Powered hand-held hedge trimmers - Safety (ISO 10517:2019)

This document specifies safety requirements and measures for the verification of the design and
construction of hand-held, integrally-driven combustion engine hedge trimmers (hereafter referred to
as “hedge trimmers”) designed to be used by a single operator for trimming hedges and bushes while
utilizing one or more linear reciprocating cutter blades.
This document is also applicable to ”split-boom” type hedge trimmers and to multi-purpose machines
when configured as a hedge trimmer.
It establishes methods for the elimination or reduction of hazards arising from the use of the hedge
trimmers. In addition, it specifies the type of information to be provided by the manufacturer on safe
working practices.
This document deals with all significant hazards, hazardous situations and events relevant to powered
hand-held hedge trimmers when they are used as intended and under the conditions of misuse that are
reasonably foreseeable by the manufacturer (see Clause 4).
This document is not applicable to hedge trimmers with an engine displacement over 80 cm3, nor is it
applicable to hedge trimmers manufactured before the date of its publication.

Tragbare motorgetriebene Heckenscheren - Sicherheit (ISO 10517:2019)

Dieses Dokument legt sicherheitstechnische Anforderungen und Maßnahmen für die Überprüfung der Gestaltung und Konstruktion von tragbaren Heckenscheren mit Antrieb durch Verbrennungsmotor fest (nachfolgend „Hecken¬scheren“ genannt), die für die Anwendung durch einen einzelnen Benutzer zum Schneiden von Hecken und Büschen bestimmt und mit einem oder mehreren sich linear bewegenden Schneidmessern ausgestattet sind.
Dieses Dokument gilt auch für Heckenscheren mit teilbarem Schaft und Mehrzweckgeräte, wenn sie als Heckenschere konfiguriert sind.
Es legt Maßnahmen zur Vermeidung oder Verminderung der sich aus dem Gebrauch von Heckenscheren ergebenden Gefährdungen fest. Außerdem spezifiziert es die Art der Informationen über sicheres Arbeiten, die vom Hersteller zur Verfügung zu stellen sind.
Dieses Dokument behandelt alle signifikanten Gefährdungen, Gefährdungssituationen und  ereignisse, die bei bestimmungsgemäßer Verwendung und bei durch den Hersteller vernünftigerweise vorhersehbarer Fehlanwendung für tragbare motorbetriebene Heckenscheren relevant sind (siehe Abschnitt 4).
Dieses Dokument gilt nicht für Heckenscheren mit einem Hubraum über 80 cm3 und auch nicht für Heckenscheren, die vor dem Datum dieser Veröffentlichung hergestellt worden sind.

Taille-haies portatifs à moteur - Sécurité (ISO 10517:2019)

Le présent document spécifie les exigences de sécurité et les mesures relatives à leur vérification pour la conception et la construction des taille-haies portatifs à moteur thermique intégré, désignés ci-après par «taille-haies», conçus pour être utilisés par un seul opérateur pour tailler les haies et les buissons, et comportant une ou plusieurs lames de coupe à mouvement linéaire alternatif.
Le présent document s'applique également aux taille-haies de type à «perche fractionnée» et aux machines à usage universel lorsqu'elles sont configurées en taille-haies.
Il définit des méthodes permettant d'éliminer ou de réduire les phénomènes dangereux résultant de l'utilisation des taille-haies. En outre, il spécifie le type d'informations à fournir par le fabricant à propos des méthodes de travail sûres.
Le présent document traite tous les phénomènes dangereux importants, les situations dangereuses et les événements associés aux taille-haies portatifs à moteur lorsqu'ils sont utilisés pour l'usage prévu et dans les conditions de mauvaise utilisation raisonnablement prévisibles par le fabricant (voir l'Article 4).
Le présent document ne s'applique pas aux taille-haies équipés d'un moteur de cylindrée supérieure à 80 cm3, ni aux taille-haies fabriqués avant la date de sa publication.

