Electric Motor-Operated Hand-Held Tools, Transportable Tools and Lawn and Garden Machinery - Safety - Part 4-1: Particular requirements for chain saws (IEC 62841-4-1:2017)

EN-IEC 62841-4-1 applies to chain saws for cutting wood and designed for use by one person. This standard does not cover chain saws designed for use in conjunction with a guide-plate and riving knife or in any other way such as with a support or as a stationary or transportable machine. This standard does not apply to - chain saws for tree service as defined in ISO 11681-2; or - pole-mounted pruners. The chain saws covered by this standard are designed only to be operated with the right hand on the rear handle and the left hand on the front handle.

Elektrische motorbetriebene handgeführte Werkzeuge, transportable Werkzeuge und Rasen- und Gartenmaschinen – Sicherheit - Teil 4-1: Besondere Anforderungen für Kettensägen (IEC 62841-4-1:2017)

Outils électroportatifs à moteur, outils portables et machines pour jardins et pelouses - Sécurité - Partie 4-1: Exigences particulières pour les scies à chaîne (IEC 62841-4-1:2017)

IEC 62841-4-1:2017 s'applique aux scies à chaîne pour la découpe du bois et conçues pour être utilisées par une personne. La présente Norme ne couvre pas les scies à chaîne conçues pour être utilisées conjointement avec un guide-chaîne et une fendeuse, ni de toute autre manière (avec un support ou en tant que machine fixe ou portable, par exemple).
La présente Norme ne s'applique pas aux scies à chaîne pour l'élagage telles que définies dans l'ISO 11681-2; ou aux élagueurs sur perche.
Les élagueurs sur perche sont couverts par une partie ultérieure de l'IEC 62841.
Les scies à chaîne couvertes par la présente Norme sont conçues uniquement pour être utilisées main droite sur la poignée arrière et main gauche sur la poignée avant.
La présente Partie 4-1 doit être utilisée conjointement avec la première édition de l'IEC 62841-1 (2014).
L’attention des Comités Nationaux est attirée sur le fait que les fabricants d’appareils et les organismes d’essai peuvent avoir besoin d’une période transitoire après la publication d’une nouvelle publication IEC, ou d’une publication amendée ou révisée, pour fabriquer des produits conformes aux nouvelles exigences et pour adapter leurs équipements aux nouveaux essais ou aux essais révisés.
Le comité recommande que le contenu de cette publication soit entériné au niveau national au plus tôt 36 mois après la date de publication.
Mots clés: scies à chaîne, Outils électroportatifs, Sécurité

Elektromotorna ročna orodja, prenosna orodja ter stroji za trato in vrt - Varnost - 4-1. del: Posebne zahteve za verižne žage (IEC 62841-4-1:2017)

General Information

Status
Published
Publication Date
07-Apr-2020
Technical Committee
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
02-Apr-2020
Due Date
07-Jun-2020
Completion Date
08-Apr-2020

Relations

Buy Standard

Standard
EN 62841-4-1:2020 - BARVE
English language
68 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 62841-4-1:2020
01-junij-2020
Nadomešča:
SIST EN 60745-2-13:2009
SIST EN 60745-2-13:2009/A1:2011
Elektromotorna ročna orodja, prenosna orodja ter stroji za trato in vrt - Varnost - 4-
1. del: Posebne zahteve za verižne žage (IEC 62841-4-1:2017)
Electric Motor-Operated Hand-Held Tools, Transportable Tools and Lawn and Garden
Machinery - Safety - Part 4-1: Particular requirements for chain saws (IEC 62841-4-
1:2017)
Elektrische motorbetriebene handgeführte Werkzeuge, transportable Werkzeuge und
Rasen- und Gartenmaschinen – Sicherheit - Teil 4-1: Besondere Anforderungen für
Kettensägen (IEC 62841-4-1:2017)
Outils électroportatifs à moteur, outils portables et machines pour jardins et pelouses -
Sécurité - Partie 4-1: Exigences particulières pour les scies à chaîne (IEC 62841-4-
1:2017)
Ta slovenski standard je istoveten z: EN 62841-4-1:2020
ICS:
25.080.60 Strojne žage Sawing machines
25.140.20 Električna orodja Electric tools
65.060.80 Gozdarska oprema Forestry equipment
SIST EN 62841-4-1:2020 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN 62841-4-1:2020

