SIST EN 301 489-50 V2.1.1:2017

ETSI EN 301 489-50 V2.1.1 (2017-02)






HARMONISED EUROPEAN STANDARD
ElectroMagnetic Compatibility (EMC)
standard for radio equipment and services;
Part 50: Specific conditions for Cellular Communication
Base Station (BS), repeater and ancillary equipment;
Harmonised Standard covering the essential requirements
of article 3.1(b) of Directive 2014/53/EU

---------------------- Page: 1 ----------------------
2 ETSI EN 301 489-50 V2.1.1 (2017-02)



Reference
REN/ERM-EMC-334
Keywords
EMC, GSM, harmonised standard, LTE, MSR,
OFDMA, WCDMA,WMAN
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE

Tel.: +33 4 92 94 42 00  Fax: +33 4 93 65 47 16

Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88

Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the
print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.

© European Telecommunications Standards Institute 2017.
All rights reserved.

TM TM TM
DECT , PLUGTESTS , UMTS and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members.
TM
3GPP and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI

---------------------- Page: 2 ----------------------
3 ETSI EN 301 489-50 V2.1.1 (2017-02)
Contents
Intellectual Property Rights . 5
Foreword . 5
Modal verbs terminology . 5
1 Scope . 6
2 References . 6
2.1 Normative references . 6
2.2 Informative references . 8
3 Definitions and abbreviations . 9
3.1 Definitions . 9
3.2 Abbreviations . 11
4 Test conditions . 12
4.1 General . 12
4.2 Arrangements for test signals . 13
4.2.0 General . 13
4.2.1 Multiple enclosure BS solution . 13
4.2.2 Arrangements for test signals at the input of transmitters . 14
4.2.3 Arrangements for test signals at the output of transmitters . 14
4.2.4 Arrangements for test signals at the input of receivers . 14
4.2.5 Arrangements for test signals at the output of receivers . 14
4.2.6 Arrangements for test signals for repeaters . 14
4.3 Exclusion bands . 14
4.3.1 Transmitter exclusion band . 14
4.3.2 Receiver exclusion band . 14
4.4 Narrow band responses of receivers . 15
4.5 Normal test modulation . 15
4.6 Test configurations for MSR, MC and MB . 16
5 Performance assessment . 17
5.1 General . 17
5.2 Equipment which can provide a continuous communication link . 18
5.2.0 General . 18
5.2.1 Assessment of BLER/Throughput/BER/FER in Downlink . 18
5.2.1.0 General . 18
5.2.1.1 Assessment of BER using static layer 1 functions . 18
5.2.1.2 Assessment of BER using RXQUAL . 19
5.2.2 Assessment of BLER/Throughput/BER/FER in Uplink . 19
5.2.2.0 General . 19
5.2.2.1 Assessment of BER using RXQUAL . 19
5.2.2.2 Assessment of BER using reported BER . 19
5.2.3 Assessment of RF gain variations of repeaters . 19
5.3 Equipment which does not provide a continuous communication link . 20
5.4 Ancillary equipment . 20
5.5 Equipment classification . 20
6 Performance criteria . 20
6.1 Performance criteria for continuous phenomena applied to Base Stations and Repeaters . 20
6.1.1 Base Stations (BS) . 20
6.1.2 Repeaters . 22
6.2 Performance criteria for transient phenomena for Base Station and Repeaters . 22
6.2.1 Base stations (BS) . 22
6.2.2 Repeaters . 22
6.3 Performance criteria for ancillary equipment tested on a standalone basis . 22
6.3.0 General . 22
6.3.1 Performance criteria for continuous phenomena for ancillary equipment . 23
6.3.2 Performance criteria for transient phenomena for ancillary equipment . 23
ETSI

---------------------- Page: 3 ----------------------
4 ETSI EN 301 489-50 V2.1.1 (2017-02)
7 Applicability overview tables . 23
7.1 Emission . 23
7.1.1 General . 23
7.1.2 Special conditions . 23
7.2 Immunity . 23
7.2.1 General . 23
7.2.2 Special conditions . 24
Annex A (informative): Relationship between the present document and the essential
requirements of Directive 2014/53/EU . 25
Annex B (informative): Examples of base station radio equipment for digital cellular radio
telecommunications systems within the scope of the present
document . 27
B.0 General . 27
B.1 Base station equipment for IMT-2000 CDMA Direct Spread (UTRA) . 27
B.2 Base station equipment for Evolved Universal Terrestrial Radio Access (E-UT RA) . 27
B.3 GSM base station, ancillary RF amplifiers, and GSM repeaters meeting Phase 2 and 2+ . 27
B.4 Other types of GSM base station, ancillary RF amplifiers, and GSM repeaters equipment . 28
B.5 Multi Standard Radio (MSR) Base station equipment . 28
B.6 OFDMA WMAN Base station equipment . 28
B.7 OFDMA WMAN Base station equipment . 28
B.8 CDMA 1x spread spectrum Base stations, repeaters and ancillary equipment . 28
Annex C (informative): Bibliography . 30
Annex D (informative): Change history . 31
History . 32


ETSI

---------------------- Page: 4 ----------------------
5 ETSI EN 301 489-50 V2.1.1 (2017-02)
Intellectual Property Rights
IPRs essential or potentially essential to the present document may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (https://ipr.etsi.org/).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Foreword
This Harmonised European Standard (EN) has been produced by ETSI Technical Committee Electromagnetic
compatibility and Radio spectrum Matters (ERM).
The present document has been prepared under the Commission's standardisation request C(2015) 5376 final [i.15] to
provide one voluntary means of conforming to the essential requirements of Directive 2014/53/EU on the harmonisation
of the laws of the Member States relating to the making available on the market of radio equipment and repealing
Directive 1999/5/EC [i.1].
Once the present document is cited in the Official Journal of the European Union under that Directive, compliance with
the normative clauses of the present document given in table A.1 confers, within the limits of the scope of the present
document, a presumption of conformity with the corresponding essential requirements of that Directive, and associated
EFTA regulations.
The present document has been produced to rationalize the current ETSI EN 301 489 series [i.9] of EMC standards by
collating the EMC requirements for Digital Cellular Communication Base Station (BS), repeater and ancillary
Equipment into a single standard, there are no technical changes to product EMC Test requirements. The present
document has been produced to replace ETSI EN 301 489-8 [i.9] (GSM/EDGE), ETSI EN 301 489-23 [i.9] (WCDMA
and LTE, UTRA/E-UTRA), ETSI EN 301 489-26 [i.9] CDMA, 2000 1x and those parts of ETSI EN 301 489-4 [i.9]
which pertain to OFDMA WMAN BS and to incorporate MSR and OFDMA WMAN.
The present document is part 50 of a multi-part deliverable. Full details of the entire series can be found in part [1].

