation of
a) the delay time from the onset of the
the ALARM CONDITION leaves the SIGNAL INPUT/OUTPUT PART shall be disclosed in the
instructions for use; and
b) the maximum ALARM SIGNAL GENERATION DELAY of the COMMUNICATOR, including the method
ALARM SIGNAL GENERATION DELAY, or the time to determine
used to determine the maximum
the generation of the TECHNICAL ALARM CONDITION (see 6.11.2.2.1 b)) shall be disclosed in
the instructions for use.
The following methods may be used to determine the ALARM SIGNAL GENERATION DELAY
contribution for each component of a DIS or DAS, as applicable:
c) from:
1) the onset of the ALARM CONDITION;
2) the time of the ALARM SIGNAL generation at the SOURCE;
3) the point that the presentation of the ALARM CONDITION leaves the SIGNAL INPUT/OUTPUT
PART of the SOURCE or INTEGRATOR; or
4) the point that the presentation of the ALARM CONDITION arrives at the SIGNAL INPUT/OUTPUT
PART of the INTEGRATOR or COMMUNICATOR;
d) to:
1) the point that the presentation of the ALARM CONDITION leaves the SIGNAL INPUT/OUTPUT
PART of the SOURCE or INTEGRATOR;
2) the point that the presentation of the ALARM CONDITION arrives at the SIGNAL INPUT/OUTPUT
PART of the INTEGRATOR or COMMUNICATOR; or
3) the time of the ALARM SIGNAL generation at the COMMUNICATOR.
Compliance is checked by functional testing under maximum load conditions of NORMAL USE and
inspection of the instructions for use.
6.5.4.2 * Selection of DEFAULT ALARM PRESET
Add, after the existing list item g), the following note:

---------------------- Page: 12 ----------------------
IEC FDIS 60601-1-8:2006/AMD2 – 13 –
© IEC 2020
NOTE Care is needed to ensure that the OPERATOR is aware of which previously retained ALARM SETTINGS are
being restored when the OPERATOR selects the retained ALARM SETTINGS.
Delete, in the existing compliance check, the word "source".
6.5.5 * Interruptions of less than or equal to 30 s
Delete, in the existing compliance check, the word "source".
6.7 * ALARM SYSTEM security
Replace, in the existing first paragraph, modified by Amendment 1, ''6.10 and 6.11.2.2.1" with
"6.10, 6.11.2.2.1 and 6.12.3."
6.8.1 * General
Add, after the existing third paragraph, the following new paragraph and note:
During the ALARM OFF or ALARM PAUSED ALARM SIGNAL inactivation states, the ALARM SYSTEM may
discontinue the processing of signals used to generate the inactivated ALARM CONDITIONS.
NOTE 3 If the ALARM SYSTEM discontinues the processing of a signal used to generate an ALARM CONDITION, the
ALARM SYSTEM log cannot log that ALARM CONDITION.
Renumber the existing Note 3, modified by Amendment 1, as Note 4.
Table 5 – ALARM SIGNAL inactivation states
Replace the existing fifth and sixth rows of Table 5, modified by Amendment 1, with the
following:
7 or 13
Indefinite ALARM CONDITION no 5 or
or 6
ACKNOWLEDGED
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.