iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
SIST

SIST EN 300 698 V2.3.1:2019

(Main)

Radio telephone transmitters and receivers for the maritime mobile service operating in the VHF bands used on inland waterways - Harmonised Standard for access to radio spectrum and for features for emergency services

Radio telephone transmitters and receivers for the maritime mobile service operating in the VHF bands used on inland waterways - Harmonised Standard for access to radio spectrum and for features for emergency services

The present document specifies technical characteristics and methods of measurements for VHF radio transmitters and
receivers operating on board ships in frequency bands allocated to the maritime mobile service, used on inland
waterways as defined by Regional Agreements or responsible Administrations.
The present document applies to VHF transmitters and receivers fitted with a 50 Ω external antenna socket or connector
for use on board ships on inland waterways and operating in the bands between 156 MHz and 174 MHz allocated to the
maritime mobile service by the ITU Radio Regulations [1], Appendix 18.
For countries where the Automatic Transmitter Identification System (ATIS) is mandatory, the requirements of annex B
apply as well.
NOTE: The relationship between the present document and essential requirements of article 3.2 and article 3.3(g)
of Directive 2014/53/EU [i.3] is given in annex A.

Radiotelefonski oddajniki in sprejemniki za pomorske mobilne storitve, ki delujejo v pasovih VHF in se uporabljajo na celinskih vodnih poteh - Harmonizirani standard za dostop do radijskega spektra in za funkcije storitev v sili

Ta dokument določa tehnične lastnosti in metode merjenja za radijske oddajnike in sprejemnike VHF na ladjah, ki uporabljajo frekvenčne pasove, dodeljene za pomorske mobilne storitve, in se uporabljajo na celinskih vodnih poteh, kot določajo regionalni sporazumi ali pristojni upravni organi.
Ta dokument se uporablja za oddajnike in sprejemnike VHF, ki so opremljeni z zunanjo 50-ohmsko antensko vtičnico ali priključkom za uporabo na ladjah na celinskih vodnih poteh ter delujejo v pasovih med 156 MHz in 174 MHz, dodeljenih za pomorske mobilne storitve v skladu s Pravilnikom o radiokomunikacijah Mednarodne telekomunikacijske zveze [1], dodatek 18.
Za države, v katerih je obvezna uporaba avtomatskega sistema za identifikacijo radijskih oddajnikov (ATIS), se uporabljajo tudi zahteve v dodatku B.
OPOMBA: Razmerje med tem dokumentom ter bistvenimi zahtevami člena 3.2 in člena 3.3(g) Direktive 2014/53/EU [i.3] je podano v dodatku A.

General Information

Status
Published
Public Enquiry End Date
31-Oct-2018
Publication Date
05-Dec-2018
ICS
33.060.20 - Receiving and transmitting equipment
47.020.70 - Navigation and control equipment
Technical Committee
MOC - Mobile Communications
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
26-Nov-2018
Due Date
31-Jan-2019
Completion Date
06-Dec-2018
Directive
2014/53/EU - Directive 2014/53/EU of The European Parliament and of the Council of 16 April 2014 on the harmonisation of the laws of the Member States relating to the making available on the market of radio equipment and repealing Directive 1999/5/EC
Ref Project
ETSI EN 300 698 V2.3.1 (2018-11) - Radio telephone transmitters and receivers for the maritime mobile service operating in the VHF bands used on inland waterways; Harmonised Standard for access to radio spectrum and for features for emergency services

Buy Standard

EN 300 698 V2.3.1:2019EN 300 698 V2.3.1:2019
PreviousNext
Standard
EN 300 698 V2.3.1:2019
English language
54 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day
ETSI EN 300 698 V2.3.1 (2018-11) - Radio telephone transmitters and receivers for the maritime mobile service operating in the VHF bands used on inland waterways; Harmonised Standard for access to radio spectrum and for features for emergency servicesETSI EN 300 698 V2.3.1 (2018-11) - Radio telephone transmitters and receivers for the maritime mobile service operating in the VHF bands used on inland waterways; Harmonised Standard for access to radio spectrum and for features for emergency services
PreviousNext
Standard
ETSI EN 300 698 V2.3.1 (2018-11) - Radio telephone transmitters and receivers for the maritime mobile service operating in the VHF bands used on inland waterways; Harmonised Standard for access to radio spectrum and for features for emergency services
English language
54 pages
sale 15% off
Preview
sale 15% off
Preview
ETSI EN 300 698 V2.3.0 (2018-08) - Radio telephone transmitters and receivers for the maritime mobile service operating in the VHF bands used on inland waterways; Harmonised Standard for access to radio spectrum and for features for emergency servicesETSI EN 300 698 V2.3.0 (2018-08) - Radio telephone transmitters and receivers for the maritime mobile service operating in the VHF bands used on inland waterways; Harmonised Standard for access to radio spectrum and for features for emergency services
PreviousNext
Standard
ETSI EN 300 698 V2.3.0 (2018-08) - Radio telephone transmitters and receivers for the maritime mobile service operating in the VHF bands used on inland waterways; Harmonised Standard for access to radio spectrum and for features for emergency services
English language
54 pages
sale 15% off
Preview
sale 15% off
Preview
prEN 300 698 V2.3.0:2018prEN 300 698 V2.3.0:2018
PreviousNext
Draft
prEN 300 698 V2.3.0:2018
English language
54 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Radiotelefonski oddajniki in sprejemniki za pomorske mobilne storitve, ki delujejo v pasovih VHF in se uporabljajo na celinskih vodnih poteh - Harmonizirani standard za dostop do radijskega spektra in za funkcije storitev v siliRadio telephone transmitters and receivers for the maritime mobile service operating in the VHF bands used on inland waterways - Harmonised Standard for access to radio spectrum and for features for emergency services47.020.70Navigacijska in krmilna opremaNavigation and control equipment33.060.20Sprejemna in oddajna opremaReceiving and transmitting equipmentICS:Ta slovenski standard je istoveten z:ETSI EN 300 698 V2.3.1 (2018-11)SIST EN 300 698 V2.3.1:2019en01-januar-2019SIST EN 300 698 V2.3.1:2019SLOVENSKI
STANDARD



SIST EN 300 698 V2.3.1:2019



ETSI EN 300 698 V2.3.1 (2018-11) Radio telephone transmitters and receivers for the maritime mobile service operating in the VHF bands used on inland waterways; Harmonised Standard for access to radio spectrum and for features for emergency services
HARMONISED EUROPEAN STANDARD SIST EN 300 698 V2.3.1:2019