National transposition dates
Date of adoption of this EN: 23 January 2017
Date of latest announcement of this EN (doa): 30 April 2017
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 31 October 2017
Date of withdrawal of any conflicting National Standard (dow): 31 October 2018

Modal verbs terminology
In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and
"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of
provisions).
"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.
ETSI

---------------------- Page: 5 ----------------------
6 ETSI EN 301 489-50 V2.1.1 (2017-02)
1 Scope
The present document specifies technical characteristics and methods of measurements for equipment the following
equipment types:
1) digital cellular base station equipment;
2) repeaters;
3) associated ancillary equipment.
Including individually and combinations of:
• UTRA, WCDMA (IMT-2000 Direct Spread, W-CDMA, UMTS)
• E-UTRA, LTE (IMT-2000 and IMT advanced)
• GSM (IMT-2000 SC, Technology GSM/EDGE)
• MSR (IMT-2000 and IMT advanced, combination of technologies above)
• OFDMA WMAN (IMT-2000 OFDMA, OFDMA WMAN)
• CDMA (CDMA2000 - IMT MC, CDMA2000 1X)
Technical specifications related to the antenna port and emissions from the enclosure port of radio equipment (base
station (BS), and repeaters) are not included in the present document. Such technical specifications are found in the
relevant product standards for the effective use of the radio spectrum.
Examples of base station equipment covered by the present document are given in annex A.
In case of differences (for instance concerning special conditions, definitions, abbreviations) between the present
document and ETSI EN 301 489-1 [1], the provisions of the present document take precedence.
The environmental classification and the emission and immunity requirements used in the present document are as
stated in ETSI EN 301 489-1 [1], except for any special conditions included in the present document.
The present document covers the essential requirements of article 3.1(b) of Directive 2014/53/EU under the conditions
identified in annex A.
Technical specifications related to the antenna port of radio equipment and radiated emissions from the enclosure port
of radio equipment and combinations of radio and associated ancillary equipment are given in the harmonised product
standards ETSI EN 301 908-1 [28] or ETSI EN 301 502 [8] for the effective and efficient use of the radio spectrum.
2 References
2.1 Normative references
References are specific, identified by date of publication and/or edition number or version number. Only the cited
version applies.
Referenced documents which are not found to be publicly available in the expected location might be found at
http://docbox.etsi.org/Reference.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are necessary for the application of the present document.
ETSI

---------------------- Page: 6 ----------------------
7 ETSI EN 301 489-50 V2.1.1 (2017-02)
[1] ETSI EN 301 489-1 (V2.1.1) (02-2017): "ElectroMagnetic Compatibility (EMC) standard for
radio equipment and services; Part 1: Common technical requirements; Harmonised Standard
covering the essential requirements of article 3.1(b) of the Directive 2014/53/EU and the essential
requirements of article 6 of the Directive 2014/30/EU".
[2] ETSI TS 125 141 (V12.6.0) (01-2015): "Universal Mobile Telecommunications System (UMTS);
Base Station (BS) conformance testing (FDD) (3GPP TS 25.141 version 12.6.0 Release 12)".
[3] ETSI TS 125 142 (V12.1.0) (01-2015): "Universal Mobile Telecommunications System (UMTS);
Base Station (BS) conformance testing (TDD) (3GPP TS 25.142 version 12.1.0 Release 12)".
[4] ETSI TS 125 143 (V12.1.0) (01-2015): "Universal Mobile Telecommunications System (UMTS);
UTRA repeater conformance testing (3GPP TS 25.143 version 12.1.0 Release 12)".
[5] ETSI TS 136 104 (V12.8.0) (07-2015): "LTE; Evolved Universal Terrestrial Radio Access
(E-UTRA); Base Station (BS) radio transmission and reception (3GPP TS 36.104 version 12.8.0
Release 12)".
[6] ETSI TS 136 141 (V12.8.0) (07-2015): "LTE; Evolved Universal Terrestrial Radio Access
(E-UTRA); Base Station (BS) conformance testing (3GPP TS 36.141 version 12.8.0 Release 12)".
[7] ETSI TS 145 008 (V12.4.0) (01-2015): "Digital cellular telecommunications system (Phase 2+);
Radio subsystem link control (3GPP TS 45.008 version 12.4.0 Release 12)".
[8] ETSI EN 301 502 (V12.5.1) (07-2016): "Global System for Mobile communications (GSM); Base
Station (BS) equipment; Harmonised Standard covering the essential requirements of article 3.2 of
the Directive 2014/53/EU".
[9] ETSI TS 151 021 (V12.3.0) (01-2015): "Digital cellular telecommunications system (Phase 2+);
Base Station System (BSS) equipment specification; Radio aspects (3GPP TS 51.021
version 12.3.0 Release 12)".
[10] Void.
[11] ETSI TS 137 104 (V12.8.0) (07-2015): "Digital cellular telecommunications system (Phase 2+);
Universal Mobile Telecommunications System (UMTS); LTE; E-UTRA, UTRA and GSM/EDGE;
Multi-Standard Radio (MSR) Base Station (BS) radio transmission and reception (3GPP
TS 37.104 version 12.8.0 Release 12)".
[12] ETSI TS 137 141 (V12.8.0) (07-2015): "Digital cellular telecommunications system (Phase 2+);
Universal Mobile Telecommunications System (UMTS); LTE; E-UTRA, UTRA and GSM/EDGE;
Multi-Standard Radio (MSR) Base Station (BS) conformance testing (3GPP TS 37.141
version 12.8.0 Release 12)".
[13] ETSI EN 301 908-5 (V5.2.1) (09-2011): "IMT cellular networks; Harmonized EN covering the
essential requirements of article 3.2 of the R&TTE Directive; Part 5: CDMA Multi-Carrier
(cdma2000) Base Stations (BS)".
[14] ETSI EN 301 908-7 (V4.2.1) (03-2010): "Electromagnetic compatibility and Radio spectrum
Matters (ERM); Base Stations (BS), Repeaters and User Equipment (UE) for IMT-2000 Third-
Generation cellular networks; Part 7: Harmonized EN for IMT-2000, CDMA TDD (UTRA TDD
and E-UTRA TDD) (BS) covering the essential requirements of article 3.2 of the R&TTE
Directive".
[15] ETSI EN 301 908-20 (V6.3.1) (05-2016): "IMT cellular networks; Harmonised Standard covering
the essential requirements of article 3.2 of the Directive 2014/53/EU; Part 20: OFDMA TDD
TM
WMAN (Mobile WiMAX ) TDD Base Stations (BS)".
[16] ETSI EN 301 908-22 (V6.1.1) (07-2016): "IMT cellular networks; Harmonised Standard covering
the essential requirements of article 3.2 of the Directive 2014/53/EU; Part 22: OFDMA TDD
TM
WMAN (Mobile WiMAX ) FDD Base Stations (BS)".
[17] ETSI EN 302 544-1 (V1.1.2) (01-2010): "Broadband Data Transmission Systems operating in the
2 500 MHz to 2 690 MHz frequency band; Part 1: TDD Base Stations; Harmonized EN covering
the essential requirements of article 3.2 of the R&TTE Directive".
ETSI

