Radio-frequency connectors - Part 61: Sectional specification for RF coaxial connectors with 9,5 mm inner diameter of outer conductor, quick lock coupling, series Q4.1-9.5 (IEC 61169-61:2020)

This part of IEC 61169, which is a sectional specification (SS), provides information and rules
for the preparation of detail specifications (DS) for coaxial connectors with a 9,5 mm inner
diameter of the outer conductor and quick lock coupling mechanism, characteristic impedance
50 Ω and an operating frequency of up to 8,5 GHz. Series Q4.1-9.5 connectors with socket
centre contact are compatible with threaded 4,1-9,5 series (specified in IEC 60169-11)
connectors with pin centre contact. This type of connectors are starting to be applied in
telecommunication systems due to their special features which are suitable for outdoor harsh
requirements, such as quick and reliable coupling, compatible with threaded connector and
being entirely waterproof.
This document specifies mating face dimensions for general purpose connectors – grade 2,
dimensional details of standard test connectors – grade 0, gauge information and test
requirements, product ratings and characteristics, tests selected from IEC 61169-1, applicable
to all detail specifications relating to Q4.1-9.5 series RF coaxial connectors.
Annex A specifies the outline dimensions of connectors and protective sleeves, which could
bring interchangeability between pairs of connectors and protective sleeves from different
manufacturers.
This document indicates the recommended performance characteristics to be considered
when writing a detail specification and covers test schedules and inspection requirements for
assessment levels M and H.
NOTE Metric dimensions are original dimensions. All undimensioned pictorial configurations are for reference
purposes only.

Hochfrequenz-Steckverbinder - Teil 61: Rahmenspezifikation für koaxiale HF-Steckverbinder mit 9,5 mm Innendurchmesser des Außenleiters und Schnellverschlusskupplung der Serie Q4.1-9.5 (IEC 61169-61:2020)

Connecteurs pour fréquences radioélectriques - Partie 61 : Spécification intermédiaire relative aux connecteurs coaxiaux pour fréquences radioélectriques avec diamètre intérieur du conducteur extérieur de 9,5 mm avec verrouillage rapide, série Q4.1-9.5 (IEC 61169-61:2020)

l’IEC 61169-61:2020, qui est une spécification intermédiaire (SS, en anglais Sectional Specification), fournit des informations et des règles pour l’établissement de spécifications particulières (DS, en anglais Detail Specification) pour les connecteurs coaxiaux avec un diamètre intérieur du conducteur extérieur de 9,5 mm et un mécanisme de verrouillage rapide, une impédance caractéristique de 50 Ω, et une fréquence de fonctionnement allant jusqu’à 8,5 GHz. Les connecteurs de série Q4.1-9.5 disposant d’un contact central en embase sont compatibles avec les connecteurs filetés de série 4.1-9.5 (spécifié dans l’IEC 60169-11) disposant d’un contact central en broche. Ces types de connecteurs commencent à être utilisés dans des systèmes de télécommunication car leurs fonctionnalités spéciales, telles qu’un couplage rapide et fiable, une compatibilité avec les connecteurs filetés et une étanchéité totale, conviennent aux exigences rigoureuses d’une utilisation en extérieur.
Ce document spécifie les dimensions de la face d’accouplement pour les connecteurs à usage général (grade 2), les détails dimensionnels des connecteurs d’essai normalisé (grade 0), les informations du calibre et les exigences d’essai, les valeurs assignées et les caractéristiques du produit, les essais choisis à partir de l’IEC 61169-1, applicables à toutes les spécifications particulières relatives aux connecteurs coaxiaux pour fréquences radioélectriques de série Q4.1-9.5.
Ce document indique les caractéristiques de performance recommandées à considérer lors de l’écriture d’une spécification particulière et il couvre les programmes d’essai et les exigences de contrôle pour les niveaux d’assurance M et H.