ETSI ETSI EN 300 698 V2.3.1 (2018-11) 2
Reference REN/ERM-TG26-597 Keywords harmonised standard, maritime, radio, VHF ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00
Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C Association à but non lucratif enregistrée à la Sous-Préfecture de Grasse (06) N° 7803/88
Important notice The present document can be downloaded from: http://www.etsi.org/standards-search The present document may be made available in electronic versions and/or in print. The content of any electronic and/or print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx If you find errors in the present document, please send your comment to one of the following services: https://portal.etsi.org/People/CommiteeSupportStaff.aspx Copyright Notification No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm except as authorized by written permission of ETSI. The content of the PDF version shall not be modified without the written authorization of ETSI. The copyright and the foregoing restriction extend to reproduction in all media.
© ETSI 2018. All rights reserved.
DECTTM, PLUGTESTSTM, UMTSTM and the ETSI logo are trademarks of ETSI registered for the benefit of its Members. 3GPPTM and LTETM are trademarks of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. oneM2M™ logo is a trademark of ETSI registered for the benefit of its Members and of the oneM2M Partners. GSM® and the GSM logo are trademarks registered and owned by the GSM Association. SIST EN 300 698 V2.3.1:2019



ETSI ETSI EN 300 698 V2.3.1 (2018-11) 3 Contents Intellectual Property Rights . 7 Foreword . 7 Modal verbs terminology . 7 1 Scope . 8 2 References . 8 2.1 Normative references . 8 2.2 Informative references . 8 3 Definitions, symbols and abbreviations . 9 3.1 Definitions . 9 3.2 Symbols . 9 3.3 Abbreviations . 9 4 General and operational requirements . 9 4.0 Conformance . 9 4.1 Construction . 10 4.2 Controls and indicators . 10 4.3 Handset and loudspeaker . 11 4.4 Switching time . 11 4.5 Safety precautions . 11 4.6 Class of emission and modulation characteristics . 12 4.7 Labelling. 12 4.8 Warm up . 12 5 Test conditions, power sources and ambient temperatures . 12 5.1 Normal and extreme test conditions . 12 5.2 Test power source . 12 5.3 Normal test conditions . 12 5.3.1 Normal temperature and humidity . 12 5.3.2 Normal power sources . 13 5.3.2.1 Mains voltage and frequency . 13 5.3.2.2 Battery power source. 13 5.3.2.3 Other power sources . 13 5.4 Extreme test conditions . 13 5.4.1 Extreme temperatures . 13 5.4.2 Extreme values of test power sources . 13 5.4.2.1 Mains voltage . 13 5.4.2.2 Battery power source. 13 5.4.2.3 Other power sources . 13 5.5 Procedure for tests at extreme temperatures . 13 6 General conditions of measurement . 14 6.1 Arrangements for test signals applied to the receiver . 14 6.2 Squelch . 14 6.3 Normal test modulation . 14 6.4 Artificial antenna . 14 6.5 Arrangements for test signals applied to the transmitter . 14 6.6 Tests on equipment with a duplex filter . 14 6.7 Test channels . 14 6.8 Transmission time limitation . 14 6.9 Reference Bandwidths for emission measurements . 15 7 Environmental tests . 15 7.1 Introduction . 15 7.2 Procedure . 15 7.3 Performance check . 15 7.4 Vibration. 16 SIST EN 300 698 V2.3.1:2019



ETSI ETSI EN 300 698 V2.3.1 (2018-11) 4 7.5 Damp heat cycle . 16 8 Transmitter . 16 8.0 General . 16 8.1 Frequency error . 17 8.1.1 Definition . 17 8.1.2 Method of measurement . 17 8.1.3 Limits . 17 8.2 Carrier power . 17 8.2.1 Definitions . 17 8.2.2 Method of measurement . 17 8.2.3 Limits . 17 8.2.3.1 Normal test conditions . 17 8.2.3.2 Extreme test conditions . 17 8.3 Frequency deviation . 18 8.3.1 Definition . 18 8.3.2 The maximum frequency deviation at modulation frequencies below 3 kHz . 18 8.3.2.1 Method of measurement . 18 8.3.2.2 Limits . 18 8.3.3 The maximum frequency deviation at modulation frequencies above 3 kHz . 18 8.3.3.1 Method of measurement . 18 8.3.3.2 Limits . 18 8.4 Limitation characteristics of the modulator . 19 8.4.1 Definition . 19 8.4.2 Method of measurement . 19 8.4.3 Limits . 19 8.5 Sensitivity of the modulator, including microphone . 19 8.5.1 Definition . 19 8.5.2 Method of measurement . 19 8.5.3 Limits . 20 8.6 Audio frequency response . 20 8.6.1 Definition . 20 8.6.2 Method of measurement . 20 8.6.3 Limit . 20 8.7 Audio frequency harmonic distortion of the emission. 21 8.7.1 Definition . 21 8.7.2 Method of measurement . 21 8.7.2.1 General . 21 8.7.2.2 Normal test conditions . 22 8.7.2.3 Extreme test conditions . 22 8.7.3 Limit . 22 8.8 Adjacent channel power . 22 8.8.1 Definition . 22 8.8.2 Method of measurement . 22 8.8.3 Limits . 22 8.9 Conducted spurious emissions conveyed to the antenna . 23 8.9.1 Definition . 23 8.9.2 Method of measurement . 23 8.9.3 Limit . 23 8.10 Residual modulation of the transmitter . 23 8.10.1 Definition . 23 8.10.2 Method of measurement . 23 8.10.3 Limit . 23 8.11 Transient frequency behaviour of the transmitter . 23 8.11.1 Definitions . 23 8.11.2 Method of measurement . 24 8.11.3 Limits . 25 8.12 Cabinet radiation and conducted spurious emissions other than those conveyed to the antenna . 27 8.12.1 Definitions . 27 8.12.2 Method of measurement . 27 8.12.3 Limits . 28 SIST EN 300 698 V2.3.1:2019



ETSI ETSI EN 300 698 V2.3.1 (2018-11) 5 9 Receiver . 28 9.1 Harmonic distortion and rated audio frequency output power . 28 9.1.1 Definition . 28 9.1.2 Method of measurement . 28 9.1.3 Limits . 29 9.2 Audio frequency response . 29 9.2.1 Definition . 29 9.2.2 Method of measurement . 29 9.2.3 Limits . 29 9.3 Maximum usable sensitivity . 30 9.3.1 Definition . 30 9.3.2 Method of measurement . 31 9.3.3 Limits . 31 9.4 Co-channel rejection. 31 9.4.1 Definition . 31 9.4.2 Method of measurement . 31 9.4.3 Limit . 31 9.5 Adjacent channel selectivity . 31 9.5.1 Definition . 31 9.5.2 Method of measurement . 32 9.5.3 Limits . 32 9.6 Spurious response rejection . 32 9.6.1 Definition . 32 9.6.2 Method of measurement . 32 9.6.3 Limit . 32 9.7 Intermodulation response . 33 9.7.1 Definition . 33 9.7.2 Method of measurement . 33 9.7.3 Limit . 33 9.8 Blocking or desensitization . 33 9.8.1 Definition . 33 9.8.2 Method of measurement . 33 9.8.3 Limit . 34 9.9 Conducted spurious emissions conveyed to the antenna . 34 9.9.1 Definition . 34 9.9.2 Method of measurement . 34 9.9.3 Limit . 34 9.10 Amplitude response of the receiver limiter . 34 9.10.1 Definition . 34 9.10.2 Method of measurement . 34 9.10.3 Limit . 34 9.11 Receiver noise and hum level . 34 9.11.1 Definition . 34 9.11.2 Method of measurement . 35 9.11.3 Limit . 35 9.12 Squelch operation . 35 9.12.1 Definition . 35 9.12.2 Method of measurement . 35 9.12.3 Limits . 35 9.13 Squelch hysteresis . 36 9.13.1 Definition . 36 9
...