---------------------- Page: 7 ----------------------
8 ETSI EN 301 489-50 V2.1.1 (2017-02)
[18] TIA-97 (2014): "Recommended Minimum Performance Standard for cdma2000 Spread Spectrum
Base Stations".
[19] TIA-2000 Series, Revision F: "Introduction to CDMA2000 spread spectrum systems **Includes
TIA-2000.1 (2013), TIA-2000.2 (2014), TIA-2000.3 (2014), TIA-2000.4 (2014), and TIA-2000.5
(2014)**".
[20] ETSI EN 301 449 (V1.1.1) (07-2006): "Electromagnetic compatibility and Radio spectrum
Matters (ERM); Harmonized EN for CDMA spread spectrum base stations operating in the
450 MHz cellular band (CDMA 450) and 410, 450 and 870 MHz PAMR bands (CDMA-PAMR)
covering essential requirements of article 3.2 of the R&TTE Directive".
[21] ETSI EN 302 426 (V1.1.1) (09-2006): "Electromagnetic compatibility and Radio spectrum
Matters (ERM); Harmonized EN for CDMA spread spectrum Repeaters operating in the 450 MHz
cellular band (CDMA450) and the 410 MHz, 450 MHz and 870 MHz PAMR bands (CDMA-
PAMR) covering essential requirements of article 3.2 of the R&TTE Directive".
[22] ETSI TS 125 101 (V12.8.0) (07-2015): "Universal Mobile Telecommunications System (UMTS);
User Equipment (UE) radio transmission and reception (FDD) (3GPP TS 25.101 version 12.8.0
Release 12)".
[23] ETSI TS 125 102 (V12.0.0) (10-2014): "Universal Mobile Telecommunications System (UMTS);
User Equipment (UE) radio transmission and reception (TDD) (3GPP TS 25.102 version 12.0.0
Release 12)".
[24] ETSI TS 136 101 (V12.8.0) (09-2015): "LTE; Evolved Universal Terrestrial Radio Access
(E-UTRA); User Equipment (UE) radio transmission and reception (3GPP TS 36.101 version
12.8.0 Release 12)".
[25] ETSI TS 136 143 (V12.1.0) (02-2015): "LTE; Evolved Universal Terrestrial Radio Access
(E-UTRA); FDD repeater conformance testing (3GPP TS 36.143 version 12.1.0 Release 12)".
[26] ETSI TS 151 010-1 (V12.4.0) (06-2015): "Digital cellular telecommunications system (Phase 2+);
Mobile Station (MS) conformance specification; Part 1: Conformance specification
(3GPP TS 51.010-1 version 12.4.0 Release 12)".
[27] ETSI TS 137 113 (V12.3.0) (02-2015): "Digital cellular telecommunications system (Phase 2+);
Universal Mobile Telecommunications System (UMTS); LTE; E-UTRA, UTRA and GSM/EDGE;
Multi-Standard Radio (MSR) Base Station (BS) Electromagnetic Compatibility (EMC)
(3GPP TS 37.113 version 12.3.0 Release 12)".
[28] ETSI EN 301 908-1 (V11.1.1) (07-2016): "IMT cellular networks; Harmonised Standard covering
the essential requirements of article 3.2 of the Directive 2014/53/EU; Part 1: Introduction and
common requirements".
2.2 Informative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are not necessary for the application of the present document but they assist the
user with regard to a particular subject area.
[i.1] Directive 2014/53/EU of the European Parliament and of the Council of 16 April 2014 on the
harmonisation of the laws of the Member States relating to the making available on the market of
radio equipment and repealing Directive 1999/5/EC.
[i.2] Void.
ETSI

---------------------- Page: 8 ----------------------
9 ETSI EN 301 489-50 V2.1.1 (2017-02)
[i.3] ETSI TS 125 104: "Universal Mobile Telecommunications System (UMTS); Base Station (BS)
radio transmission and reception (FDD) (3GPP TS 25.104)".
[i.4] ETSI TS 125 105: "Universal Mobile Telecommunications System (UMTS); Base Station (BS)
radio transmission and reception (TDD) (3GPP TS 25.105)".
[i.5] ETSI TS 125 106: "Universal Mobile Telecommunications System (UMTS); UTRA repeater radio
transmission and reception (3GPP TS 25.106)".
[i.6] ETSI TS 136 106: "LTE; Evolved Universal Terrestrial Radio Access (E-UTRA); FDD repeater
radio transmission and reception (3GPP TS 36.106)".
[i.7] Void.
[i.8] Void.
[i.9] ETSI EN 301 489 (all parts): "ElectroMagnetic Compatibility (EMC) standard for radio equipment
and services".
[i.10] Void.
[i.11] Void.
[i.12] Void.
[i.13] Void.
[i.14] Recommendation ITU-R SM.329-12: "Unwanted emissions in the spurious domain".
[i.15] Commission Implementing Decision C(2015) 5376 final of 4.8.2015 on a standardisation request
to the European Committee for Electrotechnical Standardisation and to the European
Telecommunications Standards Institute as regards radio equipment in support of Directive
2014/53/EU of the European Parliament and of the Council.
3 Definitions and abbreviations
3.1 Definitions
For the purposes of the present document, the terms and definitions given in ETSI EN 301 489-1 [1] and the following
apply:
abis interface: logical interface between a BTS and a BSC
bearer: information transmission path of defined characteristics for transfer of user data or predefined test data
CDMA 1x Spread Spectrum: wireless air interface standard for spread-spectrum technology with a spreading rate 1
CDMA-PAMR: Public Access Mobile Radio system based on TIA-2000 [19] Spreading Rate 1 specifications
channel bandwidth: RF bandwidth supporting a single E-UTRA RF carrier with the transmission bandwidth
configured in the uplink or downlink of a cell
NOTE: The channel bandwidth is measured in MHz and is used as a reference for transmitter and receiver RF
requirements.
forward CDMA channel: CDMA channel from a base station to mobile stations
NOTE: The forward CDMA channel contains one or more code channels that are transmitted on a CDMA
frequency assignment using a particular pilot PN offset.
International Mobile T
...

Final draft ETSI EN 301 489-50 V2.1.1 (2016-11)






HARMONISED EUROPEAN STANDARD
ElectroMagnetic Compatibility (EMC)
standard for radio equipment and services;
Part 50: Specific conditions for Cellular Communication
Base Station (BS), repeater and ancillary equipment;
Harmonised Standard covering the essential requirements
of article 3.1(b) of Directive 2014/53/EU

---------------------- Page: 1 ----------------------
2 Final draft ETSI EN 301 489-50 V2.1.1 (2016-11)



Reference
REN/ERM-EMC-334
Keywords
EMC, GSM, harmonised standard, LTE, MSR,
OFDMA, WCDMA,WMAN
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE

Tel.: +33 4 92 94 42 00  Fax: +33 4 93 65 47 16

Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88

Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the
print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.

© European Telecommunications Standards Institute 2016.
All rights reserved.

TM TM TM
DECT , PLUGTESTS , UMTS and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members.
TM
3GPP and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI

---------------------- Page: 2 ----------------------
3 Final draft ETSI EN 301 489-50 V2.1.1 (2016-11)
Contents
Intellectual Property Rights . 5
Foreword . 5
Modal verbs terminology . 5
1 Scope . 6
2 References . 6
2.1 Normative references . 6
2.2 Informative references . 8
3 Definitions and abbreviations . 9
3.1 Definitions . 9
3.2 Abbreviations . 11
4 Test conditions . 12
4.1 General . 12
4.2 Arrangements for test signals . 13
4.2.0 General . 13
4.2.1 Multiple enclosure BS solution . 13
4.2.2 Arrangements for test signals at the input of transmitters . 14
4.2.3 Arrangements for test signals at the output of transmitters . 14
4.2.4 Arrangements for test signals at the input of receivers . 14
4.2.5 Arrangements for test signals at the output of receivers . 14
4.2.6 Arrangements for test signals for repeaters . 14
4.3 Exclusion bands . 14
4.3.1 Transmitter exclusion band . 14
4.3.2 Receiver exclusion band . 14
4.4 Narrow band responses of receivers . 15
4.5 Normal test modulation . 15
4.6 Test configurations for MSR, MC and MB . 16
5 Performance assessment . 18
5.1 General . 18
5.2 Equipment which can provide a continuous communication link . 18
5.2.0 General . 18
5.2.1 Assessment of BLER/Throughput/BER/FER in Downlink . 18
5.2.1.0 General . 18
5.2.1.1 Assessment of BER using static layer 1 functions . 19
5.2.1.2 Assessment of BER using RXQUAL . 19
5.2.2 Assessment of BLER/Throughput/BER/FER in Uplink . 19
5.2.2.0 General . 19
5.2.2.1 Assessment of BER using RXQUAL . 19
5.2.2.2 Assessment of BER using reported BER . 19
5.2.3 Assessment of RF gain variations of repeaters . 20
5.3 Equipment which does not provide a continuous communication link . 20
5.4 Ancillary equipment . 20
5.5 Equipment classification . 20
6 Performance criteria . 20
6.1 Performance criteria for continuous phenomena applied to Base Stations and Repeaters . 20
6.1.1 Base Stations (BS) . 20
6.1.2 Repeaters . 22
6.2 Performance criteria for transient phenomena for Base Station and Repeaters . 22
6.2.1 Base stations (BS) . 22
6.2.2 Repeaters . 22
6.3 Performance criteria for ancillary equipment tested on a standalone basis . 22
6.3.0 General . 22
6.3.1 Performance criteria for continuous phenomena for ancillary equipment . 23
6.3.2 Performance criteria for transient phenomena for ancillary equipment . 23
ETSI