Radiofrekvenčni konektorji - 61. del: Področna specifikacija za radiofrekvenčne (RF) koaksialne konektorje z notranjim premerom zunanega vodnika 9,5 mm, hitra zaklepna sponka, serije Q4.1–9.5 (IEC 61169-61:2020)

General Information

Status
Published
Publication Date
02-Sep-2020
Technical Committee
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
12-Aug-2020
Due Date
17-Oct-2020
Completion Date
03-Sep-2020

Buy Standard

Standard
EN IEC 61169-61:2020
English language
34 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN IEC 61169-61:2020
01-oktober-2020
Radiofrekvenčni konektorji - 61. del: Področna specifikacija za radiofrekvenčne
(RF) koaksialne konektorje z notranjim premerom zunanega vodnika 9,5 mm, hitra
zaklepna sponka, serije Q4.1–9.5 (IEC 61169-61:2020)
Radio-frequency connectors - Part 61: Sectional specification for RF coaxial connectors
with 9,5 mm inner diameter of outer conductor, quick lock coupling, series Q4.1-9.5 (IEC
61169-61:2020)
Hochfrequenz-Steckverbinder - Teil 61: Rahmenspezifikation für koaxiale HF-
Steckverbinder mit 9,5 mm Innendurchmesser des Außenleiters und
Schnellverschlusskupplung der Serie Q4.1-9.5 (IEC 61169-61:2020)
Connecteurs pour fréquences radioélectriques - Partie 61 : Spécification intermédiaire
relative aux connecteurs coaxiaux pour fréquences radioélectriques avec diamètre
intérieur du conducteur extérieur de 9,5 mm avec verrouillage rapide, série Q4.1-9.5
(IEC 61169-61:2020)
Ta slovenski standard je istoveten z: EN IEC 61169-61:2020
ICS:
33.120.30 Radiofrekvenčni konektorji RF connectors
(RF)
SIST EN IEC 61169-61:2020 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN IEC 61169-61:2020

---------------------- Page: 2 ----------------------
SIST EN IEC 61169-61:2020


EUROPEAN STANDARD EN IEC 61169-61

NORME EUROPÉENNE

EUROPÄISCHE NORM
July 2020
ICS 33.120.30

English Version
Radio-frequency connectors - Part 61: Sectional specification for
RF coaxial connectors with 9,5 mm inner diameter of outer
conductor, quick lock coupling, series Q4.1-9.5
(IEC 61169-61:2020)
Connecteurs pour fréquences radioélectriques - Partie 61: Hochfrequenz-Steckverbinder - Teil 61:
Spécification intermédiaire relative aux connecteurs Rahmenspezifikation für koaxiale HF-Steckverbinder mit 9,5
coaxiaux pour fréquences radioélectriques avec diamètre mm Innendurchmesser des Außenleiters und
intérieur du conducteur extérieur de 9,5 mm, verrouillage Schnellverschlusskupplung der Serie Q4.1-9.5
rapide, série Q4.1-9.5 (IEC 61169-61:2020)
(IEC 61169-61:2020)
This European Standard was approved by CENELEC on 2020-07-01. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.


European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2020 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
 Ref. No. EN IEC 61169-61:2020 E

---------------------- Page: 3 ----------------------
SIST EN IEC 61169-61:2020
EN IEC 61169-61:2020 (E)
European foreword
The text of document 46F/492/FDIS, future edition 1 of IEC 61169-61, prepared by SC 46F "RF and
microwave passive components" of IEC/TC 46 "Cables, wires, waveguides, RF connectors, RF and
microwave passive components and accessories" was submitted to the IEC-CENELEC parallel vote
and approved by CENELEC as EN IEC 61169-61:2020.
The following dates are fixed:
• latest date by which the document has to be implemented at national (dop) 2021-04-01
level by publication of an identical national standard or by endorsement
• latest date by which the national standards conflicting with the (dow) 2023-07-01
document have to be withdrawn

Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.

Endorsement notice
The text of the International Standard IEC 61169-61:2020 was approved by CENELEC as a European
Standard without any modification.