---------------------- Page: 2 ----------------------
SIST EN 62841-4-1:2020

EUROPEAN STANDARD EN 62841-4-1

NORME EUROPÉENNE

EUROPÄISCHE NORM
March 2020
ICS 25.140.20 Supersedes EN 60745-2-13:2009 and all of its
amendments and corrigenda (if any)
English Version
Electric Motor-Operated Hand-Held Tools, Transportable Tools
and Lawn and Garden Machinery - Safety - Part 4-1: Particular
requirements for chain saws
(IEC 62841-4-1:2017 , modified)
Outils électroportatifs à moteur, outils portables et machines
Elektrische motorbetriebene handgeführte Werkzeuge,
pour jardins et pelouses - Sécurité - Partie 4-1: Exigences transportable Werkzeuge und Rasen- und
particulières pour les scies à chaîne Gartenmaschinen - Sicherheit - Teil 4-1: Besondere
(IEC 62841-4-1:2017 , modifiée) Anforderungen für Kettensägen
(IEC 62841-4-1:2017 , modifiziert)
This European Standard was approved by CENELEC on 2017-11-15. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.



European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2020 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
 Ref. No. EN 62841-4-1:2020 E

---------------------- Page: 3 ----------------------
SIST EN 62841-4-1:2020
EN 62841-4-1:2020 (E)

European foreword
The text of document 116/339/FDIS, future edition 1 of IEC 62841-4-1, prepared by IEC/TC 116 "Safety
of motor-operated electric tools" was submitted to the IEC-CENELEC parallel vote and approved by
CENELEC as EN 62841-4-1:2020.
A draft amendment, which covers common modifications to IEC 62841-4-1 (116/339/FDIS), was prepared
by CLC/TC 116 "Safety of motor-operated electric tools" and approved by CENELEC.
The following dates are fixed:
• latest date by which this document has (dop) 2020-09-13
to be implemented at national level by
publication of an identical national
standard or by endorsement
• latest date by which the national (dow) 2024-03-13
standards conflicting with this document
have to be withdrawn
EN 62841-4-1:2020 supersedes EN 60745-2-13:2009 + A1:2010.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.
This European Standard is divided into four parts:
Part 1: General requirements which are common to most hand-held electric motor operated tools
(for the purpose of this standard referred to simply as tools) which could come within the
scope of this standard;
Part 2, 3 or 4: Requirements for particular types of tools which either supplement or modify the
requirements given in Part 1 to account for the particular hazards and characteristics of
these specific tools.
This Part 4-1 is to be used in conjunction with EN 62841-1:2015.
This Part 4-1 supplements or modifies the corresponding clauses in EN 62841-1:2015, so as to convert it
into the European Standard: Particular requirements for chain saws.
Where a particular subclause of Part 1 is not mentioned in this Part 4-1, that subclause applies as far as
relevant. When this standard states "addition", "modification" or "replacement", the relevant text in Part 1
is to be adapted accordingly.
The following print types are used:
- requirements: in roman type;
- test specifications: in italic type;
- notes: in smaller roman type.
The terms defined in Clause 3 are printed in bold typeface.
Subclauses, notes, tables and figures which are additional to those in Part 1 are numbered starting
from 101.
Clauses, subclauses, notes, tables, figures and annexes which are additional to those in
IEC 62841-4-1:2017 are prefixed “Z”.
2

---------------------- Page: 4 ----------------------
SIST EN 62841-4-1:2020
EN 62841-4-1:2020 (E)
This European Standard follows the overall requirements of EN ISO 12100.
This document has been prepared under a mandate given to CENELEC by the European Commission
and the European Free Trade Association and supports essential requirements of EU Directive(s).
For the relationship with EU Directive(s), see informative Annex ZZ, which is an integral part of this
document.
Compliance with the clauses of Part 1 together with this Part 4-1 provides one means of conforming with
the essential health and safety requirements of the Directive concerned.
Endorsement notice
The text of the International Standard IEC 62841-4-1:2017 was approved by CENELEC as a European
Standard with agreed common modifications.
3