---------------------- Page: 3 ----------------------
4 Final draft ETSI EN 301 489-50 V2.1.1 (2016-11)
7 Applicability overview tables . 23
7.1 Emission . 23
7.1.1 General . 23
7.1.2 Special conditions . 23
7.2 Immunity . 23
7.2.1 General . 23
7.2.2 Special conditions . 24
Annex A (informative): Relationship between the present document and the essential
requirements of Directive 2014/53/EU . 25
Annex B (informative): Examples of base station radio equipment for digital cellular radio
telecommunications systems within the scope of the present
document . 27
B.0 General . 27
B.1 Base station equipment for IMT-2000 CDMA Direct Spread (UTRA) . 27
B.2 Base station equipment for Evolved Universal Terrestrial Radio Access (E-UT RA) . 27
B.3 GSM base station, ancillary RF amplifiers, and GSM repeaters meeting Phase 2 and 2+ . 27
B.4 Other types of GSM base station, ancillary RF amplifiers, and GSM repeaters equipment . 28
B.5 Multi Standard Radio (MSR) Base station equipment . 28
B.6 OFDMA WMAN Base station equipment . 28
B.7 OFDMA WMAN Base station equipment . 28
B.8 CDMA 1x spread spectrum Base stations, repeaters and ancillary equipment . 28
Annex C (informative): Bibliography . 30
Annex D (informative): Change history . 31
History . 32


ETSI

---------------------- Page: 4 ----------------------
5 Final draft ETSI EN 301 489-50 V2.1.1 (2016-11)
Intellectual Property Rights
IPRs essential or potentially essential to the present document may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (https://ipr.etsi.org/).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Foreword
This final draft Harmonised European Standard (EN) has been produced by ETSI Technical Committee
Electromagnetic compatibility and Radio spectrum Matters (ERM), and is now submitted for the Vote phase of the
ETSI standards EN Approval Procedure.
The present document has been prepared under the Commission's standardisation request C(2015) 5376 final [i.15] to
provide one voluntary means of conforming to the essential requirements of Directive 2014/53/EU on the harmonisation
of the laws of the Member States relating to the making available on the market of radio equipment and repealing
Directive 1999/5/EC [i.1].
Once the present document is cited in the Official Journal of the European Union under that Directive, compliance with
the normative clauses of the present document given in table A.1 confers, within the limits of the scope of the present
document, a presumption of conformity with the corresponding essential requirements of that Directive, and associated
EFTA regulations.
The present document has been produced to rationalize the current ETSI EN 301 489 series [i.9] of EMC standards by
collating the EMC requirements for Digital Cellular Communication Base Station (BS), repeater and ancillary
Equipment into a single standard, there are no technical changes to product EMC Test requirements. The present
document has been produced to replace ETSI EN 301 489-8 [i.9] (GSM/EDGE), ETSI EN 301 489-23 [i.9] (WCDMA
and LTE, UTRA/E-UTRA), ETSI EN 301 489-26 [i.9] CDMA, 2000 1x and those parts of ETSI EN 301 489-4 [i.9]
which pertain to OFDMA WMAN BS and to incorporate MSR and OFDMA WMAN.
The present document is part 50 of a multi-part deliverable. Full details of the entire series can be found in part [1].

Proposed national transposition dates
Date of latest announcement of this EN (doa): 3 months after ETSI publication
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 6 months after doa
Date of withdrawal of any conflicting National Standard (dow): 18 months after doa

Modal verbs terminology
In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and
"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of
provisions).
"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.
ETSI

---------------------- Page: 5 ----------------------
6 Final draft ETSI EN 301 489-50 V2.1.1 (2016-11)
1 Scope
The present document specifies technical characteristics and methods of measurements for equipment the following
equipment types:
1) digital cellular base station equipment;
2) repeaters;
3) associated ancillary equipment.
Including individually and combinations of:
• UTRA, WCDMA (IMT-2000 Direct Spread, W-CDMA, UMTS)
• E-UTRA, LTE (IMT-2000 and IMT advanced)
• GSM (IMT-2000 SC, Technology GSM/EDGE)
• MSR (IMT-2000 and IMT advanced, combination of technologies above)
• OFDMA WMAN (IMT-2000 OFDMA, OFDMA WMAN)
• CDMA (CDMA2000 – IMT MC, CDMA2000 1X)
Technical specifications related to the antenna port and emissions from the enclosure port of radio equipment (base
station (BS), and repeaters) are not included in the present document. Such technical specifications are found in the
relevant product standards for the effective use of the radio spectrum.
Examples of base station equipment covered by the present document are given in annex A.
In case of differences (for instance concerning special conditions, definitions, abbreviations) between the present
document and ETSI EN 301 489-1 [1], the provisions of the present document take precedence.
The environmental classification and the emission and immunity requirements used in the present document are as
stated in ETSI EN 301 489-1 [1], except for any special conditions included in the present document.
The present document covers the essential requirements of article 3.1(b) of Directive 2014/53/EU under the conditions
identified in annex A.
Technical specifications related to the antenna port of radio equipment and radiated emissions from the enclosure port
of radio equipment and combinations of radio and associated ancillary equipment are given in the harmonised product
standards ETSI EN 301 908-1 [28] or ETSI EN 301 502 [8] for the effective and efficient use of the radio spectrum.
2 References
2.1 Normative references
References are specific, identified by date of publication and/or edition number or version number. Only the cited
version applies.
ETSI