Prenosni motorni obrezovalniki žive meje - Varnost (ISO 10517:2019)

Ta dokument določa varnostne zahteve in ukrepe za preverjanje zasnove in izdelave prenosnih motornih obrezovalnikov žive meje (v nadaljevanju »obrezovalniki žive meje«), ki so namenjeni za enega samega upravljavca za obrezovanje žive meje in grmovja z uporabo enega ali več linearnih povratnih rezil.
Ta dokument se uporablja tudi za obrezovalnike žive meje z ločljivim drogom in za večnamenske stroje, če so konfigurirani kot obrezovalniki žive meje.
Določa metode za odpravo ali zmanjšanje nevarnosti, ki izhajajo iz uporabe obrezovalnikov
žive meje. Poleg tega določa vrsto informacij, ki jih mora predložiti proizvajalec v zvezi z varnimi
delovnimi postopki.
Ta dokument obravnava vsa večja tveganja, nevarne okoliščine in nevarne dogodke v zvezi s prenosnimi motornimi obrezovalniki žive meje, kadar se uporabljajo v skladu s predvidenim namenom in pod pogoji pričakovane nepravilne uporabe, ki jih določa proizvajalec (glej točko 4).
Ne uporablja se za obrezovalnike žive meje s prostornino motorja, večjo od 80 cm3, in obrezovalnike žive meje, izdelane pred objavo tega standarda.

General Information

Status
Published
Public Enquiry End Date
25-Oct-2017
Publication Date
18-Mar-2019
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
07-Mar-2019
Due Date
12-May-2019
Completion Date
19-Mar-2019

Relations

Buy Standard

Standard
EN ISO 10517:2019 - BARVE
English language
43 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 10517:2019
01-maj-2019
1DGRPHãþD
SIST EN ISO 10517:2009
SIST EN ISO 10517:2009/A1:2014
Prenosni motorni obrezovalniki žive meje - Varnost (ISO 10517:2019)
Powered hand-held hedge trimmers - Safety (ISO 10517:2019)
Tragbare motorgetriebene Heckenscheren - Sicherheit (ISO 10517:2019)
Taille-haies portatifs à moteur - Sécurité (ISO 10517:2019)
Ta slovenski standard je istoveten z: EN ISO 10517:2019
ICS:
65.060.70 Vrtnarska oprema Horticultural equipment
SIST EN ISO 10517:2019 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 10517:2019

---------------------- Page: 2 ----------------------

SIST EN ISO 10517:2019


EN ISO 10517
EUROPEAN STANDARD

NORME EUROPÉENNE

February 2019
EUROPÄISCHE NORM
ICS 65.060.70 Supersedes EN ISO 10517:2009, EN ISO
10517:2009/A1:2003
English Version

Powered hand-held hedge trimmers - Safety (ISO
10517:2019)
Taille-haies portatifs à moteur - Sécurité (ISO Tragbare motorgetriebene Heckenscheren - Sicherheit
10517:2019) (ISO 10517:2019)
This European Standard was approved by CEN on 26 November 2018.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
C OM I TÉ EUROPÉEN DE NORMALISATIO N

EUROPÄISCHES KOMITEE FÜR NORMUN G

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2019 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 10517:2019 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN ISO 10517:2019
EN ISO 10517:2019 (E)
Contents Page
European foreword . 3
Annex ZA (informative) Relationship between this European Standard and the Essential
Requirements of EU Directive 2006/42/EC . 4

2

---------------------- Page: 4 ----------------------

SIST EN ISO 10517:2019
EN ISO 10517:2019 (E)
European foreword
This document (EN ISO 10517:2019) has been prepared by Technical Committee ISO/TC 23 "Tractors
and machinery for agriculture and forestry" in collaboration with Technical Committee CEN/TC 144
“Tractors and machinery for agriculture and forestry” the secretariat of which is held by AFNOR.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by August 2019, and conflicting national standards shall
be withdrawn at the latest by August 2019.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 10517:2009 and EN ISO 10517:2009/A1:2013.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of EU Directive(s).
For the relationship with EU Directive(s) see informative Annex ZA, which is an integral part of this
document.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
Endorsement notice
The text of ISO 10517:2019 has been approved by CEN as EN ISO 10517:2019 without any modification.