---------------------- Page: 5 ----------------------
SIST EN 62841-4-1:2020
EN 62841-4-1:2020 (E)

COMMON MODIFICATIONS
1 Scope
Add the following to the existing Clause 1:
This standard covers all significant hazards, hazardous situations or hazardous events relevant for tools
covered by this standard.
NOTE Z101 Essential requirements not mentioned in Table ZZ.1 are deemed to be not applicable, because the corresponding
hazards are either not significant for tools covered by this standard or do not require specific action by the designer.

Annex I
Replace the title of Annex I with the following:
Annex I
(normative)

Measurement of noise and vibration emissions

and delete the note.

Replace I.2.5.3 with the following:
I.2.5.3 Battery powered chain saws shall be tested with a fully charged battery using a saw
chain and the longest guide bar combination(s) as specified in 8.14.2 c) 101), under both of the
following conditions:
– no-load speed, with the highest setting of the speed control, if any; and
– at maximum speed, by applying, if necessary, an adjustable load by means of a water brake
(or equivalent) as specified in A.2.1 of ISO 22868:2011, which is increased starting from zero
(no-load) until the maximum speed is achieved.
NOTE The use of the adjustable load is only necessary for machines where the maximum speed occurs at part load.
For machines, where the maximum speed occurs at no-load, the application of an adjustable load is not necessary.
Four consecutive sound power level tests at no-load speed and four at maximum speed shall be
carried out. The resulting sound power level L is calculated by:
WA
1
0,1LL0,1
W1 W2
 dB
L 10 lg 10+ 10
WA

2
where
is the arithmetic mean, rounded to the nearest decibel, of the four sound power level tests
L
W1
performed at no-load speed; and
4
=

---------------------- Page: 6 ----------------------
SIST EN 62841-4-1:2020
EN 62841-4-1:2020 (E)
L is the arithmetic mean, rounded to the nearest decibel, of the four sound power level tests
W2
performed at maximum speed.
During measurements, the machine shall operate under stable conditions. Once the noise
emission is steady, the measurement time interval shall be at least 15 s. If measurements are to
be made in octave or one-third octave frequency bands, the minimum period of observation shall
be 30 s for the frequency bands centred on or below 160 Hz, and 15 s for the frequency bands
centred on or above 200 Hz.


Annex K
(normative)

Battery tools and battery packs

K.1 Scope
Replace Note 102 with the following normative text:
This annex does not apply to chain saws equipped with integral batteries and with a maximum speed
of the saw chain exceeding 5 m/s.

Replace Subclause K.21.18 with the following:
K.21.18.Z101 Isolation and disabling device
Machines with an integral battery shall either be equipped
– with an isolation device to prevent the risk of injury from mechanical hazards during servicing or user
maintenance; or
– with a disabling device that prevents unintentional starting of the machine.
An isolation device shall
– provide disconnection of all poles of the battery from the serviceable region of the machine;
– be equipped with an unambiguous indication of the state of the disconnection device which
corresponds to each position of its manual control (actuator);
– be provided with protection against accidental reconnection.
NOTE 1 Examples of methods to achieve this disconnection include removable jumpers, integral batteries that can be
disconnected for servicing or user maintenance, or an electromechanical power switch with a direct mechanical link between the
actuator and the contact.
NOTE 2 The risk of accidental reconnection for a power switch is addressed by the requirement of 21.18.102. The other
examples in NOTE 1 achieve this by the necessary actions for reconnection.
A disabling device may be achieved by any of the following:
– a self-restoring or non-self-restoring lock-off device where two separate and dissimilar actions are
necessary before the motor is switched on (e.g. a power switch which has to be pushed in before it
5

---------------------- Page: 7 ----------------------
SIST EN 62841-4-1:2020
EN 62841-4-1:2020 (E)

can be moved laterally to close the contacts to start the motor). It shall not be possible to achieve
these two actions with a single grasping motion or a straight-line motion;
– a removable disabling device provided with the machine where it shall not be possible for the
machine to be operated when either applied or removed.
Compliance is checked by inspection and by manual test.