ETSI EN 300 698 V2.3.1 (2018-11)






HARMONISED EUROPEAN STANDARD
Radio telephone transmitters and receivers
for the maritime mobile service operating
in the VHF bands used on inland waterways;
Harmonised Standard for access to radio spectrum
and for features for emergency services

---------------------- Page: 1 ----------------------
2 ETSI EN 300 698 V2.3.1 (2018-11)



Reference
REN/ERM-TG26-597
Keywords
harmonised standard, maritime, radio, VHF
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE

Tel.: +33 4 92 94 42 00  Fax: +33 4 93 65 47 16

Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88

Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the
print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.

© ETSI 2018.
All rights reserved.

TM TM TM
DECT , PLUGTESTS , UMTS and the ETSI logo are trademarks of ETSI registered for the benefit of its Members.
TM TM
3GPP and LTE are trademarks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
oneM2M™ logo is a trademark of ETSI registered for the benefit of its Members and
of the oneM2M Partners.
®
GSM and the GSM logo are trademarks registered and owned by the GSM Association.
ETSI

---------------------- Page: 2 ----------------------
3 ETSI EN 300 698 V2.3.1 (2018-11)
Contents
Intellectual Property Rights . 7
Foreword . 7
Modal verbs terminology . 7
1 Scope . 8
2 References . 8
2.1 Normative references . 8
2.2 Informative references . 8
3 Definitions, symbols and abbreviations . 9
3.1 Definitions . 9
3.2 Symbols . 9
3.3 Abbreviations . 9
4 General and operational requirements . 9
4.0 Conformance . 9
4.1 Construction . 10
4.2 Controls and indicators . 10
4.3 Handset and loudspeaker . 11
4.4 Switching time . 11
4.5 Safety precautions . 11
4.6 Class of emission and modulation characteristics . 12
4.7 Labelling. 12
4.8 Warm up . 12
5 Test conditions, power sources and ambient temperatures . 12
5.1 Normal and extreme test conditions . 12
5.2 Test power source . 12
5.3 Normal test conditions . 12
5.3.1 Normal temperature and humidity . 12
5.3.2 Normal power sources . 13
5.3.2.1 Mains voltage and frequency . 13
5.3.2.2 Battery power source. 13
5.3.2.3 Other power sources . 13
5.4 Extreme test conditions . 13
5.4.1 Extreme temperatures . 13
5.4.2 Extreme values of test power sources . 13
5.4.2.1 Mains voltage . 13
5.4.2.2 Battery power source. 13
5.4.2.3 Other power sources . 13
5.5 Procedure for tests at extreme temperatures . 13
6 General conditions of measurement . 14
6.1 Arrangements for test signals applied to the receiver . 14
6.2 Squelch . 14
6.3 Normal test modulation . 14
6.4 Artificial antenna . 14
6.5 Arrangements for test signals applied to the transmitter . 14
6.6 Tests on equipment with a duplex filter . 14
6.7 Test channels . 14
6.8 Transmission time limitation . 14
6.9 Reference Bandwidths for emission measurements . 15
7 Environmental tests . 15
7.1 Introduction . 15
7.2 Procedure . 15
7.3 Performance check . 15
7.4 Vibration. 16
ETSI

---------------------- Page: 3 ----------------------
4 ETSI EN 300 698 V2.3.1 (2018-11)
7.5 Damp heat cycle . 16
8 Transmitter . 16
8.0 General . 16
8.1 Frequency error . 17
8.1.1 Definition . 17
8.1.2 Method of measurement . 17
8.1.3 Limits . 17
8.2 Carrier power . 17
8.2.1 Definitions . 17
8.2.2 Method of measurement . 17
8.2.3 Limits . 17
8.2.3.1 Normal test conditions . 17
8.2.3.2 Extreme test conditions . 17
8.3 Frequency deviation . 18
8.3.1 Definition . 18
8.3.2 The maximum frequency deviation at modulation frequencies below 3 kHz . 18
8.3.2.1 Method of measurement . 18
8.3.2.2 Limits . 18
8.3.3 The maximum frequency deviation at modulation frequencies above 3 kHz . 18
8.3.3.1 Method of measurement . 18
8.3.3.2 Limits . 18
8.4 Limitation characteristics of the modulator . 19
8.4.1 Definition . 19
8.4.2 Method of measurement . 19
8.4.3 Limits . 19
8.5 Sensitivity of the modulator, including microphone . 19
8.5.1 Definition . 19
8.5.2 Method of measurement . 19
8.5.3 Limits . 20
8.6 Audio frequency response . 20
8.6.1 Definition . 20
8.6.2 Method of measurement . 20
8.6.3 Limit . 20
8.7 Audio frequency harmonic distortion of the emission. 21
8.7.1 Definition . 21
8.7.2 Method of measurement . 21
8.7.2.1 General . 21
8.7.2.2 Normal test conditions . 22
8.7.2.3 Extreme test conditions . 22
8.7.3 Limit . 22
8.8 Adjacent channel power . 22
8.8.1 Definition . 22
8.8.2 Method of measurement . 22
8.8.3 Limits . 22
8.9 Conducted spurious emissions conveyed to the antenna . 23
8.9.1 Definition . 23
8.9.2 Method of measurement . 23
8.9.3 Limit . 23
8.10 Residual modulation of the transmitter . 23
8.10.1 Definition . 23
8.10.2 Method of measurement . 23
8.10.3 Limit . 23
8.11 Transient frequency behaviour of the transmitter . 23
8.11.1 Definitions . 23
8.11.2 Method of measurement . 24
8.11.3 Limits . 25
8.12 Cabinet radiation and conducted spurious emissions other than those conveyed to the antenna . 27
8.12.1 Definitions . 27
8.12.2 Method of measurement . 27
8.12.3 Limits . 28
ETSI