3

---------------------- Page: 5 ----------------------

SIST EN ISO 10517:2019
EN ISO 10517:2019 (E)
Annex ZA
(informative)

Relationship between this European Standard and the Essential
Requirements of EU Directive 2006/42/EC
This European Standard has been prepared under Commission’s standardization request "M/396
mandate to CEN and CENELEC for standardization in the field of machinery" to provide one voluntary
means of conforming to Essential Requirements of Directive 2006/42/EC of the European Parliament
and of the Council of 17 May 2006 on machinery, and amending Directive 95/16/EC (recast).
Once this standard is cited in the Official Journal of the European Union under that Directive,
compliance with the normative clauses of this standard given in Table ZA.1 confers, within the limits of
the scope of this standard, a presumption of conformity with the corresponding Essential
Requirements of that Directive and associated EFTA regulations.
Table ZA.1 — Correspondence between this European Standard and EU Directive 2006/42/EC
Essential requirements of EU Clause(s)/subclause(s) Remarks/Notes
Directive 2006/42/EC of this EN
Within the limits of the scope all relevant All normative clauses For relation of normative clauses of
essential requirements are covered this standard to significant
hazards/relevant essential
requirements of 2006/42/EC see clause
4 "List of significant hazards“ of this
standard in combination with annex D
“Examples of significant hazards,
hazardous situations, hazardous events
and their relation to the Essential
Requirements of the Machinery
Directive 2006/42/EC” of CEN Guide
414
(https:// boss.cen.eu/ref/CEN_414.pdf).

WARNING 1 - Presumption of conformity stays valid only as long as a reference to this European
Standard is maintained in the list published in the Official Journal of the European Union. Users of this
standard should consult frequently the latest list published in the Official Journal of the European
Union.
WARNING 2 - Other Union legislation may be applicable to the product(s) falling within the scope of this
standard.

4

---------------------- Page: 6 ----------------------

SIST EN ISO 10517:2019
INTERNATIONAL ISO
STANDARD 10517
Third edition
2019-02
Powered hand-held hedge
trimmers — Safety
Taille-haies portatifs à moteur — Sécurité
Reference number
ISO 10517:2019(E)
©
ISO 2019

---------------------- Page: 7 ----------------------

SIST EN ISO 10517:2019
ISO 10517:2019(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2019
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2019 – All rights reserved

---------------------- Page: 8 ----------------------

SIST EN ISO 10517:2019
ISO 10517:2019(E)

Contents Page
Foreword .v
Introduction .vi
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 2
4 List of significant hazards . 5
5 Safety requirements and/or verification of safety measures . 7
5.1 General . 7
5.2 Handles and cutting device . 7
5.2.1 Handles . 7
5.2.2 Hand protection . 8
5.2.3 Handle strength .10
5.2.4 Cutting device and blunt extensions .11
5.2.5 Shoulder harness requirements .15
5.2.6 Holding moment .15
5.2.7 Blade stopping time .18
5.2.8 Cutting device cover .20
5.2.9 Cutting device accessories .20
5.3 Starting and idling .20
5.4 Controls .20
5.4.1 Marking .20
5.4.2 Throttle control .20
5.4.3 Engine stop .21
5.5 Power driven parts protection .21
5.6 Heat protection .21
5.6.1 General.21
5.6.2 Test equipment, test conditions and test method .21
5.6.3 Test acceptance .22
5.7 Fuel tank .22
5.8 Engine exhaust .22
5.9 Electrical requirements of ignition system .23
5.9.1 General.23
5.9.2 Ignition circuit .23
5.9.3 Test method .23
5.9.4 Test acceptance .23
5.10 Vibration .23
5.10.1 Reduction by design and protective measures .23
5.10.2 Reduction by information .24
5.10.3 Vibration measurement .24
5.11 Noise .24
5.11.1 Reduction by design and by information .24
5.11.2 Noise emission measurement .24
6 Information for use .24
6.1 Instructions for use .24
6.2 Marking .25
6.3 Warnings .26
6.4 Test of labels .26
6.4.1 Preparation of test specimens and control specimens .26
6.4.2 Wipe resistance test .27
6.4.3 Adhesion test . . .27
Annex A (informative) Safety instructions .28
© ISO 2019 – All rights reserved iii