Annex L
(normative)

Battery tools and battery packs provided with mains connection or non-
isolated sources

L.1 Scope
Replace Note 102 with the following normative text:
This annex does not apply to chain saws equipped with integral batteries and with a maximum speed
of the saw chain exceeding 5 m/s.

Replace Subclause L.21.18 with the following:
L.21.18.Z101 Isolation and disabling device
Machines with an integral battery shall either be equipped
– with an isolation device to prevent the risk of injury from mechanical hazards during servicing or user
maintenance; or
– with a disabling device that prevents unintentional starting of the machine.
An isolation device shall
– provide disconnection of all poles of the battery from the serviceable region of the machine;
– be equipped with an unambiguous indication of the state of the disconnection device which
corresponds to each position of its manual control (actuator);
– be provided with protection against accidental reconnection.
NOTE 1 Examples of methods to achieve this disconnection include removable jumpers, integral batteries that can be
disconnected for servicing or user maintenance, or an electromechanical power switch with a direct mechanical link between the
actuator and the contact.
NOTE 2 The risk of accidental reconnection for a power switch is addressed by the requirement of 21.18.102. The other
examples in NOTE 1 achieve this by the necessary actions for reconnection.
A disabling device may be achieved by any of the following:
– a self-restoring or non-self-restoring lock-off device where two separate and dissimilar actions are
necessary before the motor is switched on (e.g. a power switch which has to be pushed in before it
can be moved laterally to close the contacts to start the motor). It shall not be possible to achieve
these two actions with a single grasping motion or a straight-line motion;
6

---------------------- Page: 8 ----------------------
SIST EN 62841-4-1:2020
EN 62841-4-1:2020 (E)
– a removable disabling device provided with the machine where it shall not be possible for the
machine to be operated when either applied or removed.
Compliance is checked by inspection and by manual test.

7

---------------------- Page: 9 ----------------------
SIST EN 62841-4-1:2020
EN 62841-4-1:2020 (E)

Add the following annexes:
Annex ZA
(normative)

Normative references to international publications
with their corresponding European publications
The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any amendments) applies.
NOTE 1 When an International Publication has been modified by common modifications, indicated by (mod), the
relevant EN/HD applies.
NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is available
here: www.cenelec.eu.
This annex from EN 62841-1:2015 is applicable with the following addition:
Publication Year Title EN/HD Year
IEC 61672-1 - Electroacoustics – Sound level meters – EN 61672-1 2013
Part 1: Specifications
ISO 354 2003 Acoustics – Measurement of sound EN ISO 354 2003
absorption in a reverberation room
ISO 3744 2010 Acoustics – Determination of sound power EN ISO 3744 2010
levels and sound energy levels of noise
sources using sound pressure – Engineering
methods for an essentially free field over a
reflecting plane
ISO 6533 2012 Forestry machinery – Portable chain-saw - -
front hand-guard – Dimensions and
clearances
ISO 6534 2007 Forestry machinery – Portable chain-saw - -
hand-guards – Mechanical strength
ISO 7914 2002 Forestry machinery – Portable chain saws – - -
Minimum handle clearance and sizes
ISO 7915 1991 Forestry machinery – Portable chain-saws – - -
Determination of handle strength
ISO 9518 - Forestry machinery – Portable chain-saws – - -
Kickback test
ISO 10726 1992 Portable chain-saws – Chain catcher – - -
Dimensions and mechanical strength
ISO 11681-2 2011 Machinery for forestry – Portable chain-saw EN ISO 11681-2 2011
safety requirements and testing –
Part 2: Chain-saws for tree service
ISO 13772 2018 Forestry machinery – Portable chain saws - - -
Non-manually actuated chain brake
performance
8