---------------------- Page: 4 ----------------------
5 ETSI EN 300 698 V2.3.1 (2018-11)
9 Receiver . 28
9.1 Harmonic distortion and rated audio frequency output power . 28
9.1.1 Definition . 28
9.1.2 Method of measurement . 28
9.1.3 Limits . 29
9.2 Audio frequency response . 29
9.2.1 Definition . 29
9.2.2 Method of measurement . 29
9.2.3 Limits . 29
9.3 Maximum usable sensitivity . 30
9.3.1 Definition . 30
9.3.2 Method of measurement . 31
9.3.3 Limits . 31
9.4 Co-channel rejection. 31
9.4.1 Definition . 31
9.4.2 Method of measurement . 31
9.4.3 Limit . 31
9.5 Adjacent channel selectivity . 31
9.5.1 Definition . 31
9.5.2 Method of measurement . 32
9.5.3 Limits . 32
9.6 Spurious response rejection . 32
9.6.1 Definition . 32
9.6.2 Method of measurement . 32
9.6.3 Limit . 32
9.7 Intermodulation response . 33
9.7.1 Definition . 33
9.7.2 Method of measurement . 33
9.7.3 Limit . 33
9.8 Blocking or desensitization . 33
9.8.1 Definition . 33
9.8.2 Method of measurement . 33
9.8.3 Limit . 34
9.9 Conducted spurious emissions conveyed to the antenna . 34
9.9.1 Definition . 34
9.9.2 Method of measurement . 34
9.9.3 Limit . 34
9.10 Amplitude response of the receiver limiter . 34
9.10.1 Definition . 34
9.10.2 Method of measurement . 34
9.10.3 Limit . 34
9.11 Receiver noise and hum level . 34
9.11.1 Definition . 34
9.11.2 Method of measurement . 35
9.11.3 Limit . 35
9.12 Squelch operation . 35
9.12.1 Definition . 35
9.12.2 Method of measurement . 35
9.12.3 Limits . 35
9.13 Squelch hysteresis . 36
9.13.1 Definition . 36
9.13.2 Method of measurement . 36
9.13.3 Limit . 36
9.14 Radiated spurious emissions. 36
9.14.1 Definition .
...

Draft ETSI EN 300 698 V2.3.0 (2018-08)






HARMONISED EUROPEAN STANDARD
Radio telephone transmitters and receivers
for the maritime mobile service operating
in the VHF bands used on inland waterways;
Harmonised Standard for access to radio spectrum and for
features for emergency services

---------------------- Page: 1 ----------------------
2 Draft ETSI EN 300 698 V2.3.0 (2018-08)



Reference
REN/ERM-TG26-597
Keywords
harmonised standard, maritime, radio, VHF
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE

Tel.: +33 4 92 94 42 00  Fax: +33 4 93 65 47 16

Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88

Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the
print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.

© ETSI 2018.
All rights reserved.

TM TM TM
DECT , PLUGTESTS , UMTS and the ETSI logo are trademarks of ETSI registered for the benefit of its Members.
TM TM
3GPP and LTE are trademarks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
oneM2M logo is protected for the benefit of its Members.
®
GSM and the GSM logo are trademarks registered and owned by the GSM Association.
ETSI

---------------------- Page: 2 ----------------------
3 Draft ETSI EN 300 698 V2.3.0 (2018-08)
Contents
Intellectual Property Rights . 7
Foreword . 7
Modal verbs terminology . 7
1 Scope . 8
2 References . 8
2.1 Normative references . 8
2.2 Informative references . 8
3 Definitions, symbols and abbreviations . 9
3.1 Definitions . 9
3.2 Symbols . 9
3.3 Abbreviations . 9
4 General and operational requirements . 9
4.0 Conformance . 9
4.1 Construction . 10
4.2 Controls and indicators . 10
4.3 Handset and loudspeaker . 11
4.4 Switching time . 11
4.5 Safety precautions . 11
4.6 Class of emission and modulation characteristics . 12
4.7 Labelling. 12
4.8 Warm up . 12
5 Test conditions, power sources and ambient temperatures . 12
5.1 Normal and extreme test conditions . 12
5.2 Test power source . 12
5.3 Normal test conditions . 13
5.3.1 Normal temperature and humidity . 13
5.3.2 Normal power sources . 13
5.3.2.1 Mains voltage and frequency . 13
5.3.2.2 Battery power source. 13
5.3.2.3 Other power sources . 13
5.4 Extreme test conditions . 13
5.4.1 Extreme temperatures . 13
5.4.2 Extreme values of test power sources . 13
5.4.2.1 Mains voltage . 13
5.4.2.2 Battery power source. 13
5.4.2.3 Other power sources . 13
5.5 Procedure for tests at extreme temperatures . 14
6 General conditions of measurement . 14
6.1 Arrangements for test signals applied to the receiver . 14
6.2 Squelch . 14
6.3 Normal test modulation . 14
6.4 Artificial antenna . 14
6.5 Arrangements for test signals applied to the transmitter . 14
6.6 Tests on equipment with a duplex filter . 15
6.7 Test channels . 15
6.8 Transmission time limitation . 15
6.9 Reference Bandwidths for emission measurements . 15
7 Environmental tests . 15
7.1 Introduction . 15
7.2 Procedure . 15
7.3 Performance check . 16
7.4 Vibration. 16
ETSI

---------------------- Page: 3 ----------------------
4 Draft ETSI EN 300 698 V2.3.0 (2018-08)
7.5 Damp heat cycle . 16
8 Transmitter . 17
8.0 General . 17
8.1 Frequency error . 17
8.1.1 Definition . 17
8.1.2 Method of measurement . 17
8.1.3 Limits . 17
8.2 Carrier power . 17
8.2.1 Definitions . 17
8.2.2 Method of measurement . 17
8.2.3 Limits . 17
8.2.3.1 Normal test conditions . 17
8.2.3.2 Extreme test conditions . 18
8.3 Frequency deviation . 18
8.3.1 Definition . 18
8.3.2 The maximum frequency deviation at modulation frequencies below 3 kHz . 18
8.3.2.1 Method of measurement . 18
8.3.2.2 Limits . 18
8.3.3 The maximum frequency deviation at modulation frequencies above 3 kHz . 18
8.3.3.1 Method of measurement . 18
8.3.3.2 Limits . 18
8.4 Limitation characteristics of the modulator . 19
8.4.1 Definition . 19
8.4.2 Method of measurement . 19
8.4.3 Limits . 19
8.5 Sensitivity of the modulator, including microphone . 19
8.5.1 Definition . 19
8.5.2 Method of measurement . 20
8.5.3 Limits . 20
8.6 Audio frequency response . 20
8.6.1 Definition . 20
8.6.2 Method of measurement . 20
8.6.3 Limit . 20
8.7 Audio frequency harmonic distortion of the emission. 21
8.7.1 Definition . 21
8.7.2 Method of measurement . 21
8.7.2.1 General . 21
8.7.2.2 Normal test conditions . 22
8.7.2.3 Extreme test conditions . 22
8.7.3 Limit . 22
8.8 Adjacent channel power . 22
8.8.1 Definition . 22
8.8.2 Method of measurement . 22
8.8.3 Limits . 22
8.9 Conducted spurious emissions conveyed to the antenna . 23
8.9.1 Definition . 23
8.9.2 Method of measurement . 23
8.9.3 Limit . 23
8.10 Residual modulation of the transmitter . 23
8.10.1 Definition . 23
8.10.2 Method of measurement . 23
8.10.3 Limit . 23
8.11 Transient frequency behaviour of the transmitter . 23
8.11.1 Definitions . 23
8.11.2 Method of measurement . 24
8.11.3 Limits . 25
8.12 Cabinet radiation and conducted spurious emissions other than those conveyed to the antenna . 27
8.12.1 Definitions . 27
8.12.2 Method of measurement . 27
8.12.3 Limits . 28
ETSI

