iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ISO

ISO 7510:2017

(Main)

Plastics piping systems — Glass-reinforced plastics (GRP) components — Determination of the amounts of constituents

Plastics piping systems — Glass-reinforced plastics (GRP) components — Determination of the amounts of constituents

ISO 7510:2017 specifies a method for the determination of constituent materials of a test sample cut from a glass-reinforced plastics (GRP) component intended for use in a piping system. It includes determination of resin, glass, aggregate and filler contents. It is also applicable to the determination of the type and arrangement of the reinforcements. If used to determine the amounts of constituent materials in layered constructions it may be necessary to separate the laminate layers by cutting or splitting and testing each separately.

Systèmes de canalisations en matières plastiques — Composants plastiques renforcés de verre (PRV) — Détermination des teneurs des constituants

Le présent document spécifie une méthode pour la détermination des matériaux constituants d’un échantillon d’essai prélevé sur un composant en plastique renforcé de verre (PRV) destiné à être utilisé dans un système de canalisations. Il inclut la détermination de la teneur en résine, en verre, en agrégats et en charges. Il est aussi applicable à la détermination du type et de la disposition des renforts. S’il sert à déterminer les quantités des matériaux constituants dans des constructions en couches, il peut être nécessaire de séparer les couches de stratifié par découpage ou fractionnement pour les soumettre à l’essai séparément.

General Information

Status
Published
Publication Date
27-Jun-2017
ICS
23.040.20 - Plastics pipes
23.040.45 - Plastics fittings
Technical Committee
ISO/TC 138/SC 6 - Reinforced plastics pipes and fittings for all applications
Drafting Committee
ISO/TC 138/SC 6/WG 1 - Methods of test
Current Stage
9093 - International Standard confirmed
Completion Date
12-Sep-2022
Ref Project

Relations

Revises
ISO 7510:1997 - Plastics piping systems — Glass-reinforced plastics (GRP) components — Determination of the amounts of constituents using the gravimetric method
Effective Date
02-Nov-2013

Buy Standard

ISO 7510:2017 - Plastics piping systems -- Glass-reinforced plastics (GRP) components -- Determination of the amounts of constituentsISO 7510:2017 - Plastics piping systems -- Glass-reinforced plastics (GRP) components -- Determination of the amounts of constituents
PreviousNext
Standard
ISO 7510:2017 - Plastics piping systems -- Glass-reinforced plastics (GRP) components -- Determination of the amounts of constituents
English language
5 pages
sale 15% off
Preview
sale 15% off
Preview
ISO 7510:2017 - Systèmes de canalisations en matières plastiques — Composants plastiques renforcés de verre (PRV) — Détermination des teneurs des constituants Released:6. 10. 2023ISO 7510:2017 - Systèmes de canalisations en matières plastiques — Composants plastiques renforcés de verre (PRV) — Détermination des teneurs des constituants Released:6. 10. 2023
PreviousNext
Standard
ISO 7510:2017 - Systèmes de canalisations en matières plastiques — Composants plastiques renforcés de verre (PRV) — Détermination des teneurs des constituants Released:6. 10. 2023
French language
6 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

INTERNATIONAL ISO
STANDARD 7510
Second edition
2017-06
Plastics piping systems — Glass-
reinforced plastics (GRP) components
— Determination of the amounts of
constituents
Systèmes de canalisations en matières plastiques — Composants
plastiques renforcés de verre (PRV) — Détermination des teneurs des
constituants
Reference number
ISO 7510:2017(E)
©
ISO 2017

---------------------- Page: 1 ----------------------
ISO 7510:2017(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2017, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2017 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 7510:2017(E)

Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Principle . 1
5 Apparatus . 2
6 Test piece . 2
6.1 Dimensions . 2
6.2 Number . 3
7 Procedure. 3
8 Calculation and expression of results . 4
9 Test report . 4
Bibliography . 5
© ISO 2017 – All rights reserved iii

---------------------- Page: 3 ----------------------
ISO 7510:2017(E)

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular
...