---------------------- Page: 10 ----------------------
SIST EN 62841-4-1:2020
EN 62841-4-1:2020 (E)
Publication Year Title EN/HD Year
ISO 17080 2005 Manually portable agricultural and forestry - -
machines and powered lawn and garden
equipment – Design principles for single-
panel product safety labels
ISO 22868 2011 Forestry and gardening machinery – Noise EN ISO 22868 2011
test code for portable hand-held machines
with internal combustion engine –
Engineering method (Grade 2 accuracy)

9

---------------------- Page: 11 ----------------------
SIST EN 62841-4-1:2020
EN 62841-4-1:2020 (E)

Annex ZZ
(informative)

Relationship between this European Standard and the essential requirements of
Directive 2006/42/EC [2006 OJ L157] aimed to be covered
This European Standard has been prepared under a Commission’s standardisation request M/396 to
provide one voluntary means of conforming to essential requirements of Directive 2006/42/EC of the
European Parliament and of the Council of 17 May 2006 on machinery, and amending
Directive 95/16/EC.
Once this standard is cited in the Official Journal of the European Union under that Directive, compliance
with the normative clauses of this standard given in Table ZZ.1 confers, within the limits of the scope of
this standard, a presumption of conformity with the corresponding essential requirements of that
Directive, and associated EFTA regulations.
Table ZZ.1 – Correspondence between this European Standard
and Annex I of Directive 2006/42/EC
Essential Requirements of Clause(s) / sub-clause(s) Remarks / Notes:
Directive 2006/42/EC of this EN
Description of
Clause numbers of Annex I requirements
1.1.2 4
(Principles of safety integration)
1.1.3 5, 6.1, 21.6, K/L.5, L.21
(Materials and products)
1.1.5 19.4, 19.101, 19.108, 19.111
(Design of machinery to facilitate
its handling)
1.1.6 5, 19.5, 19.111, 21.18, K/L.5,
(Ergonomics) K.21.301, L.21.301
1.2.1 5, 18.6, 18.8, 23.1.6, 23.1.10,
(Safety and reliability of control 23.1.11, 23.3, K/L.5, K.18.6, K/L.18.8,
systems) K/L.23.1.10, K.23.1.201, L.18
1.2.2 5, 8.5, 8.9, 8.10, 8.11, 21.1, 21.2,
(Control devices) 21.4, 21.17, 21.18, K/L.5,
K.21.17.1.2, L.21
1.2.3 5, 21.17, K/L.5, K.21.17.1.2, L.21
(Starting)
1.2.4.1 5, 21.17, K/L.5, K.21.17.1.2, L.21
(Normal stop)
1.2.6 5, 21.18.1.Z1, 21.18.2.1, 21.18.101,
(Failure of the power supply) 23.3, K/L.5, L.21
1.3.2 5, 8.14.2 c), 13.1, 14.4, 17, 19.109,
(Risk of break-up during 19.110, 20, 21.23, 24.11, 24.12,
operation) 24.13, 27, K/L.5, K/L.13.1, K/L.17,
K/L.20, K/L.24.201, K.27.1, L.21
10