2

---------------------- Page: 4 ----------------------
SIST EN IEC 61169-61:2020
EN IEC 61169-61:2020 (E)
Annex ZA
(normative)

Normative references to international publications
with their corresponding European publications
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments)
applies.
NOTE 1  Where an International Publication has been modified by common modifications, indicated by (mod), the relevant
EN/HD applies.
NOTE 2  Up-to-date information on the latest versions of the European Standards listed in this annex is available here:
www.cenelec.eu.
Publication Year Title EN/HD Year
IEC 60529 - Degrees of protection provided by enclosures - -
(IP Code)
IEC 61169-1 2013 Radio frequency connectors - Part 1: Generic EN 61169-1 2013
specification - General requirements and
measuring methods
IEC 62037-3 2012 Passive RF and microwave devices, EN 62037-3 2012
intermodulation level measurement - Part 3:
Measurement of passive intermodulation in
coaxial connectors

3

---------------------- Page: 5 ----------------------
SIST EN IEC 61169-61:2020

---------------------- Page: 6 ----------------------
SIST EN IEC 61169-61:2020



IEC 61169-61

®


Edition 1.0 2020-05




INTERNATIONAL



STANDARD




NORME


INTERNATIONALE











Radio-frequency connectors –

Part 61: Sectional specification for RF coaxial connectors with 9,5 mm inner

diameter of outer conductor, quick lock coupling, series Q4.1-9.5



Connecteurs pour fréquences radioélectriques –

Partie 61: Spécification intermédiaire relative aux connecteurs coaxiaux pour


fréquences radioélectriques avec diamètre intérieur du conducteur extérieur

de 9,5 mm, verrouillage rapide, série Q4.1-9.5












INTERNATIONAL

ELECTROTECHNICAL

COMMISSION


COMMISSION

ELECTROTECHNIQUE


INTERNATIONALE




ICS 33.120.30 ISBN 978-2-8322-8238-0




Warning! Make sure that you obtained this publication from an authorized distributor.

Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agréé.

® Registered trademark of the International Electrotechnical Commission
Marque déposée de la Commission Electrotechnique Internationale

---------------------- Page: 7 ----------------------
SIST EN IEC 61169-61:2020
– 2 – IEC 61169-61:2020 © IEC 2020
CONTENTS
FOREWORD . 4
1 Scope . 6
2 Normative references . 6
3 Terms and definitions . 7
4 Mating face and gauge information . 7
4.1 General connectors – Grade 2 . 7
4.1.1 Connector with pin centre contact . 7
4.1.2 Connector with socket centre contact . 8
4.2 Gauges . 10
4.2.1 Gauge pin for socket centre contact. 10
4.2.2 Gauge rings for plug outer contact . 11
4.3 Standard test connectors – Grade 0 . 12
4.3.1 Standard test connector with pin centre contact . 12
4.3.2 Standard test connector with socket centre contact . 14
5 Quality assessment procedure . 15
5.1 General . 15
5.2 Rating and characteristics (see Clause 5 of IEC 61169-1:2013) . 15
5.3 Test schedule and inspection requirements. 18
5.3.1 Acceptance tests (See Table 8) . 18
5.3.2 Periodic tests (See Table 9). 18
5.4 Procedures for qualification approval . 20
5.4.1 Quality conformance inspection . 20
5.4.2 Qualification approval and its maintenance . 20
5.4.3 Periodic tests . 20
6 Instructions for preparation of detail specifications . 20
6.1 General . 20
6.2 Identification of the component . 21
6.3 Performance . 21
6.4 Marking, ordering information and related matters . 21
6.5 Selection of tests, test conditions and severities . 21
6.6 Blank detail specification pro-forma for Q4.1-9.5 connectors . 21
7 Marking . 26
7.1 Marking of component . 26
7.2 Marking and contents of package . 26
Annex A (informative)  Q4.1-9.5 series quick lock RF coaxial connectors protective
sealing . 27
A.1 General . 27
A.2 The outline of connector . 27
A.2.1 The outline of cable connector . 27
A.2.2 The outline of panel connector(socket) . 28
A.3 Protective sleeves . 29
A.3.1 Protective sleeve of cable connector. 29
A.3.2 Protective sleeve of panel connector . 29
Bibliography . 31