---------------------- Page: 6 ----------------------
7 Final draft ETSI EN 301 489-50 V2.1.1 (2016-11)
Referenced documents which are not found to be publicly available in the expected location might be found at
http://docbox.etsi.org/Reference.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are necessary for the application of the present document.
[1] ETSI EN 301 489-1 (V2.1.1) (11-2016): "ElectroMagnetic Compatibility (EMC) standard for
radio equipment and services; Harmonised Standard covering the essential requirements of article
3.1(b) of the Directive 2014/53/EU and the essential requirements of article 6 of the Directive
2014/30/EU; Part 1: Common technical requirements".
[2] ETSI TS 125 141 (V12.6.0) (01-2015): "Universal Mobile Telecommunications System (UMTS);
Base Station (BS) conformance testing (FDD) (3GPP TS 25.141 version 12.6.0 Release 12)".
[3] ETSI TS 125 142 (V12.1.0) (01-2015): "Universal Mobile Telecommunications System (UMTS);
Base Station (BS) conformance testing (TDD) (3GPP TS 25.142 version 12.1.0 Release 12)".
[4] ETSI TS 125 143 (V12.1.0) (01-2015): "Universal Mobile Telecommunications System (UMTS);
UTRA repeater conformance testing (3GPP TS 25.143 version 12.1.0 Release 12)".
[5] ETSI TS 136 104 (V12.8.0) (07-2015): "LTE; Evolved Universal Terrestrial Radio Access
(E-UTRA); Base Station (BS) radio transmission and reception (3GPP TS 36.104 version 12.8.0
Release 12)".
[6] ETSI TS 136 141 (V12.8.0) (07-2015): "LTE; Evolved Universal Terrestrial Radio Access
(E-UTRA); Base Station (BS) conformance testing (3GPP TS 36.141 version 12.8.0 Release 12)".
[7] ETSI TS 145 008 (V12.4.0) (01-2015): "Digital cellular telecommunications system (Phase 2+);
Radio subsystem link control (3GPP TS 45.008 version 12.4.0 Release 12)".
[8] ETSI EN 301 502 (V12.1.6) (01-2016): "Global System for Mobile communications (GSM); Base
Station (BS) equipment; Harmonised Standard covering the essential requirements of article 3.2 of
the Directive 2014/53/EU".
[9] ETSI TS 151 021 (V12.3.0) (01-2015): "Digital cellular telecommunications system (Phase 2+);
Base Station System (BSS) equipment specification; Radio aspects (3GPP TS 51.021
version 12.3.0 Release 12)".
[10] Void.
[11] ETSI TS 137 104 (V12.8.0) (07-2015): "Digital cellular telecommunications system (Phase 2+);
Universal Mobile Telecommunications System (UMTS); LTE; E-UTRA, UTRA and GSM/EDGE;
Multi-Standard Radio (MSR) Base Station (BS) radio transmission and reception (3GPP
TS 37.104 version 12.8.0 Release 12)".
[12] ETSI TS 137 141 (V12.8.0): "Digital cellular telecommunications system (Phase 2+); Universal
Mobile Telecommunications System (UMTS); LTE; E-UTRA, UTRA and GSM/EDGE; Multi-
Standard Radio (MSR) Base Station (BS) conformance testing (3GPP TS 37.141 version 12.8.0
Release 12)".
[13] ETSI EN 301 908-5 (V5.2.1) (09-2011): "IMT cellular networks; Harmonized EN covering the
essential requirements of article 3.2 of the R&TTE Directive; Part 5: CDMA Multi-Carrier
(cdma2000) Base Stations (BS)".
[14] ETSI EN 301 908-7 (V4.2.1) (03-2010): "Electromagnetic compatibility and Radio spectrum
Matters (ERM); Base Stations (BS), Repeaters and User Equipment (UE) for IMT-2000 Third-
Generation cellular networks; Part 7: Harmonized EN for IMT-2000, CDMA TDD (UTRA TDD
and E-UTRA TDD) (BS) covering the essential requirements of article 3.2 of the R&TTE
Directive".
[15] ETSI EN 301 908-20 (V6.3.1) (05-2016): "IMT cellular networks; Harmonised Standard covering
the essential requirements of article 3.2 of the Directive 2014/53/EU; Part 20: OFDMA TDD
TM
WMAN (Mobile WiMAX ) TDD Base Stations (BS)".
ETSI

---------------------- Page: 7 ----------------------
8 Final draft ETSI EN 301 489-50 V2.1.1 (2016-11)
[16] ETSI EN 301 908-22 (V6.1.0) (05-2016): "IMT cellular networks; Harmonised Standard covering
the essential requirements of article 3.2 of the Directive 2014/53/EU; Part 22: OFDMA TDD
TM
WMAN (Mobile WiMAX ) FDD Base Stations (BS)".
[17] ETSI EN 302 544-1 (V1.1.2) (01-2010): "Broadband Data Transmission Systems operating in the
2 500 MHz to 2 690 MHz frequency band; Part 1: TDD Base Stations; Harmonized EN covering
the essential requirements of article 3.2 of the R&TTE Directive".
[18] TIA-97 (2014): "Recommended Minimum Performance Standard for cdma2000 Spread Spectrum
Base Stations".
[19] TIA-2000 Series, Revision F: "Introduction to CDMA2000 spread spectrum systems **Includes
TIA-2000.1 (2013), TIA-2000.2 (2014), TIA-2000.3 (2014), TIA-2000.4 (2014), and TIA-2000.5
(2014)**".
[20] ETSI EN 301 449 (V1.1.1) (07-2006): "Electromagnetic compatibility and Radio spectrum
Matters (ERM); Harmonized EN for CDMA spread spectrum base stations operating in the
450 MHz cellular band (CDMA 450) and 410, 450 and 870 MHz PAMR bands (CDMA-PAMR)
covering essential requirements of article 3.2 of the R&TTE Directive".
[21] ETSI EN 302 426 (V1.1.1) (09-2006): "Electromagnetic compatibility and Radio spectrum
Matters (ERM); Harmonized EN for CDMA spread spectrum Repeaters operating in the 450 MHz
cellular band (CDMA450) and the 410 MHz, 450 MHz and 870 MHz PAMR bands (CDMA-
PAMR) covering essential requirements of article 3.2 of the R&TTE Directive".
[22] ETSI TS 125 101 (V12.8.0) (07-2015): "Universal Mobile Telecommunications System (UMTS);
User Equipment (UE) radio transmission and reception (FDD) (3GPP TS 25.101 version 12.8.0
Release 12)".
[23] ETSI TS 125 102 (V12.0.0) (10-2014): "Universal Mobile Telecommunications System (UMTS);
User Equipment (UE) radio transmission and reception (TDD) (3GPP TS 25.102 version 12.0.0
Release 12)".
[24] ETSI TS 136 101 (V12.8.0) (09-2015): "LTE; Evolved Universal Terrestrial Radio Access
(E-UTRA); User Equipment (UE) radio transmission and reception (3GPP TS 36.101 version
12.8.0 Release 12)".
[25] ETSI TS 136 143 (V12.1.0) (02-2015): "LTE; Evolved Universal Terrestrial Radio Access
(E-UTRA); FDD repeater conformance testing (3GPP TS 36.143 version 12.1.0 Release 12)".
[26] ETSI TS 151 010-1 (V12.4.0) (06-2015): "Digital cellular telecommunications system (Phase 2+);
Mobile Station (MS) conformance specification; Part 1: Conformance specification (3GPP TS
51.010-1 version 12.4.0 Release 12)".
[27] ETSI TS 137 113 (V12.3.0) (02-2015): "Digital cellular telecommunications system (Phase 2+);
Universal Mobile Telecommunications System (UMTS); LTE; E-UTRA, UTRA and GSM/EDGE;
Multi-Standard Radio (MSR) Base Station (BS) Electromagnetic Compatibility (EMC) (3GPP
TS 37.113 version 12.3.0 Release 12)".
[28] ETSI EN 301 908-1 (V11.0.1) (01-2016): "IMT cellular networks; Harmonised Standard covering
the essential requirements of article 3.2 of the Directive 2014/53/EU; Part 1: Introduction and
common requirements".
2.2 Informative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
ETSI