---------------------- Page: 4 ----------------------
5 Draft ETSI EN 300 698 V2.3.0 (2018-08)
9 Receiver . 28
9.1 Harmonic distortion and rated audio frequency output power . 28
9.1.1 Definition . 28
9.1.2 Method of measurement . 28
9.1.3 Limits . 29
9.2 Audio frequency response . 29
9.2.1 Definition . 29
9.2.2 Method of measurement . 29
9.2.3 Limits . 30
9.3 Maximum usable sensitivity . 30
9.3.1 Definition . 30
9.3.2 Method of measurement . 31
9.3.3 Limits . 31
9.4 Co-channel rejection. 31
9.4.1 Definition . 31
9.4.2 Method of measurement . 31
9.4.3 Limit . 31
9.5 Adjacent channel selectivity . 31
9.5.1 Definition . 31
9.5.2 Method of measurement . 32
9.5.3 Limits . 32
9.6 Spurious response rejection . 32
9.6.1 Definition . 32
9.6.2 Method of measurement . 32
9.6.3 Limit . 32
9.7 Intermodulation response . 33
9.7.1 Definition . 33
9.7.2 Method of measurement . 33
9.7.3 Limit . 33
9.8 Blocking or desensitization . 33
9.8.1 Definition . 33
9.8.2 Method of measurement . 33
9.8.3 Limit . 34
9.9 Conducted spurious emissions conveyed to the antenna . 34
9.9.1 Definition . 34
9.9.2 Method of measurement . 34
9.9.3 Limit . 34
9.10 Amplitude response of the receiver limiter . 34
9.10.1 Definition . 34
9.10.2 Method of measurement . 34
9.10.3 Limit . 34
9.11 Receiver noise and hum level . 34
9.11.1 Definition . 34
9.11.2 Method of measurement . 35
9.11.3 Limit . 35
9.12 Squelch operation . 35
9.12.1 Definition . 35
9.12.2 Method of measurement . 35
9.12.3 Limits . 35
9.13 Squelch hysteresis . 36
9.13.1 Definition . 36
9.13.2 Method of measurement . 36
9.13.3 Limit . 36
9.14 Radiated spurious emissions. 36
9.14.1 Definition .
...

SLOVENSKI STANDARD
oSIST prEN 300 698 V2.3.0:2018
01-oktober-2018
Radiotelefonski oddajniki in sprejemniki za pomorske mobilne storitve, ki delujejo
v pasovih VHF in se uporabljajo na celinskih vodnih poteh - Harmonizirani
standard za dostop do radijskega spektra in za funkcije storitev v sili
Radio telephone transmitters and receivers for the maritime mobile service operating in
the VHF bands used on inland waterways - Harmonised Standard for access to radio
spectrum and for features for emergency services
Ta slovenski standard je istoveten z: ETSI EN 300 698 V2.3.0 (2018-08)
ICS:
33.060.20 Sprejemna in oddajna Receiving and transmitting
oprema equipment
47.020.70 Navigacijska in krmilna Navigation and control
oprema equipment
oSIST prEN 300 698 V2.3.0:2018 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
oSIST prEN 300 698 V2.3.0:2018

---------------------- Page: 2 ----------------------
oSIST prEN 300 698 V2.3.0:2018
Draft ETSI EN 300 698 V2.3.0 (2018-08)






HARMONISED EUROPEAN STANDARD
Radio telephone transmitters and receivers
for the maritime mobile service operating
in the VHF bands used on inland waterways;
Harmonised Standard for access to radio spectrum and for
features for emergency services

---------------------- Page: 3 ----------------------
oSIST prEN 300 698 V2.3.0:2018

2 Draft ETSI EN 300 698 V2.3.0 (2018-08)



Reference
REN/ERM-TG26-597
Keywords
harmonised standard, maritime, radio, VHF
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE

Tel.: +33 4 92 94 42 00  Fax: +33 4 93 65 47 16

Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88

Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the
print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.

© ETSI 2018.
All rights reserved.

TM TM TM
DECT , PLUGTESTS , UMTS and the ETSI logo are trademarks of ETSI registered for the benefit of its Members.
TM TM
3GPP and LTE are trademarks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
oneM2M logo is protected for the benefit of its Members.
®
GSM and the GSM logo are trademarks registered and owned by the GSM Association.
ETSI

---------------------- Page: 4 ----------------------
oSIST prEN 300 698 V2.3.0:2018

3 Draft ETSI EN 300 698 V2.3.0 (2018-08)
Contents
Intellectual Property Rights . 7
Foreword . 7
Modal verbs terminology . 7
1 Scope . 8
2 References . 8
2.1 Normative references . 8
2.2 Informative references . 8
3 Definitions, symbols and abbreviations . 9
3.1 Definitions . 9
3.2 Symbols . 9
3.3 Abbreviations . 9
4 General and operational requirements . 9
4.0 Conformance . 9
4.1 Construction . 10
4.2 Controls and indicators . 10
4.3 Handset and loudspeaker . 11
4.4 Switching time . 11
4.5 Safety precautions . 11
4.6 Class of emission and modulation characteristics . 12
4.7 Labelling. 12
4.8 Warm up . 12
5 Test conditions, power sources and ambient temperatures . 12
5.1 Normal and extreme test conditions . 12
5.2 Test power source . 12
5.3 Normal test conditions . 13
5.3.1 Normal temperature and humidity . 13
5.3.2 Normal power sources . 13
5.3.2.1 Mains voltage and frequency . 13
5.3.2.2 Battery power source. 13
5.3.2.3 Other power sources . 13
5.4 Extreme test conditions . 13
5.4.1 Extreme temperatures . 13
5.4.2 Extreme values of test power sources . 13
5.4.2.1 Mains voltage . 13
5.4.2.2 Battery power source. 13
5.4.2.3 Other power sources . 13
5.5 Procedure for tests at extreme temperatures . 14
6 General conditions of measurement . 14
6.1 Arrangements for test signals applied to the receiver . 14
6.2 Squelch . 14
6.3 Normal test modulation . 14
6.4 Artificial antenna . 14
6.5 Arrangements for test signals applied to the transmitter . 14
6.6 Tests on equipment with a duplex filter . 15
6.7 Test channels . 15
6.8 Transmission time limitation . 15
6.9 Reference Bandwidths for emission measurements . 15
7 Environmental tests . 15
7.1 Introduction . 15
7.2 Procedure . 15
7.3 Performance check . 16
7.4 Vibration. 16
ETSI