Figure 1 – Connector with pin centre contact . 7

---------------------- Page: 8 ----------------------
SIST EN IEC 61169-61:2020
IEC 61169-61:2020 © IEC 2020 – 3 –
Figure 2 – Connector with socket centre contact . 9
Figure 3 – Gauge pin for socket centre contact . 10
Figure 4 – Gauge ring for plug outer contact . 11
Figure 5 – Standard test connector with pin–centre contact . 13
Figure 6 – Standard test connector with socket centre contact . 14
Figure A.1 – Cable connector(plug) outline . 27
Figure A.2 – Cable connector(socket) outline . 28
Figure A.3 – Panel connector outline . 28
Figure A.4 – Protective sleeve outline . 29
Figure A.5 – Panel style protective sleeve outline . 30

Table 1 – Dimensions of connector with pin centre contact . 8
Table 2 – Dimensions of connector with socket centre contact . 10
Table 3 – Dimensions of gauge pin for socket centre contact . 11
Table 4 – Dimensions of gauge rings for plug outer contact . 12
Table 5 – Dimensions of standard test connector with pin-centre contact . 13
Table 6 – Dimensions of standard test connector with socket centre contact . 15
Table 7 –Ratings and characteristics . 16
Table 8 – Acceptance tests . 18
Table 9 – Periodic tests . 19
Table A.1 – Cable connector(plug) dimensions . 27
Table A.2 – Cable connector(socket) dimensions . 28
Table A.3 – Panel connector dimensions . 29
Table A.4 – Protective sleeve dimensions . 29
Table A.5 – Panel style protective sleeve dimensions . 30

---------------------- Page: 9 ----------------------
SIST EN IEC 61169-61:2020
– 4 – IEC 61169-61:2020 © IEC 2020
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________

RADIO-FREQUENCY CONNECTORS –

Part 61: Sectional specification for RF coaxial connectors with 9,5 mm
inner diameter of outer conductor, quick lock coupling, series Q4.1-9.5

FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 61169-61 has been prepared by subcommittee 46F: RF and
microwave passive components, of IEC technical committee 46: Cables, wires, waveguides,
RF connectors, RF and microwave passive components and accessories.
The text of this International Standard is based on the following documents:
FDIS Report on voting
46F/492/FDIS 46F/494/RVD

Full information on the voting for the approval of this International Standard can be found in
the report on voting indicated in the above table.
This document has been drafted in accordance with the ISO/IEC Directives, Part 2.

---------------------- Page: 10 ----------------------
SIST EN IEC 61169-61:2020
IEC 61169-61:2020 © IEC 2020 – 5 –
A list of all parts in the IEC 61169 series, published under the general title Radio-frequency
connectors, can be found on the IEC website.
The committee has decided that the contents of this document will remain unchanged until the
stability date indicated on the IEC website under "http://webstore.iec.ch" in the data related to
the specific document. At this date, the document will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.

---------------------- Page: 11 ----------------------
SIST EN IEC 61169-61:2020
– 6 – IEC 61169-61:2020 © IEC 2020
RADIO-FREQUENCY CONNECTORS –

Part 61: Sectional specification for RF coaxial connectors with 9,5 mm
inner diameter of outer conductor, quick lock coupling, series Q4.1-9.5



1 Scope
This part of IEC 61169, which is a sectional specification (SS), provides information and rules
for the preparation of detail specifications (DS) for coaxial connectors with a 9,5 mm inner
diameter of the outer conductor and quick lock coupling mechanism, characteristic impedance
50 Ω and an operating frequency of up to 8,5 GHz. Series Q4.1-9.5 connectors with socket
centre contact are compatible with threaded 4,1-9,5 series (specified in IEC 60169-11)
connectors with pin centre contact. This type of connectors are starting to be applied in
telecommunication systems due to their special features which are suitable for outdoor harsh
requirements, such as quick and reliable coupling, compatible with threaded connector and
being entirely waterproof.
This document specifies mating face dimensions for general purpose connectors – grade 2,
dimensional details of standard test connectors – grade 0, gauge information and test
requirements, product ratings and characteristics, tests selected from IEC 61169-1, applicable
to all detail specifications relating to Q4.1-9.5 series RF coaxial connectors.
Annex A specifies the outline dimensions of connectors and protective sleeves, which could
bring interchangeability between pairs of connectors and protective sleeves from different
manufacturers.
This document indicates the recommended performance characteristics to be considered
when writing a detail specification and covers test schedules and inspection requirements for
assessment levels M and H.
NOTE Metric dimensions are original dimensions. All undimensioned pictorial configurations are for reference
purposes only.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their
content constitutes requirements of this document. For dated references, only the edition
cited applies. For undated references, the latest edition of the referenced document (including
any amendments) applies.
IEC 60529, Degrees of protection provided by enclosures (IP Code)
IEC 61169-1:2013, Radio-frequency connectors – Part 1: Generic specification – General
requirements and measuring methods
IEC 62037-3:2012, Passive RF and microwave devices, intermodulation level measurement –
Part 3: Measurement of passive intermodulation in coaxial connectors