NORME ISO
INTERNATIONALE 7510
Deuxième édition
2017-06
Systèmes de canalisations en
matières plastiques — Composants
plastiques renforcés de verre (PRV)
— Détermination des teneurs des
constituants
Plastics piping systems — Glass-reinforced plastics (GRP) components
— Determination of the amounts of constituents
Numéro de référence
ISO 7510:2017(F)
© ISO 2017

---------------------- Page: 1 ----------------------
ISO 7510:2017(F)
DOCUMENT PROTÉGÉ PAR COPYRIGHT
© ISO 2017
Tous droits réservés. Sauf prescription différente ou nécessité dans le contexte de sa mise en œuvre, aucune partie de cette
publication ne peut être reproduite ni utilisée sous quelque forme que ce soit et par aucun procédé, électronique ou mécanique,
y compris la photocopie, ou la diffusion sur l’internet ou sur un intranet, sans autorisation écrite préalable. Une autorisation peut
être demandée à l’ISO à l’adresse ci-après ou au comité membre de l’ISO dans le pays du demandeur.
ISO copyright office
Case postale 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Genève
Tél.: +41 22 749 01 11
E-mail: copyright@iso.org
Web: www.iso.org
Publié en Suisse
ii
  © ISO 2017 – Tous droits réservés

---------------------- Page: 2 ----------------------
ISO 7510:2017(F)
Sommaire Page
Avant-propos .iv
1 Domaine d’application . 1
2 Références normatives .1
3 Termes et définitions . 1
4 Principe. 1
5 Appareillage . 2
6 Éprouvette . 2
6.1 Dimensions . 2
6.2 Nombre . 3
7 Mode opératoire . 3
8 Calcul et expression des résultats .4
9 Rapport d’essai . 4
Bibliographie . 6
iii
© ISO 2017 – Tous droits réservés

---------------------- Page: 3 ----------------------
ISO 7510:2017(F)
Avant-propos
L’ISO (Organisation internationale de normalisation) est une fédération mondiale d’organismes
nationaux de normalisation (comités membres de l’ISO). L’élaboration des Normes internationales est
en général confiée aux comités techniques de l’ISO. Chaque comité membre intéressé par une étude
a le droit de faire partie du comité technique créé à cet effet. Les organisations internationales,
gouvernementales et non gouvernementales, en liaison avec l’ISO participent également aux travaux.
L’ISO collabore étroitement avec la Commission électrotechnique internationale (IEC) en ce qui
concerne la normalisation électrotechnique.
Les procédures utilisées pour élaborer le présent document et celles destinées à sa mise à jour sont
décrites dans les Directives ISO/IEC,
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ISO
ISO 7432:2021(Main)
Glass-reinforced thermosetting plastics (GRP) pipes and fittings — Test methods to prove the design of locked socket-and-spigot joints, including double-socket joints, with elastomeric seals

This document specifies methods of test for joints with a locked socket and spigot, including double-socket joints, and with elastomeric seals, for buried and above-ground glass-reinforced thermosetting plastics (GRP) piping systems. It covers methods of testing for leaktightness and resistance to damage of the joint only, when subjected to specified combinations of angular movement, compression (deformation) perpendicular to the pipe axis and internal pressure. It assumes that the joint will be exposed to the effects of hydrostatic end thrust. The tests detailed in 9.2, 9.3, 9.4 and 9.6 are applicable to joints with a locked socket and spigot, including double-socket joints, and with elastomeric seals intended to be used in buried or above-ground applications. The bending tests detailed in 9.5 can be used to prove the design where joints are either intended to be used in buried applications or are intended to be used in particular above-ground situations, where the tests can be considered appropriate. With the exception of the procedure detailed in 9.5, these test procedures are applicable to joints for pipes and fittings of all nominal sizes. The tests detailed in 9.5 are applicable to joints for pipes and fittings up to and including DN 600. The tests are applicable for evaluating joints intended for applications conveying liquids at temperatures specified in the referring standards. The test procedures in this document are damaging to the test piece, which will not be suitable for reuse after these tests. The test procedure is intended for type testing purposes. This document is applicable only to the joint and specifies methods of testing to prove its design.