---------------------- Page: 12 ----------------------
SIST EN 62841-4-1:2020
EN 62841-4-1:2020 (E)
Essential Requirements of Clause(s) / sub-clause(s) Remarks / Notes:
Directive 2006/42/EC of this EN
Description of
Clause numbers of Annex I requirements
1.3.3 5, 18.3, 19.109, 19.110, K/L.5, L.18
(Risk due to falling or ejected
objects)
1.3.4 19.2, 21.24, L.21
(Risks due to surfaces, edges or
angles)
1.3.7 5, 19.1, 19.3, 19.102, 19.103, 19.104,
(Risks related to moving parts) 19.105, 19.107, 19.108, K/L.5
1.3.8.1 5, 19.1, 19.3, 19.104, K/L.5
(Moving transmission parts)
1.3.8.2 5, 19.1, 19.102, 19.103, K/L.5
(Moving parts involved in the
process)
1.4.1 5, 19.1, 19.102, 19.103, 19.104,
(General requirements (for 19.105, 19.107, 19.108, 20.1, 20.2,
guards and protective devices)) 20.3, 20.4, 20.102, 20.103, 21.22,
K/L.5, K.20.1, K.20.3, L.20, L.21
1.4.2.1 5, 19.1, 19.9, K/L.5
(Special requirements for fixed
guards)
1.4.2.3 5, 19.1, K/L.5
(Special requirements for
adjustable guards restricting
access)
1.5.1 5, 7, L.7.1, 9, 10, 11, 12, 14, 15, 16,
(Risks due to electricity supply) 17, 18.1 -18.7, 20.5, 21.3, 21.5 –
21.16, 21.19 - 21.22, 21.25 - 21.34,
22, 23.1.1 - 23.1.5, 23.1.7 - 23.1.9,
23.2, 23.4, 23.5, 24, 25, 26, 27, 28,
K/L.5, K.7, K/L.9, K/L.10, K/L.11,
K/L.12, K/L.14, K/L.16, K/L.17, K.18.1
– K.18.7, K.21.5 – K.21.16, K.21.19 –
K.21.22, K.21.25 – K.21.34, K/L.22,
K/L.24, K/L.25, K/L.26, K.27.1,
K/L.28.1, K.28.2, L.18, L.18.201,
L.20, L.21, Annex C
1.5.4 5, 8.7, 8.8, 8.13, 8.14.2, 21.7, 21.8,
(Risks due to errors of fitting) 21.19, 27.1, K/L.5, K.8.7, K.8.8,
K/L.19.201, K/L.21.201, K/L.21.203,
K.27.1, L.21
1.5.5 5, 12.5, K/L.5, K.12.1
(Risks due to extreme
temperatures)
11

---------------------- Page: 13 ----------------------
SIST EN 62841-4-1:2020
EN 62841-4-1:2020 (E)

Essential Requirements of Clause(s) / sub-clause(s) Remarks / Notes:
Directive 2006/42/EC of this EN
Description of
Clause numbers of Annex I requirements
1.5.6 5, 13, 18.1, 18.2, 18.4, 18.6, 28.1,
(Risks due to fire) K/L.5, K/L.13, K/L.12.201, K.18.1,
K.18.6, K/L.18.201, K/L.18.202,
K/L.18.203, K.20.1, K.20.3,
K/L.21.201, K/L.21.203, K/L.23.201,
K/L.23.202, K/L.28.1, L.18, L.18.204,
L.20.201, L.20.202, L.28.201
1.5.7 5, K/L.5, K/L.12.201, K.18.201,
(Risks due to explosion) K/L.18.202, K/L.18.203, K/L.19.202,
K.20.1, K.20.3, K/L.21.202,
K/L.21.203, L.18.204, L.20.201,
L.20.202
1.5.8 I.2.Z1
(Risks due to noise)
1.5.9 I.3.Z1
(Risks due to vibrations)
1.5.10 5, 6.1, 6.3, K/L.5
(Risks due to radiation)
1.5.11 5, 18.8, K/L.5, K/L.18.8
(Risks due to external radiation)
1.5.12 6.2
(Risks due to laser radiation)
1.6.1 24.1, K.21.18.Z101, L.21.18.Z101
(Machinery maintenance)
1.6.3 24.1, K.21.18.Z101, L.21.18.Z101
(Isolation of energy sources)
1.7.1 8.1, 8.4, 8.6, K/L.8.1, K/L.8.2
(Information and warnings on
machinery)
1.7.1.1 8.2, 8.4, K/L.8.4
(Information and information
devices)
1.7.2 8.2
(Warning of residual risks)
1.7.3 8.3, 8.4, 8.12, K/L.8.3, K/L.8.4
(Marking of machinery)
1.7.4 8.14, K/L.8.14.1.1, K/L.8.14.2
(Instructions)
2.2.1 5, 19.4, 19.5, 19.101, 21.18, K/L.5,
(General requirements for L.21
portable hand-held and/or hand-
guided machinery)
2.2.1.1 5, 8.14.2 Za) 3), I.3.6.2, K/L.5
(Instructions for portable hand-
held and/or hand-guided
machinery)
12