---------------------- Page: 12 ----------------------
SIST EN IEC 61169-61:2020
IEC 61169-61:2020 © IEC 2020 – 7 –
3 Terms and definitions
No terms and definitions are listed in this document.
ISO and IEC maintain terminological databases for use in standardization at the following
addresses:
• IEC Electropedia: available at http://www.electropedia.org/
• ISO Online browsing platform: available at http://www.iso.org/obp
4 Mating face and gauge information
4.1 General connectors – Grade 2
4.1.1 Connector with pin centre contact
The mating face of a connector with pin centre contact is shown as Figure 1 and its
dimensions are shown as Table 1.

a
Mechanical and electrical plane.
Figure 1 – Connector with pin centre contact

---------------------- Page: 13 ----------------------
SIST EN IEC 61169-61:2020
– 8 – IEC 61169-61:2020 © IEC 2020
Table 1 – Dimensions of connector with pin centre contact
mm
Ref.
Min. Max.
a 22,32 22,52
b 19,78 19,90
a
c — —
d 9,45 9,55
e 13,70 13,75
f 16,80 16,90
b
g 1,99 2,01
c
h — —
i 1,20 1,40
j 0,57 0,97
k 1,20 1,42
l 6,15 6,25
m 8,49 8,59
n 13,58 14,08
d
p 4,13 (nominal)
q 2,855 2,945
s 4,00 5,00
t 2,50 3,00
w 0,20 0,50
a
Resilient electrical contact, slot design meet 4.3.3 requirements.
b
Stainless steel or ceramic beads, not less than 5pcs, radially and uniformly
distributed.
c
Sealing ring design optional and should meet sealing performance.
d
The tolerance on this dimension is determined by the tolerance of characteristic
impedance.

4.1.2 Connector with socket centre contact
The mating face of a connector with socket centre contact is shown as Figure 2 and its
dimensions are shown as Table 2.

---------------------- Page: 14 ----------------------
SIST EN IEC 61169-61:2020
IEC 61169-61:2020 © IEC 2020 – 9 –

a
Mechanical and electrical plane.
b
Ring identification tank and painted with red mark.
Figure 2 – Connector with socket centre contact

---------------------- Page: 15 ----------------------
SIST EN IEC 61169-61:2020
– 10 – IEC 61169-61:2020 © IEC 2020
Table 2 – Dimensions of connector with socket centre contact
mm
Ref.
Min. Max.
a 19,69 19,74
b 18,09 18,15
c 9,45 9,55
d 12,03 12,13
e 13,80 13,85
f 18,28 18,32
g 14,40 —
h 8,49 8,59
i 1,17 1,47
j 1,60 1,90
k 4,65 4,75
l 6,15 6,25
m 6,70 —
n 2,18 2,24
a
p — —
b
q 4,13 (nominal)
s 5,00 —
t 16,50 16,70
u 0,40 0,50
v 0,45 0,65
w 1,60 1,80
a
The resilient electrical contact, slot design optional, should meet 4.2.1
requirements.
b
The tolerance on this dimension is determined by the tolerance of characteristic
impedance.

4.2 Gauges
4.2.1 Gauge pin for socket centre contact
4.2.1.1 General
The gauge pin for socket centre contact is shown as Figure 3 and its dimensions are shown
as Table 3.