---------------------- Page: 8 ----------------------
9 Final draft ETSI EN 301 489-50 V2.1.1 (2016-11)
The following referenced documents are not necessary for the application of the present document but they assist the
user with regard to a particular subject area.
[i.1] Directive 2014/53/EU of the European Parliament and of the Council of 16 April 2014 on the
harmonisation of the laws of the Member States relating to the making available on the market of
radio equipment and repealing Directive 1999/5/EC.
[i.2] Void.
[i.3] ETSI TS 125 104: "Universal Mobile Telecommunications System (UMTS); Base Station (BS)
radio transmission and reception (FDD) (3GPP TS 25.104)".
[i.4] ETSI TS 125 105: "Universal Mobile Telecommunications System (UMTS); Base Station (BS)
radio transmission and reception (TDD) (3GPP TS 25.105)".
[i.5] ETSI TS 125 106: "Universal Mobile Telecommunications System (UMTS); UTRA repeater radio
transmission and reception (3GPP TS 25.106)".
[i.6] ETSI TS 136 106: "LTE; Evolved Universal Terrestrial Radio Access (E-UTRA); FDD repeater
radio transmission and reception (3GPP TS 36.106)".
[i.7] Void.
[i.8] Void.
[i.9] ETSI EN 301 489 (all parts): "ElectroMagnetic Compatibility (EMC) standard for radio equipment
and services".
[i.10] Void.
[i.11] Void.
[i.12] Void.
[i.13] Void.
[i.14] Recommendation ITU-R SM.329-12: "Unwanted emissions in the spurious domain".
[i.15] Commission Implementing Decision C(2015) 5376 final of 4.8.2015 on a standardisation request
to the European Committee for Electrotechnical Standardisation and to the European
Telecommunications Standards Institute as regards radio equipment in support of Directive
2014/53/EU of the European Parliament and of the Council.
3 Definitions and abbreviations
3.1 Definitions
For the purposes of the present document, the terms and definitions given in ETSI EN 301 489-1 [1] and the following
apply:
abis interface: logical interface between a BTS and a BSC
bearer: information transmission path of defined characteristics for transfer of user data or predefined test data
CDMA 1x Spread Spectrum: wireless air interface standard for spread-spectrum technology with a spreading rate 1
CDMA-PAMR: Public Access Mobile Radio system based on TIA-2000 [19] Spreading Rate 1 specifications
channel bandwidth: RF bandwidth supporting a single E-UTRA RF carrier with the transmission bandwidth
configured in the uplink or downlink of a cell
NOTE: The channel bandwidth is measured in MHz and is used as a reference for transmitter and receiver RF
requirements.
ETSI

---------------------- Page: 9 -----------
...

Draft ETSI EN 301 489-50 V2.1.0 (2016-06)






HARMONISED EUROPEAN STANDARD
ElectroMagnetic Compatibility (EMC)
standard for radio equipment and services;
Part 50: Specific conditions for Cellular Communication
Base Station (BS), repeater and ancillary equipment;
Harmonised Standard covering the essential requirements
of article 3.1(b) of the Directive 2014/53/EU

---------------------- Page: 1 ----------------------
2 Draft ETSI EN 301 489-50 V2.1.0 (2016-06)



Reference
REN/ERM-EMC-334
Keywords
EMC, GSM, harmonised standard, LTE, MSR,
OFDMA, WCDMA,WMAN
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE

Tel.: +33 4 92 94 42 00  Fax: +33 4 93 65 47 16

Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88

Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the
print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.

© European Telecommunications Standards Institute 2016.
All rights reserved.

TM TM TM
DECT , PLUGTESTS , UMTS and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members.
TM
3GPP and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI

---------------------- Page: 2 ----------------------
3 Draft ETSI EN 301 489-50 V2.1.0 (2016-06)
Contents
Intellectual Property Rights . 5
Foreword . 5
Modal verbs terminology . 5
1 Scope . 6
2 References . 7
2.1 Normative references . 7
2.2 Informative references . 9
3 Definitions and abbreviations . 9
3.1 Definitions . 9
3.2 Abbreviations . 11
4 Test conditions . 12
4.1 General . 12
4.2 Arrangements for test signals . 13
4.2.0 General . 13
4.2.1 Multiple enclosure BS solution . 14
4.2.2 Arrangements for test signals at the input of transmitters . 14
4.2.3 Arrangements for test signals at the output of transmitters . 14
4.2.4 Arrangements for test signals at the input of receivers . 14
4.2.5 Arrangements for test signals at the output of receivers . 14
4.2.6 Arrangements for test signals for repeaters . 14
4.3 Exclusion bands . 15
4.3.1 Transmitter exclusion band . 15
4.3.2 Receiver exclusion band . 15
4.4 Narrow band responses of receivers . 15
4.5 Normal test modulation . 16
4.6 Test configurations for MSR, MC and MB . 17
5 Performance assessment . 18
5.1 General . 18
5.2 Equipment which can provide a continuous communication link . 18
5.2.0 General . 18
5.2.1 Assessment of BLER/Throughput/BER/FER in Downlink . 18
5.2.1.0 General . 18
5.2.1.1 Assessment of BER using static layer 1 functions . 19
5.2.1.2 Assessment of BER using RXQUAL . 19
5.2.2 Assessment of BLER/Throughput/BER/FER in Uplink . 19
5.2.2.0 General . 19
5.2.2.1 Assessment of BER using RXQUAL . 20
5.2.2.2 Assessment of BER using reported BER . 20
5.2.3 Assessment of RF gain variations of repeaters . 20
5.3 Equipment which does not provide a continuous communication link . 20
5.4 Ancillary equipment . 20
5.5 Equipment classification . 20
6 Performance criteria . 20
6.1 Performance criteria for continuous phenomena applied to Base Stations and Repeaters . 20
6.1.1 Base Stations (BS) . 20
6.1.2 Repeaters . 22
6.2 Performance criteria for transient phenomena for Base Station and Repeaters . 22
6.2.1 Base stations (BS) . 22
6.2.2 Repeaters . 23
6.3 Performance criteria for ancillary equipment tested on a standalone basis . 23
6.3.0 General . 23
6.3.1 Performance criteria for continuous phenomena for ancillary equipment . 23
6.3.2 Performance criteria for transient phenomena for ancillary equipment . 23
ETSI

---------------------- Page: 3 ----------------------
4 Draft ETSI EN 301 489-50 V2.1.0 (2016-06)
7 Applicability overview tables . 23
7.1 Emission . 23
7.1.1 General . 23
7.1.2 Special conditions . 24
7.2 Immunity . 24
7.2.1 General . 24
7.2.2 Special conditions . 25
Annex A (normative): Relationship between the present document and the essential
requirements of Directive 2014/53/EU . 26
Annex B (informative): Examples of base station radio equipment for digital cellular radio
telecommunications systems within the scope of the present
document . 28
B.0 General . 28
B.1 Base station equipment for IMT-2000 CDMA Direct Spread (UTRA) . 28
B.2 Base station equipment for Evolved Universal Terrestrial Radio Access (E-UT RA) . 28
B.3 GSM base station, ancillary RF amplifiers, and GSM repeaters meeting Phase 2 and 2+ . 28
B.4 Other types of GSM base station, ancillary RF amplifiers, and GSM repeaters equipment . 29
B.5 Multi Standard Radio (MSR) Base station equipment . 29
B.6 OFDMA WMAN Base station equipment . 29
B.7 OFDMA WMAN Base station equipment . 29
B.8 CDMA 1x spread spectrum Base stations, repeaters and ancillary equipment . 29
Annex C (informative): Bibliography . 31
Annex D (informative): Change History . 32
History . 33


