Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks — Part 7: Lining with spirally-wound pipes

This document, in conjunction with ISO 11296-1, specifies requirements and test methods for pipes which are formed on site by spirally winding and jointing a pre-manufactured profiled plastics strip, or a profiled plastics strip and integral locking joiner strip, and used for the renovation of underground non-pressure drainage and sewerage networks. It applies to spirally-wound pipes of fixed or variable diameter made of profiled plastics strips, with or without steel stiffening elements, and installed by one of two methods. The first method employs a dedicated winding machine in front of the open end of an existing pipeline, e.g. in a manhole. The pipes thus formed are simultaneously inserted into the existing pipeline by the winding forces, and by certain techniques can also be expanded in diameter after or during insertion. The second method employs a dedicated winding machine which forms the pipe as it traverses the existing pipeline from one manhole to the next. It applies to profiled plastics strips of unplasticized poly(vinyl chloride) (PVC U) with integral locking mechanism, or of high density polyethylene (HDPE) with integrally welded joints.

Systèmes de canalisations en plastique pour la rénovation des réseaux de branchements et de collecteurs d'assainissement enterrés sans pression — Partie 7: Tubage par enroulement hélicoïdal

Le présent document, conjointement avec l'ISO 11296‑1, spécifie les exigences et les méthodes d'essai applicables aux tubages formés sur place par enroulement hélicoïdal et assemblage d'une bande profilée préfabriquée en plastique, ou d'une bande profilée en plastique et d'une bande d'assemblage à verrouillage intégral, et utilisés pour la rénovation de réseaux de branchements et de collecteurs d'assainissement enterrés sans pression. Il s'applique aux tubages par enroulement hélicoïdal, de diamètre fixe ou variable, réalisés à partir de bandes profilées en plastique, avec ou sans éléments raidisseurs en acier, et installés en utilisant une parmi deux méthodes. La première méthode fait intervenir une machine à enrouler spécifique devant l'extrémité ouverte d'une canalisation existante, par exemple, dans un regard. Les tubages ainsi formés sont insérés simultanément dans la canalisation existante par les forces d'enroulement et certaines techniques permettent d'en élargir le diamètre pendant ou après l'insertion. La seconde méthode fait intervenir une machine à enrouler spécifique qui forme le tubage à mesure de sa progression à travers la canalisation existante d'un regard au regard suivant. Il s'applique à des bandes profilées plastiques en PVC-U (polychlorure de vinyle non plastifié) munies d'un mécanisme de verrouillage intégral, ou en polyéthylène haute densité (HDPE) avec joints intégralement soudés.

General Information

Status
Published
Publication Date
10-Jan-2019
Current Stage
9020 - International Standard under periodical review
Start Date
15-Jan-2024
Completion Date
15-Jan-2024
Ref Project

Relations

Buy Standard

Standard
ISO 11296-7:2019 - Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks
English language
16 pages
sale 15% off
Preview
sale 15% off
Preview
Standard
ISO 11296-7:2019 - Systemes de canalisations en plastique pour la rénovation des réseaux de branchements et de collecteurs d'assainissement enterrés sans pression
French language
18 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

INTERNATIONAL ISO
STANDARD 11296-7
Second edition
2019-01
Plastics piping systems for renovation
of underground non-pressure
drainage and sewerage networks —
Part 7:
Lining with spirally-wound pipes
Systèmes de canalisations en plastique pour la rénovation des réseaux
de branchements et de collecteurs d'assainissement enterrés sans
pression —
Partie 7: Tubage par enroulement hélicoïdal
Reference number
ISO 11296-7:2019(E)
©
ISO 2019

---------------------- Page: 1 ----------------------
ISO 11296-7:2019(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2019
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2019 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 11296-7:2019(E)

Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 2
4 Symbols and abbreviated terms . 3
4.1 Symbols . 3
4.2 Abbreviated terms . 3
5 Pipes at the “M” stage . 3
5.1 Materials . 3
5.2 General characteristics . 4
5.3 Material characteristics . 4
5.4 Geometric characteristics . 5
5.5 Mechanical characteristics. 6
5.6 Physical characteristics . 6
5.7 Jointing . 6
5.8 Marking . 6
6 Fittings at the “M” stage .
...

NORME ISO
INTERNATIONALE 11296-7
Deuxième édition
2019-01
Systèmes de canalisations en plastique
pour la rénovation des réseaux de
branchements et de collecteurs
d'assainissement enterrés sans
pression —
Partie 7:
Tubage par enroulement hélicoïdal
Plastics piping systems for renovation of underground non-pressure
drainage and sewerage networks —
Part 7: Lining with spirally-wound pipes
Numéro de référence
ISO 11296-7:2019(F)
©
ISO 2019

---------------------- Page: 1 ----------------------
ISO 11296-7:2019(F)

DOCUMENT PROTÉGÉ PAR COPYRIGHT
© ISO 2019
Tous droits réservés. Sauf prescription différente ou nécessité dans le contexte de sa mise en œuvre, aucune partie de cette
publication ne peut être reproduite ni utilisée sous quelque forme que ce soit et par aucun procédé, électronique ou mécanique,
y compris la photocopie, ou la diffusion sur l’internet ou sur un intranet, sans autorisation écrite préalable. Une autorisation peut
être demandée à l’ISO à l’adresse ci-après ou au comité membre de l’ISO dans le pays du demandeur.
ISO copyright office
Case postale 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Genève
Tél.: +41 22 749 01 11
Fax: +41 22 749 09 47
E-mail: copyright@iso.org
Web: www.iso.org
Publié en Suisse
ii © ISO 2019 – Tous droits réservés

---------------------- Page: 2 ----------------------
ISO 11296-7:2019(F)

Sommaire Page
Avant-propos .iv
Introduction .v
1 Domaine d'application . 1
2 Références normatives . 1
3 Termes et définitions . 2
4 Symboles et abréviations . 3
4.1 Symboles . 3
4.2 Abréviations . 4
5 Tuyaux au stade «M» . 4
5.1 Matières . 4
5.2 Caractéristiques générales. 4
5.3 Caractéristiques de la matière . 5
5.4 Caractéristiques géométriques . 5
5.5 Caractéristiques mécaniques . 7
5.6 Caractéristiques physiques . 7
5.7 Assemblage . 7
5.8 Marquage . 7
6 Raccords au stade «M» .
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.