Figure 3 – Gauge pin for socket centre contact

---------------------- Page: 16 ----------------------
SIST EN IEC 61169-61:2020
IEC 61169-61:2020 © IEC 2020 – 11 –
Table 3 – Dimensions of gauge pin for socket centre contact
Gauge A Gauge B Gauge C
(For sizing purpose) (For insertion purpose) (For retention purpose)
Ref.
+5
Mass of gauge:150 0 g
Min. Max. Min. Max. Min. Max.
a 2,945 2,950 2,940 2,945 2,850 2,855
b 2,0 2,2 2,0 2,2 2,0 2,2
c 3,3 3,5 3,3 3,5 3,3 3,5
Material: steel, polished.

4.2.1.2 Test procedure
Test procedure is as follows.
a) Sizing test
The gauge A should be inserted in the socket centre contact three times, this is a sizing
operation.
b) Insertion test
Following the sizing operation, if specified in the detail specification, the force necessary
to insert Gauge B fully into the socket centre contact shall be measured. When this test is
required, the insertion force shall not exceed 15 N.
c) Retention test
After sizing or insertion test, the gauge C shall be inserted into the socket centre contact.
The contact shall retain the mass of the gauge C in a vertical downward position. When
this test is required, the retention force shall be not less than 1,5 N.
4.2.2 Gauge rings for plug outer contact
4.2.2.1 General
The gauge rings for plug outer contact is shown as Figure 4 and its dimensions are shown as
Table 4.

Figure 4 – Gauge ring for plug outer contact

---------------------- Page: 17 ----------------------
SIST EN IEC 61169-61:2020
– 12 – IEC 61169-61:2020 © IEC 2020
Table 4 – Dimensions of gauge rings for plug outer contact
Gauge A Gauge B Gauge C
(For sizing purpose) (For insertion purpose) (For retention purpose)
Ref. +5
Mass of gauge: 400 g
 0
Min. Max. Min. Max. Min. Max.
a 12,13 12,135 12,125 12,13 12,03 12,035
b 4,65 4,75 4,65 4,75 4,65 4,75
c 6,65 — 6,65 — 6,65 —
d 12,69 12,80 12,69 12,80 12,69 12,80
e 15,00 — 15,00 — 15,00 —
Material steel, polished.

4.2.2.2 Test procedure
Test procedure is as follows.
a) Sizing test
The gauge A should be inserted in the outer contact three times, this is a sizing operation.
b) Insertion test
Following the sizing operation, if specified in the detail specification, the force necessary
to insert Gauge B fully into the outer contact shall be measured. When this test is required,
the insertion force shall not exceed 35 N.
c) Retention test
After sizing or insertion test, the gauge C shall be inserted into the outer contact. The
contact shall retain the mass of the gauge C in a vertical downward position. When this
test is required, the retention force shall be not less than 4 N.
4.3 Standard test connectors – Grade 0
4.3.1 Standard test connector with pin centre contact
The mating face of a standard test connector with pin centre contact is shown as Figure 5 and
its dimensions are shown as Table 5.

---------------------- Page: 18 ----------------------
SIST EN IEC 61169-61:2020
IEC 61169-61:2020 © IEC 2020 – 13 –

a
Mechanical and electrical plane.
Figure 5 – Standard test connector with pin–centre contact
Table 5 – Dimensions of standard test connector with pin-centre contact
mm
Ref.
Min. Max.
a 22,32 22,52
b 19,78 19,90
a
c — —
d 9,500 9,510
e 13,70 13,75
b
g 1,99 2,01
i 1,20 1,40
j 0,57 0,97
k 1,20 1,42
l 6,15 6,25
m 8,49 8,59
n 13,58 14,08
p 4,126 4,130
q 2,898 2,902
s 4,00 5,00
t 2,50 3,00
w 0,20 0,50
a
Resilient electrical contact, slot design optional and meet 4.2.2 requirements.
b
Stainless steel or ceramic beads, not less than 5pcs, radially and uniformly
distributed.

---------------------- Page: 19 ----------------------
SIST EN IEC 61169-61:2020
– 14 – IEC 61169-61:2020 © IEC 2020
4.3.2 Standard test connector with socket centre contact
The mating face of a standard test connector with socket centre contact is shown as Figure 6
and its
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.