---------------------- Page: 5 ----------------------
oSIST prEN 300 698 V2.3.0:2018

4 Draft ETSI EN 300 698 V2.3.0 (2018-08)
7.5 Damp heat cycle . 16
8 Transmitter . 17
8.0 General . 17
8.1 Frequency error . 17
8.1.1 Definition . 17
8.1.2 Method of measurement . 17
8.1.3 Limits . 17
8.2 Carrier power . 17
8.2.1 Definitions . 17
8.2.2 Method of measurement . 17
8.2.3 Limits . 17
8.2.3.1 Normal test conditions . 17
8.2.3.2 Extreme test conditions . 18
8.3 Frequency deviation . 18
8.3.1 Definition . 18
8.3.2 The maximum frequency deviation at modulation frequencies below 3 kHz . 18
8.3.2.1 Method of measurement . 18
8.3.2.2 Limits . 18
8.3.3 The maximum frequency deviation at modulation frequencies above 3 kHz . 18
8.3.3.1 Method of measurement . 18
8.3.3.2 Limits . 18
8.4 Limitation characteristics of the modulator . 19
8.4.1 Definition . 19
8.4.2 Method of measurement . 19
8.4.3 Limits . 19
8.5 Sensitivity of the modulator, including microphone . 19
8.5.1 Definition . 19
8.5.2 Method of measurement . 20
8.5.3 Limits . 20
8.6 Audio frequency response . 20
8.6.1 Definition . 20
8.6.2 Method of measurement . 20
8.6.3 Limit . 20
8.7 Audio frequency harmonic distortion of the emission. 21
8.7.1 Definition . 21
8.7.2 Method of measurement . 21
8.7.2.1 General . 21
8.7.2.2 Normal test conditions . 22
8.7.2.3 Extreme test conditions . 22
8.7.3 Limit . 22
8.8 Adjacent channel power . 22
8.8.1 Definition . 22
8.8.2 Method of measurement . 22
8.8.3 Limits . 22
8.9 Conducted spurious emissions conveyed to the antenna . 23
8.9.1 Definition . 23
8.9.2 Method of measurement . 23
8.9.3 Limit . 23
8.10 Residual modulation of the transmitter . 23
8.10.1 Definition . 23
8.10.2 Method of measurement . 23
8.10.3 Limit . 23
8.11 Transient frequency behaviour of the transmitter . 23
8.11.1 Definitions . 23
8.11.2 Method of measurement . 24
8.11.3 Limits . 25
8.12 Cabinet radiation and conducted spurious emissions other than those conveyed to the antenna . 27
8.12.1 Definitions . 27
8.12.2 Method of measurement . 27
8.12.3 Limits . 28
ETSI

---------------------- Page: 6 ----------------------
oSIST prEN 300 698 V2.3.0:2018

5 Draft ETSI EN 300 698 V2.3.0 (2018-08)
9 Receiver . 28
9.1 Harmonic distortion and rated audio frequency output power . 28
9.1.1 Definition . 28
9.1.2 Method of measurement . 28
9.1.3 Limits . 29
9.2 Audio frequency response . 29
9.2.1 Definition . 29
9.2.2 Method of measurement . 29
9.2.3 Limits . 30
9.3 Maximum usable sensitivity . 30
9.3.1 Definition . 30
9.3.2 Method of measurement . 31
9.3.3 Limits . 31
9.4 Co-channel rejection. 31
9.4.1 Definition . 31
9.4.2 Method of measurement . 31
9.4.3 Limit . 31
9.5 Adjacent channel selectivity . 31
9.5.1 Definition . 31
9.5.2 Method of measurement . 32
9.5.3 Limits . 32
9.6 Spurious response rejection . 32
9.6.1 Definition . 32
9.6.2 Method of measurement . 32
9.6.3 Limit . 32
9.7 Intermodulation response . 33
9.7.1 Definition . 33
9.7.2 Method of measurement . 33
9.7.3 Limit . 33
9.8 Blocking or desensitization . 33
9.8.1 Definition . 33
9.8.2 Method of measurement . 33
9.8.3 Limit . 34
9.9 Conducted spurious emissions conveyed to the antenna . 34
9.9.1 Definition . 34
9.9.2 Method of measurement . 34
9.9.3 Limit . 34
9.10 Amplitude response of the receiver limiter . 34
9.10.1 Definition . 34
9.10.2 Method of measurement . 34
9.10.3 Limit . 34
9.11 Receiver noise and hum level . 34
9.11.1 Definition . 34
9.11.2 Method of measurement . 35
9.11.3 Limit . 35
9.12 Squelch operation . 35
9.12.1 Definition . 35
9.12.2 Method of measurement .
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

SIST
SIST EN 300 338-7 V1.1.1:2022(Main)
Technical characteristics and methods of measurement for equipment for generation, transmission and reception of Digital Selective Calling (DSC) in the maritime MF, MF/HF and/or VHF mobile service - Part 7: Implementation of Bridge Alert Management (BAM) in DSC radio equipment
ETSI EN 300 338-7 V1.1.1 (2022-04)

The present document specifies the minimum requirements for GMDSS radiocommunication system using Digital
Selective Calling (DSC) Class A, with the capability to operate on a SOLAS bridge with the application of SOLAS
regulation V/15 [i.4] and thus implementing the BAM concept defined by IMO in MSC.302(87) [8].

  • Standard
    35 pages
    English language
    sale 15% off
  • Standard
    35 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Standard
    35 pages
    English language
    sale 15% off
  • Standard
    35 pages
    English language
    sale 15% off
  • Draft
    35 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 300 338-8 V1.1.1:2022(Main)
Technical characteristics and methods of measurement for equipment for generation, transmission and reception of Digital Selective Calling (DSC) in the maritime MF, MF/HF and/or VHF mobile service - Part 8: Enabling DSC radio equipment with remote control capabilities
ETSI EN 300 338-8 V1.1.1 (2022-02)

The present document states minimum requirements for GMDSS radiocommunication equipment using Digital Selective
Calling (DSC) Class A [2], with the capability to fully operate handling of the automated procedures defined in part 2 of this
multi-part deliverable, see ETSI EN 300 338-2 [2] from a remote position such as a central HMI.
In addition other proprietary control interfaces may apply to support full remote control of other DSC EQUIPMENT
functions.
Such proprietary control interfaces (whether based on proprietary IEC 61162-1 [3] sentences or other protocols) are not part
of the present document, and may co-exist with the requirements in the present document.