  • Standard
    15 pages
    English language
    sale 15% off
  • Draft
    15 pages
    English language
    sale 15% off
ISO
ISO 10952:2021(Main)
Glass-reinforced thermosetting plastics (GRP) pipes and fittings — Determination of the resistance to chemical attack for the inside of a section in a deflected condition

This document specifies a method for determining the chemical resistance properties of glass-reinforced thermosetting plastics (GRP) pipes and fittings in a deflected condition for nominal sizes DN 100 and larger. In conjunction with ISO 10928, this document provides a method for evaluating the effect of a chemical environment on the interior of a pipe or fitting after a specified period of time. Test conditions and requirements are specified in the referring International Standard. ISO 23856 references this document. NOTE It has been found that the effect of chemical environments can be accelerated by strain induced from deflection; hence, this type of effect is frequently referred to as strain corrosion.

  • Standard
    9 pages
    English language
    sale 15% off
  • Draft
    9 pages
    English language
    sale 15% off
ISO
ISO 8533:2019(Main)
Glass-reinforced thermosetting plastics (GRP) pipes and fittings — Test methods to prove the design of cemented or wrapped joints

This document specifies methods of test for cemented or wrapped joints for buried and above ground glass-reinforced thermosetting plastics (GRP) piping systems. This document is only applicable to the joint and covers methods of test to prove its design. It assumes that the joint either is or is not intended to be subject to the effects of hydrostatic end thrust. The tests detailed in 9.2, 9.4 to 9.6 inclusive are applicable to cemented or wrapped joints intended to be used in buried or above-ground applications. The bending tests detailed in 9.3 can be used to prove the design where joints are either intended to be used in buried applications or are intended to be used in particular above-ground situations where the tests may be considered appropriate. With the exception of procedure detailed in 9.3, these test procedures are applicable to joints for pipes and fittings of all nominal sizes. The tests detailed in 9.3 are applicable to joints for pipes and fittings up to and including DN 600. The tests are applicable for evaluating joints intended for applications conveying liquids at temperatures specified in the referring standards. The test procedures in this document are damaging to the test piece, which will not be suitable for reuse after these tests. The test procedure is applied for type testing purposes only. This document is applicable only to the joint and specifies methods of test to prove its design.

  • Standard
    15 pages
    English language
    sale 15% off
ISO
ISO 8483:2019(Main)
Glass-reinforced thermosetting plastics (GRP) pipes and fittings — Test methods to prove the design of bolted flange joints

This document specifies methods of test for bolted flange joints for buried and above-ground glass-reinforced thermosetting plastics (GRP) piping systems. This document is only applicable to the joint and covers methods of test to prove its design. It assumes that the joint either is or is not intended to be subject to the effects of hydrostatic end thrust. The tests detailed in 9.2, 9.4 to 9.6 inclusive are applicable to bolted flange joints intended to be used in buried or above-ground applications. The bending tests detailed in 9.3 can be used to prove the design where joints are either intended to be used in buried applications or are intended to be used in particular above-ground situations where the tests may be considered appropriate. With the exception of the procedure detailed in 9.3, these test procedures are applicable to joints for pipes and fittings of all nominal sizes. The tests detailed in 9.3 are applicable to joints for pipes and fittings up to and including DN 600. The tests are applicable for evaluating joints intended for applications conveying liquids at temperatures specified in the referring standards. The test procedures in this document are damaging to the test piece, which will not be suitable for reuse after these tests. The test procedure is intended for type testing purposes. This document is applicable only to the joint and specifies methods of test to prove its design.