ETSI

---------------------- Page: 4 ----------------------
5 Draft ETSI EN 301 489-50 V2.1.0 (2016-06)
Intellectual Property Rights
IPRs essential or potentially essential to the present document may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (https://ipr.etsi.org/).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Foreword
This draft Harmonised European Standard (EN) has been produced by ETSI Technical Committee Electromagnetic
compatibility and Radio spectrum Matters (ERM), and is now submitted for the combined Public Enquiry and Vote
phase of the ETSI standards EN Approval Procedure.
The present document has been prepared under the Commission's standardisation request C(2015) 5376 final [i.15] to
provide one voluntary means of conforming to the essential requirements of Directive 2014/53/EU on the harmonisation
of the laws of the Member States relating to the making available on the market of radio equipment and repealing
Directive 1999/5/EC [i.1].
Once the present document is cited in the Official Journal of the European Union under that Directive, compliance with
the normative clauses of the present document given in table A.1 confers, within the limits of the scope of the present
document, a presumption of conformity with the corresponding essential requirements of that Directive, and associated
EFTA regulations.
The present document has been produced to rationalize the current ETSI EN 301 489 series [i.9] of EMC standards by
collating the EMC requirements for Digital Cellular Communication Base Station (BS), repeater and ancillary
Equipment into a single standard, there are no technical changes to product EMC Test requirements. The present
document has been produced to replace ETSI EN 301 489-8 [i.9] (GSM/EDGE), ETSI EN 301 489-23 [i.9] (WCDMA
and LTE, UTRA/E-UTRA), ETSI EN 301 489-26 [i.9] CDMA, 2000 1x and those parts of ETSI EN 301 489-4 [i.9]
which pertain to OFDMA WMAN BS and to incorporate MSR and OFDMA WMAN.
The present document is part 50 of a multi-part deliverable. Full details of the entire series can be found in part [1].

Proposed national transposition dates
Date of latest announcement of this EN (doa): 3 months after ETSI publication
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 6 months after doa
Date of withdrawal of any conflicting National Standard (dow): 18 months after doa

Modal verbs terminology
In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and
"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of
provisions).
"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.
ETSI

---------------------- Page: 5 ----------------------
6 Draft ETSI EN 301 489-50 V2.1.0 (2016-06)
1 Scope
The present document applies to the following equipment types:
1) digital cellular base station equipment;
2) repeaters;
3) associated ancillary equipment.
Including individually and combinations of:
• UTRA, WCDMA (IMT-2000 Direct Spread, W-CDMA, UMTS)
• E-UTRA, LTE (IMT-2000 and IMT advanced)
• GSM (IMT-2000 SC, Technology GSM/EDGE)
• MSR (IMT-2000 and IMT advanced, combination of technologies above)
• OFDMA WMAN (IMT-2000 OFDMA, OFDMA WMAN)
• CDMA (CDMA2000 – IMT MC, CDMA2000 1X)
Technical specifications related to the antenna port and emissions from the enclosure port of radio equipment (base
station (BS), and repeaters) are not included in the present document. Such technical specifications are found in the
relevant product standards for the effective use of the radio spectrum.
Examples of base station equipment covered by the present document are given in annex A.
In case of differences (for instance concerning special conditions, definitions, abbreviations) between the present
document and ETSI EN 301 489-1 [1], the provisions of the present document take precedence.
The environmental classification and the emission and immunity requirements used in the present document are as
stated in ETSI EN 301 489-1 [1], except for any special conditions included in the present document.
The present document, together with ETSI EN 301 489-1 [1], contains requirements to demonstrate that above named
equipment both effectively uses and supports the efficient use of radio spectrum in order to avoid harmful interference.
Technical specifications related to the antenna port of radio equipment and radiated emissions from the enclosure port
of radio equipment and combinations of radio and associated ancillary equipment are given in the harmonized product
standards ETSI EN 301 908-1 [28] or ETSI EN 301 502 [8] for the effective use of the radio spectrum.
ETSI

---------------------- Page: 6 ----------------------
7 Draft ETSI EN 301 489-50 V2.1.0 (2016-06)
2 References
2.1 Normative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
Referenced documents which are not found to be publicly available in the expected location might be found at
http://docbox.etsi.org/Reference.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are necessary for the application of the present document.
[1] ETSI EN 301 489-1 (V2.1.0) (04-2016): "ElectroMagnetic Compatibility (EMC) standard for
radio equipment and services; Harmonised Standard covering the essential requirements of
article 3.1(b) of the Directive 2014/53/EU and the essential requirements of article 6 of the
Directive 2014/30/EU; Part 1: Common technical requirements".
[2] ETSI TS 125 141 (V12.6.0) (01-2015): "Universal Mobile Telecommunications System (UMTS);
Base Station (BS) conformance testing (FDD) (3GPP TS 25.141 version 12.6.0 Release 12)".
[3] ETSI TS 125 142 (V12.1.0) (01-2015): "Universal Mobile Telecommunications System (UMTS);
Base Station (BS) conformance testing (TDD) (3GPP TS 25.142 version 12.1.0 Release 12)".
[4] ETSI TS 125 143 (V12.1.0) (01-2015): "Universal Mobile Telecommunications System (UMTS);
UTRA repeater conformance testing (3GPP TS 25.143 version 12.1.0 Release 12)".
[5] ETSI TS 136 104 (V12.8.0) (07-2015): "LTE; Evolved Universal Terrestrial Radio Access
(E-UTRA); Base Station (BS) radio transmission and reception (3GPP TS 36.104 version 12.8.0
Release 12)".
[6] ETSI TS 136 141 (V12.8.0) (07-2015): "LTE; Evolved Universal Terrestrial Radio Access
(E-UTRA); Base Station (BS) conformance testing (3GPP TS 36.141 version 12.8.0 Release 12)".
[7] ETSI TS 145 008 (V12.4.0) (01-2015): "Digital cellular telecommunications system (Phase 2+);
Radio subsystem link control (3GPP TS 45.008 version 12.4.0 Release 12)".
[8] ETSI EN 301 502 (V12.1.6) (01-2016): "Global System for Mobile communications (GSM); Base
Station (BS) equipment; Harmonised Standard covering the essential requirements of article 3.2 of
the Directive 2014/53/EU".
[9] ETSI TS 151 021 (V12.3.0) (01-2015): "Digital cellular telecommunications system (Phase 2+);
Base Station System (BSS) equipment specification; Radio aspects (3GPP TS 51.021
version 12.3.0 Release 12)".
[10] Void.
[11] ETSI TS 137 104 (V12.8.0) (07-2015): "Digital cellular telecommunications system (Phase 2+);
Universal Mobile Telecommunications System (UMTS); LTE; E-UTRA, UTRA and GSM/EDGE;
Multi-Standard Radio (MSR) Base Station (BS) radio transmission and reception (3GPP
TS 37.104 version 12.8.0 Release 12)".
[12] ETSI TS 137 141 (V12.8.0): "Digital cellular telecommunications system (Phase 2+); Universal
Mobile Telecommunications System (UMTS); LTE; E-UTRA, UTRA and GSM/EDGE; Multi-
Standard Radio (MSR) Base Station (BS) conformance testing (3GPP TS 37.141 version 12.8.0
Release 12)".
[13] ETSI EN 301 908-5 (V5.2.1) (09-2011): "IMT cellular networks; Harmonized EN covering the
essential requirements of article 3.2 of the R&TTE Directive; Part 5: CDMA Multi-Carrier
(cdma2000) Base Stations (BS)".
ETSI