  • Standard
    94 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Standard
    94 pages
    English language
    sale 15% off
  • Standard
    94 pages
    English language
    sale 15% off
  • Draft
    94 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 300 338-1 V1.6.1:2021(Main)
Technical characteristics and methods of measurement for equipment for generation, transmission and reception of Digital Selective Calling (DSC) in the maritime MF, MF/HF and/or VHF mobile service - Part 1: Common requirements
ETSI EN 300 338-1 V1.6.1 (2021-05)

The present document states the minimum requirements for equipment to be used for generation, transmission and
reception of Digital Selective Calling (DSC) for use on board ships.
DSC is intended to be used in the Medium Frequency (MF), High Frequency (HF) and Very High Frequency (VHF)
bands of the Maritime Mobile Service (MMS), for distress, urgency and safety communication and general
communications.
The present document is part 1 of a multi-part deliverable that covers the requirements to be fulfilled by:
• DSC equipment integrated with a transmitter and/or a receiver;
• DSC equipment not integrated with a transmitter and/or a receiver.
These requirements include the relevant provisions of the ITU Radio Regulations [i.15] and Recommendations ITU-R
M.493-15 [2], M.541-10 [3], M.689-3 [4] and M.1082-1 [5], the International Convention for the Safety Of Life At Sea
(SOLAS) [i.14], and the following resolutions/circulars of the International Maritime Organization (IMO):
A.694(17) [14], A.803(19) [15] amended by MSC.68(68) Annex 1 [17], A.804(19) [16], MSC.68(68) Annex 2 [17],
A.806(19) [18], MSC.68(68) Annex 3 [17], MSC 302(87) [12] and MSC/Circ.862 [19].
Equipment for generation, transmission and reception of DSC designed according to the following equipment classes:
• Class A: includes all the facilities defined in annex 1 of Recommendation ITU-R M.493-15 [2] and complies
Performance Standards A.803(19) for VHF [15], A.804(19) for MF [16] and A.806(19) for MF/HF equipment
capable of voice and DSC [18].
• Class D: provides minimum facilities for VHF DSC distress, urgency and safety as well as routine calling and
reception as recommended by IMO MSC/Circ.803 [i.2] for non-SOLAS vessels participating in the GMDSS
and defined by Recommendation ITU-R M.493-15 [2].
• Class E: provides minimum facilities for MF and/or HF DSC distress, urgency and safety as well as routine
calling and reception as recommended by IMO MSC/Circ.803 [i.2] for non-SOLAS vessels participating in the
GMDSS and Recommendation ITU-R M.493-15 [2].
• Class H: provides minimum facilities for handheld VHF DSC distress, urgency and safety as well as routine
calling and reception as recommended by IMO MSC/Circ.803 [i.2] for non-SOLAS vessels participating in the
GMDSS and Recommendation ITU-R M.493-15 [2].
• Class M: provides minimum facilities for VHF Man Overboard devices as defined in Recommendation
ITU-R M.493-15 [2].
NOTE 1: Class A equipment may support the optional semi-automatic/automatic service in accordance with
Recommendations ITU-R M.689-3 [4], M.1082-1 [5] and M.493-15 [2], tables A1-4.10.1 and A1-4.10.2
and are encouraged to do so.
NOTE 2: Class D and Class E equipment may also support the optional semi-automatic/automatic service.
NOTE 3: Class D, Class E, Class H should provide a defined list of functions as a closed list for these classes of
equipment is the preferable approach to ensure safe and simple operation. Optional functions should be
avoided, with the intention to provide the same functionality of all equipment of one class.

  • Standard
    43 pages
    English language
    sale 15% off
  • Standard
    43 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Standard
    43 pages
    English language
    sale 15% off
  • Standard
    42 pages
    English language
    sale 15% off
  • Draft
    42 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 303 746 V1.1.1:2021(Main)
Maritime Location Systems - Radio transmitters and receivers for radio links in maritime radio location systems operating in the 9 GHz frequency band (X band)
ETSI EN 303 746 V1.1.1 (2021-04)

The present document specifies technical characteristics and methods of measurements for radiolocation equipment
with the following characteristics:
• intended to operate in maritime dynamic positioning systems functioning with full duplex links having a
duplex separation of 30 MHz;
• operating in the 9 GHz frequency band;
• with an integral antenna.

  • Standard
    21 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Standard
    21 pages
    English language
    sale 15% off
  • Standard
    20 pages
    English language
    sale 15% off
  • Standard
    20 pages
    English language
    sale 15% off
  • Draft
    20 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 301 925 V1.6.1:2021(Main)
Radiotelephone transmitters and receivers for the maritime mobile service operating in VHF bands - Technical characteristics and methods of measurement
ETSI EN 301 925 V1.6.1 (2020-12)

The present document specifies the minimum requirements for shipborne radio transmitters and receivers for fixed
installations operating in the VHF frequency bands between 156 MHz and 174 MHz used by the maritime mobile
service, using both 25 kHz and 12,5 kHz channels and capable of Radiotelephony and Digital Selective Calling
communications within the Global Maritime Distress and Safety System. The present document incorporates the
requirements of the relevant resolutions of the International Maritime Organization (IMO) and is primarily intended to
specify equipment suitable for fitting to ships subject to the SOLAS Convention [i.2] and complying with the Council
Directive 2014/90/EU [i.3] of 23 July 2014 on marine equipment (the European Marine Equipment Directive).
The present document does not address the testing of ancillary equipment on a stand-alone basis, i.e. separately from the
radio equipment with which it is to be used.

  • Standard
    60 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Standard
    60 pages
    English language
    sale 15% off
  • Standard
    60 pages
    English language
    sale 15% off
  • Standard
    60 pages
    English language
    sale 15% off
  • Draft
    60 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 300 338-3 V1.3.1:2020(Main)
Technical characteristics and methods of measurement for equipment for generation, transmission and reception of Digital Selective Calling (DSC) in the maritime MF, MF/HF and/or VHF mobile service - Part 3: Class D DSC
ETSI EN 300 338-3 V1.3.1 (2020-06)

The present document states the minimum requirements for general communication for shipborne fixed installations using
DSC - class D.
Class D DSC is intended be used in the Very High Frequency (VHF) band of the Maritime Mobile Service (MMS), for
distress, urgency and safety communication and general communications using telephony for subsequent
communications.
The present document is part 3 of a multi-part deliverable that covers the requirements to be fulfilled by equipment that
is either integrated with a transmitter and/or a receiver or equipment that is a stand-alone DSC terminal.
These requirements include the relevant provisions and the guidelines of the IMO as detailed in MSC/Circ.803 [i.1] for
non-SOLAS vessels participating in the GMDSS as well as Commission Decision of 12 August 2013
(2013/638/EU) [i.5].