  • Standard
    17 pages
    English language
    sale 15% off
ISO
ISO 16611:2017(Main)
Plastics piping systems for drainage and sewerage without pressure — Non-circular pipes and joints made of glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resins (UP) — Dimensions, requirements and tests

ISO 16611:2017 specifies the required properties of the piping system and its components made from glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) intended to be used for drainage or sewerage without pressure including culverts. It is the responsibility of the purchaser or specifier to make the appropriate selections taking into account their particular requirements and any relevant national regulations and installation practices or codes. ISO 16611:2017 is applicable to non-circular GRP-UP pipes, with flexible or rigid joints, primarily intended for use in buried installations but may also be used to reline existing non-circular pipe lines. NOTE 1 GRP-UP includes pipes with vinyl ester liners or made entirely from vinyl ester. NOTE 2 Piping systems conforming to ISO 16611:2017 can be used also for non-buried applications provided the influence of the environment, e.g. from UV-radiation, and the supports are considered in the design of the pipes, fittings and joints. ISO 16611:2017 is applicable to pipes, fittings and their joints of nominal sizes from DN 150 to DN 4000, which are intended to be used for the conveyance of surface water or sewage at temperatures up to 50 °C.

  • Standard
    25 pages
    English language
    sale 15% off
ISO
ISO 10928:2016(Main)
Plastics piping systems — Glass-reinforced thermosetting plastics (GRP) pipes and fittings — Methods for regression analysis and their use

ISO 10928:2016 specifies procedures suitable for the analysis of data which, when converted into logarithms of the values, have either a normal or a skewed distribution. It is intended for use with the test methods and referring standards for glass-reinforced thermosetting plastics (GRP) pipes or fittings for the analysis of properties as a function of time. However, it can be used for the analysis of other data. Depending upon the nature of the data, two methods are specified. The extrapolation using these techniques typically extends the trend from data gathered over a period of approximately 10 000 h to a prediction of the property at 50 years, which is the typical maximum extrapolation time. ISO 10928:2016 only addresses the analysis of data. The test procedures to collect the data, the number of samples required and the time period over which data are collected are covered by the referring standards and/or test methods. Clause 6 discusses how the data analysis methods are applied to product testing and design.

  • Standard
    47 pages
    English language
    sale 15% off
  • Standard
    47 pages
    English language
    sale 15% off
ISO
ISO 15306:2003/Amd 1:2012(Amendment)
Glass-reinforced thermosetting plastics (GRP) pipes — Determination of the resistance to cyclic internal pressure — Amendment 1
  • Standard
    1 page
    English language
    sale 15% off
ISO
ISO 18672-1:2009(Main)
Plastics piping systems for non-pressure drainage and sewerage — Polyester resin concrete (PRC) — Part 1: Pipes and fittings with flexible joints

ISO 18672-1:2009 specifies definitions, requirements and characteristics of pipes, fittings, joints, materials, test methods and marking for pipes and fittings made from polyester resin concrete (PRC), intended to be used within a drain or sewer system operating without pressure. It applies to products for use in buried installations to be installed by open-trench techniques or pipe jacking. It applies to pipes, fittings and their joints of nominal sizes from DN 150 to DN 3000 for circular cross-sections, from WN/HN 300/450 to WN/HN 1400/2100 for egg-shaped cross-sections and from DN 800 to DN 1800 for kite-shaped cross-sections.

  • Standard
    68 pages
    English language
    sale 15% off
ISO
ISO 15306:2003(Main)
Glass-reinforced thermosetting plastics (GRP) pipes — Determination of the resistance to cyclic internal pressure

ISO 15306:2003 specifies a method for determining the resistance of glass-reinforced thermosetting plastics (GRP) pipes to cyclic internal pressure. Whilst the standard refers to pipes, the procedure described can also be applied to fittings.

  • Standard
    5 pages
    English language
    sale 15% off
ISO
ISO 7511:1999(Main)
Plastics piping systems — Glass-reinforced thermosetting plastics (GRP) pipes and fittings — Test methods to prove the leaktightness of the wall under short-term internal pressure

This International Standard specifies two test methods, designated method A and method B, for checking the leaktightness of glass-reinforced thermosetting plastics (GRP) pipes and fittings under short-term internal pressure. Method A is a hydraulic test applicable to a pipe under uniaxial stress. Method B is a pneumatic test applicable to fittings. NOTE Test methods for the leaktightness of joints or for the resistance of the pipe to long-term hydrostatic pressure are covered by other standards.

  • Standard
    4 pages
    English language
    sale 15% off