---------------------- Page: 9 ----------------------

SIST EN ISO 10517:2019
ISO 10517:2019(E)

Annex B (informative) Examples of safety signs, symbols and pictorials .31
Bibliography .33
iv © ISO 2019 – All rights reserved

---------------------- Page: 10 ----------------------

SIST EN ISO 10517:2019
ISO 10517:2019(E)

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the following
URL: www .iso .org/iso/foreword .html.
This document was prepared by Technical Committee ISO/TC 23, Tractors and machinery for agriculture
and forestry, Subcommittee SC 13, Powered lawn and garden equipment.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www .iso .org/members .html.
This third edition cancels and replaces the second edition (ISO 10517:2009), which has been technically
revised. It also incorporates the Amendment ISO 10517:2009/Amd 1:2013. The main changes compared
to the previous edition are as follows:
— the noise measurement procedure has been removed from the body of the document and has been
replaced with the reference to ISO 22868;
— the vibration measurement procedure has been removed from the body of the document and has
been replaced with the reference to ISO 22867;
— handle strength requirement has been added;
— extended-reach hedge trimmers have been better implemented in the body of the document;
— a test for the labels has been added;
— several text changes have been made for better understanding.
© ISO 2019 – All rights reserved v

---------------------- Page: 11 ----------------------

SIST EN ISO 10517:2019
ISO 10517:2019(E)

Introduction
This document is a type-C standard as stated in ISO 12100.
This document is of relevance, in particular, for the following stakeholder groups representing the
market players with regard to machinery safety:
— machine manufacturers (small, medium and large enterprises);
— health and safety bodies (regulators, accident prevention organisations, market surveillance, etc.).
Others can be affected by the level of machinery safety achieved with the means of the document by the
above-mentioned stakeholder groups:
— machine users/employers (small, medium and large enterprises);
— machine users/employees (e.g. trade unions, organizations for people with special needs);
— service providers, e.g. for maintenance (small, medium and large enterprises);
— consumers (in case of machinery intended for use by consumers).
The above-mentioned stakeholder groups have been given the possibility to participate in the drafting
process of this document.
The machinery concerned and the extent to which hazards, hazardous situations or hazardous events
are covered are indicated in the scope of this document.
When requirements of this type-C standard are different from those which are stated in the type-A or
type-B standards, the requirements of this type-C standard take precedence over the requirements of
the other standards for machines that have been designed and built according to the requirements of
this type-C standard.
vi © ISO 2019 – All rights reserved

---------------------- Page: 12 ----------------------

SIST EN ISO 10517:2019
INTERNATIONAL STANDARD ISO 10517:2019(E)
Powered hand-held hedge trimmers — Safety
1 Scope
This document specifies safety requirements and measures for the verification of the design and
construction of hand-held, integrally-driven combustion engine hedge trimmers (hereafter referred to
as “hedge trimmers”) designed to be used by a single operator for trimming hedges and bushes while
utilizing one or more linear reciprocating cutter blades.
This document is also applicable to ”split-boom” type hedge trimmers and to multi-purpose machines
when configured as a hedge trimmer.
It establishes methods for the elimination or reduction of hazards arising from the use of the hedge
trimmers. In addition, it specifies the type of information to be provided by the manufacturer on safe
working practices.
This document deals with all significant hazards, hazardous situations and events relevant to powered
hand-held hedge trimmers when they are used as intended and under the conditions of misuse that are
reasonably foreseeable by the manufacturer (see Clause 4).
3
This document is not applicable to hedge trimmers with an engine displacement over 80 cm , nor is it
applicable to hedge trimmers manufactured before the date of its publication.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
ISO 3767-1, Tractors, machinery for agriculture and forestry, powered lawn and garden equipment —
Symbols for operator controls and other displays — Part 1: Common symbols
ISO 3767-3, Tractors, machinery for agriculture and forestry, powered lawn and garden equipment —
Symbols for operator controls and other displays — Part 3: Symbols for powered lawn and garden equipment
ISO 3767-4, Tractors, machinery for agriculture and forestry, powered lawn and garden equipment —
Symbols for operator controls and other displays — Part 4: Symbols for forestry machinery
ISO 3864-2, Graphical symbols — Safety colours and safety signs — Part 2: Design principles for product
safety labels
ISO 7010, Graphical symbols — Safety colours and safety signs — Registered safety signs
ISO 11684, Tractors, machinery for agriculture and forestry, powered lawn and garden equipment — Safety
signs and hazard pictorials — General principles
ISO 12100:2010, Safety of machinery — General principles for design — Risk assessment and risk reduction
ISO 13857:2008, Safety of machinery — Safety distances to prevent hazard zones being reached by upper
and lower limbs
ISO 22867, Forestry and gardening machinery — Vibration test code for portable hand-held machines with
internal combustion engine — Vibration at the handles
ISO 22868, Forestry and gardening machinery — Noise test code for portable hand-held machines with
internal combustion engine — Engineering method (Grade 2 accuracy)
© ISO 2019 – All rights reserved 1