  • Standard
    44 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Standard
    44 pages
    English language
    sale 15% off
  • Standard
    44 pages
    English language
    sale 15% off
  • Standard
    45 pages
    English language
    sale 15% off
  • Draft
    45 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 300 338-6 V1.2.1:2020(Main)
Technical characteristics and methods of measurement for equipment for generation, transmission and reception of Digital Selective Calling (DSC) in the maritime MF, MF/HF and/or VHF mobile service - Part 6: Class M DSC
ETSI EN 300 338-6 V1.2.1 (2020-06)

The present document states the minimum requirements for devices using Digital Selective Calling (DSC) Class M, for
Man Overboard (MOB). The present document defines the requirements for equipment that uses DSC alerting and
signalling in the maritime mobile bands and particularly the GMDSS distress and safety channels. Such equipment is
not intended to provide any subsequent communications or telephony facilities.
The present document is part 6 of a multi-part deliverable that covers the channel access rules and technical
requirements applicable to these devices.

  • Standard
    14 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Standard
    14 pages
    English language
    sale 15% off
  • Standard
    14 pages
    English language
    sale 15% off
  • Standard
    14 pages
    English language
    sale 15% off
  • Draft
    14 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 300 338-5 V1.3.1:2020(Main)
Technical characteristics and methods of measurement for equipment for generation, transmission and reception of Digital Selective Calling (DSC) in the maritime MF, MF/HF and/or VHF mobile service - Part 5: Handheld VHF Class H DSC
ETSI EN 300 338-5 V1.3.1 (2020-06)

The present document states the minimum requirements for general communication for handheld VHF radios using the
handheld class H DSC for shipborne use.
Class H DSC may be used in the Very High Frequency (VHF) Maritime Mobile Service (MMS), for distress, urgency
and safety communication and general communications using telephony for subsequent communications.
The present document is part 5 of a multi-part deliverable that covers the requirements to be fulfilled by equipment that
is integrated with a handheld transceiver.
These requirements include the relevant provisions and the guidelines of the IMO as detailed in MSC/Circ.803 [i.1] for
non-SOLAS vessels participating in the GMDSS.

  • Standard
    43 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Standard
    43 pages
    English language
    sale 15% off
  • Standard
    43 pages
    English language
    sale 15% off
  • Standard
    43 pages
    English language
    sale 15% off
  • Draft
    43 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 300 338-2 V1.5.1:2020(Main)
Technical characteristics and methods of measurement for equipment for generation, transmission and reception of Digital Selective Calling (DSC) in the maritime MF, MF/HF and/or VHF mobile service - Part 2: Class A DSC
ETSI EN 300 338-2 V1.5.1 (2020-06)

The present document states the minimum requirements for equipment to be used for generation, transmission and
reception of Class A Digital Selective Calling (DSC) for use on board ships.
DSC is intended to be used in the Medium Frequency (MF), High Frequency (HF) and Very High Frequency (VHF)
bands of the Maritime Mobile Service (MMS), for both distress, safety and general communications.
The present document is part 2 of a multi-part deliverable that covers the requirements to be fulfilled by equipment that
is either integrated with a transmitter and/or a receiver or equipment that is a stand-alone DSC terminal and has the
following class of DSC:
• Class A: includes all the facilities defined in annex 1 of Recommendation ITU-R M.493-15 [3] and complies
with the IMO Global Maritime Distress and Safety System (GMDSS) carriage requirements for MF/HF
installations and/or VHF installations.
These requirements include the relevant provisions of the ITU Radio Regulations [2] and Recommendation ITU-R
RM.493-15 [3], the International Convention for the Safety Of Life At Sea (SOLAS) [1], and the relevant resolutions of
the International Maritime Organization (IMO) [4].

  • Standard
    51 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Standard
    51 pages
    English language
    sale 15% off
  • Standard
    51 pages
    English language
    sale 15% off
  • Standard
    51 pages
    English language
    sale 15% off
  • Draft
    51 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 300 338-1 V1.5.1:2019(Main)
Technical characteristics and methods of measurement for equipment for generation, transmission and reception of Digital Selective Calling (DSC) in the maritime MF, MF/HF and/or VHF mobile service - Part 1: Common requirements
ETSI EN 300 338-1 V1.5.1 (2019-09)

The present document states the minimum requirements for equipment to be used for generation, transmission and
reception of Digital Selective Calling (DSC) for use on board ships.
DSC is intended to be used in the Medium Frequency (MF), High Frequency (HF) and Very High Frequency (VHF)
bands of the Maritime Mobile Service (MMS), for distress, urgency and safety communication and general
communications.
The present document is part 1 of a multi-part deliverable that covers the requirements to be fulfilled by:
• DSC equipment integrated with a transmitter and/or a receiver;
• DSC equipment not integrated with a transmitter and/or a receiver.
These requirements include the relevant provisions of the ITU Radio Regulations [i.17] and Recommendations ITU-R
M.493-15 [2], M.541-10 [3], M.689-3 [4] and M.1082-1 [5], the International Convention for the Safety Of Life At Sea
(SOLAS) [i.16], and the relevant resolutions of the International Maritime Organization (IMO).
Equipment for generation, transmission and reception of DSC designed according to the following equipment classes:
• Class A: includes all the facilities defined in annex 1 of Recommendation ITU-R M.493-15 [2] and complies
with the IMO Global Maritime Distress and Safety System (GMDSS) carriage requirements for MF/HF
installations and/or VHF installations.
• Class D: provides minimum facilities for VHF DSC distress, urgency and safety as well as routine calling and
reception as recommended by IMO MSC/Circ.803 [i.2] for non-SOLAS vessels participating in the GMDSS.
• Class E: provides minimum facilities for MF and/or HF DSC distress, urgency and safety as well as routine
calling and reception as recommended by IMO MSC/Circ.803 [i.2] for non-SOLAS vessels participating in the
GMDSS.
• Class H: provides minimum facilities for handheld VHF DSC distress, urgency and safety as well as routine
calling and reception as recommended by IMO MSC/Circ.803 [i.2] for non-SOLAS vessels participating in the
GMDSS.
• Class M: provides minimum facilities for VHF Man Overboard devices as defined in Recommendation ITU-R
M.493-15 [2].
NOTE 1: Class A equipment may support the optional semi-automatic/automatic service in accordance with
Recommendations ITU-R M.689-3 [4], M.1082-1 [5] and M.493-15 [2], tables A1-4.10.1 and A1-4.10.2
and are encouraged to do so.
NOTE 2: Class D and Class E equipment may also support the optional semi-automatic/automatic service.

  • Standard
    42 pages
    English language
    sale 15% off
  • Standard
    42 pages
    English language
    sale 15% off
  • Standard
    42 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Standard
    42 pages
    English language
    sale 15% off
  • Draft
    42 pages
    English language
    sale 10% off
    e-Library read for
    1 day