---------------------- Page: 7 ----------------------
8 Draft ETSI EN 301 489-50 V2.1.0 (2016-06)
[14] ETSI EN 301 908-7 (V4.2.1) (03-2010): "Electromagnetic compatibility and Radio spectrum
Matters (ERM); Base Stations (BS), Repeaters and User Equipment (UE) for IMT-2000 Third-
Generation cellular networks; Part 7: Harmonized EN for IMT-2000, CDMA TDD (UTRA TDD
and E-UTRA TDD) (BS) covering the essential requirements of article 3.2 of the R&TTE
Directive".
[15] ETSI EN 301 908-20 (V6.3.1) (05-2016): "IMT cellular networks; Harmonised Standard covering
the essential requirements of article 3.2 of the Directive 2014/53/EU; Part 20: OFDMA TDD
TM
WMAN (Mobile WiMAX ) TDD Base Stations (BS)".
[16] ETSI EN 301 908-22 (V6.1.0) (05-2016): "IMT cellular networks; Harmonised Standard covering
the essential requirements of article 3.2 of the Directive 2014/53/EU; Part 22: OFDMA TDD
TM
WMAN (Mobile WiMAX ) FDD Base Stations (BS)".
[17] ETSI EN 302 544-1 (V1.1.2) (01-2010): "Broadband Data Transmission Systems operating in the
2 500 MHz to 2 690 MHz frequency band; Part 1: TDD Base Stations; Harmonized EN covering
the essential requirements of article 3.2 of the R&TTE Directive".
[18] TIA-97 (2014): "Recommended Minimum Performance Standard for cdma2000 Spread Spectrum
Base Stations".
[19] TIA-2000 Series, Revision F: "Introduction to CDMA2000 spread spectrum systems **Includes
TIA-2000.1 (2013), TIA-2000.2 (2014), TIA-2000.3 (2014), TIA-2000.4 (2014), and
TIA-2000.5 (2014)**".
[20] ETSI EN 301 449 (V1.1.1) (07-2006): "Electromagnetic compatibility and Radio spectrum
Matters (ERM); Harmonized EN for CDMA spread spectrum base stations operating in the
450 MHz cellular band (CDMA 450) and 410, 450 and 870 MHz PAMR bands (CDMA-PAMR)
covering essential requirements of article 3.2 of the R&TTE Directive".
[21] ETSI EN 302 426 (V1.1.1) (09-2006): "Electromagnetic compatibility and Radio spectrum
Matters (ERM); Harmonized EN for CDMA spread spectrum Repeaters operating in the 450 MHz
cellular band (CDMA450) and the 410 MHz, 450 MHz and 870 MHz PAMR bands (CDMA-
PAMR) covering essential requirements of article 3.2 of the R&TTE Directive".
[22] ETSI TS 125 101 (V12.8.0) (07-2015): "Universal Mobile Telecommunications System (UMTS);
User Equipment (UE) radio transmission and reception (FDD) (3GPP TS 25.101 version 12.8.0
Release 12)".
[23] ETSI TS 125 102 (V12.0.0) (10-2014): "Universal Mobile Telecommunications System (UMTS);
User Equipment (UE) radio transmission and reception (TDD) (3GPP TS 25.102 version 12.0.0
Release 12)".
[24] ETSI TS 136 101 (V12.8.0) (09-2015): "LTE; Evolved Universal Terrestrial Radio Access
(E-UTRA); User Equipment (UE) radio transmission and reception (3GPP TS 36.101
version 12.8.0 Release 12)".
[25] ETSI TS 136 143 (V12.1.0) (02-2015): "LTE; Evolved Universal Terrestrial Radio Access
(E-UTRA); FDD repeater conformance testing (3GPP TS 36.143 version 12.1.0 Release 12)".
[26] ETSI TS 151 010-1 (V12.4.0) (06-2015): "Digital cellular telecommunications system (Phase 2+);
Mobile Station (MS) conformance specification; Part 1: Conformance specification (3GPP
TS 51.010-1 version 12.4.0 Release 12)".
[27] ETSI TS 137 113 (V12.3.0) (02-2015): "Digital cellular telecommunications system (Phase 2+);
Universal Mobile Telecommunications System (UMTS); LTE; E-UTRA, UTRA and GSM/EDGE;
Multi-Standard Radio (MSR) Base Station (BS) Electromagnetic Compatibility (EMC) (3GPP
TS 37.113 version 12.3.0 Release 12)".
[28] ETSI EN 301 908-1 (V11.0.1) (01-2016): "IMT cellular networks; Harmonised Standard covering
the essential requirements of article 3.2 of the Directive 2014/53/EU; Part 1: Introduction and
common requirements".
ETSI

---------------------- Page: 8 ----------------------
9 Draft ETSI EN 301 489-50 V2.1.0 (2016-06)
2.2 Informative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are not necessary for the application of the present document but they assist the
user with regard to a particular subject area.
[i.1] Directive 2014/53/EU of the European Parliament and of the Council of 16 April 2014 on the
harmonisation of the laws of the Member States relating to the making available on the market of
radio equipment and repealing Directive 1999/5/EC.
[i.2] Void.
[i.3] ETSI TS 125 104: "Universal Mobile Telecommunications System (UMTS); Base Station (BS)
radio transmission and reception (FDD) (3GPP TS 25.104)".
[i.4] ETSI TS 125 105: "Universal Mobile Telecommunications System (UMTS); Base Station (BS)
radio transmission and reception (TDD) (3GPP TS 25.105)".
[i.5] ETSI TS 125 106: "Universal Mobile Telecommunications System (UMTS); UTRA repeater radio
transmission and reception (3GPP TS 25.106)".
[i.6] ETSI TS 136 106: "LTE; Evolved Universal Terrestrial Radio Access (E-UTRA); FDD repeater
radio transmission and reception (3GPP TS 36.106)".
[i.7] Void.
[i.8] Void.
[i.9] ETSI EN 301 489 (all parts): "ElectroMagnetic Compatibility (EMC) standard for radio equipment
and services".
[i.10] Void.
[i.11] Void.
[i.12] Void.
[i.13] Void.
[i.14] Recommendation ITU-R SM.329-12: "Unwanted emissions in the spurious domain".
[i.15] Commission Implementing Decision C(2015) 5376 final of 4.8.2015 on a standardisation request
to the European Committee for Electrotechnical Standardisation and to the European
Telecommunications Standards Institute as regards radio equipment in support of Directive
2014/53/EU of the European Parliament and of the Council.
3 Definitions and abbreviations
3.1 Definitions
For the purposes of the present document, the terms and definitions given in ETSI EN 301 489-1 [1] and the following
apply:
abis interface: logical interface between a BTS and a BSC
bearer: information transmission path of defined characteristics for transfer of user data or predefined test data
ETSI

---------------------- Page: 9 ----------------------
10 Draft ETSI EN 301 489-50 V2.1.0 (2016-06)
CDMA 1x Spread Spectrum: term used to denote cdma2000 Spread Spectrum Systems and their evolution with
spreading rate 1
CDMA-PAMR: term used to denote a PAMR system, based on TIA-2000 [19] Spreading Rate 1 specifications
channel bandwidth: RF bandwidth supporting a single E-UTRA RF c
...