---------------------- Page: 13 ----------------------

SIST EN ISO 10517:2019
ISO 10517:2019(E)

IEC 61032:1997, Protection of person and equipment by enclosures — Probes for verification
3 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
— ISO Online browsing platform: available at https: //www .iso .org/obp
— IEC Electropedia: available at http: //www .electropedia .org/
3.1
hedge trimmer
machine fitted with reciprocating blades made of metal, intended to cut and form hedges, bushes and
similar vegetation
3.2
cutting device
part of the assembly consisting of cutter blade and shear plate, or of the cutter blades together with any
supporting part, which performs the cutting action and that can be single- or double-sided
Note 1 to entry: See Figure 2.
3.3
cutter blade
part of the cutting device having blade teeth which cut by a shearing action either against other blade
teeth or against a shear plate
Note 1 to entry: See Figure 2.
3.4
blade tooth
part of the cutter blade which is sharpened to perform the shearing action
Note 1 to entry: See Figure 2.
3.5
cutting length
effective cutting length of the cutting device measured from the inside edge of the first blade tooth or
shear plate tooth to the inside edge of the last blade tooth or shear plate tooth
Note 1 to entry: See Figure 3.
Note 2 to entry: Where both blades move, the measurements are taken when the first and last teeth are
furthest apart.
3.6
front handle
handle located at or towards the cutting device
Note 1 to entry: See Figure 1.
3.7
rear handle
handle located furthest from the cutting device
Note 1 to entry: See Figure 1.
3.8
throttle lock
device for temporarily setting the throttle in a partially open position to aid starting
2 © ISO 2019 – All rights reserved

---------------------- Page: 14 ----------------------

SIST EN ISO 10517:2019
ISO 10517:2019(E)

3.9
throttle control lock-out
device which prevents the unintentional activation of the throttle trigger unless the operator releases it
3.10
throttle control
blade control
device activated by the operator's hand or finger for controlling the cutter blade movement
Note 1 to entry: This can require a single or a two-stage operation depending on the application.
3.11
blunt extension
extending blunt part of the cutting device or an extending part of an unsharpened plate fitted to the
cutting device to prevent contact with the moving cutter blade
3.12
adjustable handle
handle whose position can be modified either by movement or by rotation
3.13
drive shaft
shaft used to transmit power from the engine to the cutting device
3.14
drive shaft tube
tube which contains the drive shaft and connects the engine to the cutting device
Note 1 to entry: It can be fixed, extendable or telescoping in length. For ease of storage and transportation, the
drive shaft tube can be detachable.
3.15
split-boom
design feature which permits the separation of the drive shaft tube for ease of storage and transportation
3.16
dry weight
weight of the unit with empty fuel/oil tank(s) and without cutting device cover
Dimensions in millimetres
a) Single-sided hedge trimmer
© ISO 2019 – All rights reserved 3

---------------------- Page: 15 ----------------------

SIST EN ISO 10517:2019
ISO 10517:2019(E)

b) Double-sided hedge trimmer
c) Extended-reach hedge trimmer
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.