---------------------- Page: 14 ----------------------
SIST EN 62841-4-1:2020
EN 62841-4-1:2020 (E)
Essential Requirements of Clause(s) / sub-clause(s) Remarks / Notes:
Directive 2006/42/EC of this EN
Description of
Clause numbers of Annex I requirements
2.3 19.107, 19.112
(Machinery for working wood and
similar material)
WARNING 1: Presumption of conformity stays valid only as long as a reference to this European
standard is maintained in the list published in the Official Journal of the European Union. Users of this
standard should consult frequently the latest list published in the Official Journal of the European Union.
WARNING 2: Other Union legislation may be applicable to the product(s) falling within the scope of this
standard.
13

---------------------- Page: 15 ----------------------
SIST EN 62841-4-1:2020

---------------------- Page: 16 ----------------------
SIST EN 62841-4-1:2020

IEC 62841-4-1
®

Edition 1.0 2017-10
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
colour
inside


Electric motor-operated hand-held tools, transportable tools and lawn and
garden machinery – Safety –
Part 4-1: Particular requirements for chain saws

Outils électroportatifs à moteur, outils portables et machines pour jardins et
pelouses – Sécurité –
Partie 4-1: Exigences particulières pour les scies à chaîne

IEC 62841-4-1:2017-10(en-fr)

---------------------- Page: 17 ----------------------
SIST EN 62841-4-1:2020




IEC 62841-4-1

®


Edition 1.0 2017-10




INTERNATIONAL



STANDARD




NORME



INTERNATIONALE
colour

inside










Electric motor-operated hand-held tools, transportable tools and lawn and

garden machinery – Safety –

Part 4-1: Particular requirements for chain saws




Outils électroportatifs à moteur, outils portables et machines pour jardins et

pelouses – Sécurité –


Partie 4-1: Exigences particulières pour les scies à chaîne













INTERNATIONAL

ELECTROTECHNICAL

COMMISSION


COMMISSION

ELECTROTECHNIQUE


INTERNATIONALE




ICS 25.140.20 ISBN 978-2-8322-4754-9



Warning! Make sure that you obtained this publication from an authorized distributor.

Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agréé.

® Registered trademark of the International Electrotechnical Commission
Marque déposée de la Commission Electrotechnique Internationale

---------------------- Page: 18 ----------------------
SIST EN 62841-4-1:2020
– 2 – IEC 62841-4-1:2017 © IEC 2017
CONTENTS
FOREWORD . 4
1 Scope . 6
2 Normative references . 6
3 Terms and definitions . 7
4 General requirements . 8
5 General conditions for the tests . 8
6 Radiation, toxicity and similar hazards . 9
7 Classification . 9
8 Marking and instructions . 9
9 Protection against access to live parts . 12
10 Starting . 12
11 Input and current . 12
12 Heating . 12
13 Resistance to heat and fire . 12
14 Moisture resistance . 12
15 Resistance to rusting . 13
16 Overload protection of transformers and associated circuits . 13
17 Endurance . 13
18 Abnormal operation . 13
19 Mechanical hazards . 14
20 Mechanical strength . 19
21 Construction . 20
22 Internal wiring . 22
23 Components . 22
24 Supply connection and external flexible cords . 23
25 Terminals for external conductors . 24
26 Provision for earthing . 24
27 Screws and connections . 24
28 Creepage distances, clearances and distances through insulation . 24
Annexes . 30
Annex I (informative) Measurement of noise and vibration emissions . 30
Annex K (normative) Battery tools and battery packs . 37
Annex L (normative) Battery tools and battery packs provided with mains connection
or non-isolated sources . 42
Annex AA (normative) Safety signs . 46
Annex BB (informative) Examples of instructions concerning the proper techniques for
basic felling, limbing, and cross-cutting . 48
Annex CC (informative) Example of a material and construction for fulfilling the
requirements for an artificial surface . 52
Bibliography . 54

Figure 101 – Chain saw nomenclature . 24
Figure 102 – Cutting length .
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.