SIST EN IEC 62841-3-9:2020/A11:2020

SLOVENSKI STANDARD
SIST EN IEC 62841-3-9:2020/A11:2020
01-oktober-2020
Elektromotorna ročna orodja, prenosna orodja ter stroji za trato in vrt - Varnost - 3-
9. del: Posebne zahteve za prenosne zajeralne žage - Dopolnilo A11
Electric motor-operated hand-held tools, transportable tools and lawn and garden
machinery - Safety - Part 3-9: Particular requirements for transportable mitre saws
Elektrische motorbetriebene handgeführte Werkzeuge, transportable Werkzeuge und
Rasen- und Gartenmaschinen - Sicherheit - Teil 3-9: Besondere Anforderungen für
transportable Gehrungskappsägen
Outils électroportatifs à moteur, outils portables et machines pour jardins et pelouses -
Sécurité - Partie 3-9: Exigences particulières pour les scies à onglets transportables
Ta slovenski standard je istoveten z: EN IEC 62841-3-9:2020/A11:2020
ICS:
25.080.60 Strojne žage Sawing machines
25.140.20 Električna orodja Electric tools
SIST EN IEC 62841-3-9:2020/A11:2020 en,fr
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN IEC 62841-3-9:2020/A11:2020

---------------------- Page: 2 ----------------------
SIST EN IEC 62841-3-9:2020/A11:2020


EUROPEAN STANDARD EN IEC 62841-3-9:2020/A11

NORME EUROPÉENNE

EUROPÄISCHE NORM
June 2020
ICS 25.140.20

English Version
Electric motor-operated hand-held tools, transportable tools and
lawn and garden machinery - Safety - Part 3-9: Particular
requirements for transportable mitre saws
Outils électroportatifs à moteur, outils portables et machines Elektrische motorbetriebene handgeführte Werkzeuge,
pour jardins et pelouses - Sécurité - Partie 3-9: Exigences transportable Werkzeuge und Rasen- und
particulières pour les scies à onglets transportables Gartenmaschinen - Sicherheit - Teil 3-9: Besondere
Anforderungen für transportable Gehrungskappsägen
This amendment A11 modifies the European Standard EN IEC 62841-3-9:2020; it was approved by CENELEC on 2020-04-20. CENELEC
members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this amendment the
status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This amendment exists in three official versions (English, French, German). A version in any other language made by translation under the
responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the same status as
the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.


European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2020 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
 Ref. No. EN IEC 62841-3-9:2020/A11:2020 E

---------------------- Page: 3 ----------------------
SIST EN IEC 62841-3-9:2020/A11:2020
EN IEC 62841-3-9:2020/A11:2020 (E)
European foreword
This document (EN IEC 62841-3-9:2020/A11:2020) was prepared by CLC/TC 116 "Safety of motor-
operated electric tools".
The following dates are fixed:

• latest date by which this document has (dop) 2021-04-20
to be implemented at national level by
publication of an identical national
standard or by endorsement
• latest date by which the national (dow) 2024-04-20
standards conflicting with this document
have to be withdrawn
This document modifies by common modifications EN IEC 62841-3-9:2020, which consists of the text of
IEC 62841-3-9, Ed.2.0 prepared by IEC/TC 116 “Safety of motor-operated electric tools”.
This series is divided into four parts:
Part 1: General requirements which are common to most hand-held electric motor operated tools
(for the purpose of this standard referred to simply as tools) which could come within the
scope of this standard;
Part 2, 3 or 4: Requirements for particular types of tools which either supplement or modify the
requirements given in Part 1 to account for the particular hazards and characteristics of
these specific tools.
This Part 3-9 is to be used in conjunction with EN 62841-1:2015.
This Part 3-9 supplements or modifies the corresponding clauses in EN 62841-1:2015, so as to convert it
into the European Standard: Particular requirements for transportable mitre saws.
Where a particular subclause of Part 1 is not mentioned in this Part 3-9, that subclause applies as far as
relevant. When this standard states "addition", "modification" or "replacement", the relevant text in Part 1
is to be adapted accordingly.
The following print types are used:
- requirements; in roman type
- test specifications: in italic type;
- notes: in smaller roman type.
The terms defined in Clause 3 are printed in bold typeface.
Subclauses, notes, tables and figures which are additional to those in Part 1 are numbered starting
from 101.
Clauses, subclauses, notes, tables, figures and annexes which are additional to those in
IEC 62841-3-9:2020 are prefixed “Z”.
This European Standard follows the overall requirements of EN ISO 12100.
This document has been prepared under a mandate given to CENELEC by the European Commission
and the European Free Trade Association and supports essential requirements of EU Directive(s).
For the relationship with EU Directive(s), see informative Annex ZZ, which is an integral part of this
document.
Compliance with the clauses of Part 1 together with this Part 3-9 provides one means of conforming with
the essential health and safety requirements of the Directive concerned.
2

---------------------- Page: 4 ----------------------
SIST EN IEC 62841-3-9:2020/A11:2020
EN IEC 62841-3-9:2020/A11:2020 (E)
1 Modification to Clause 1, “Scope”
Add after the first paragraph:
“This document applies to transportable mitre saws having a mass of:
– maximum 25 kg for tools capable of being lifted by hand by one person;
– maximum 50 kg for tools capable of being lifted by hand by two persons.
This document does not apply to stationary mitre saws.
NOTE Z101 EN 1870-3 gives requirements for stationary mitre saws and mitre saws with a mass greater than indicated above.”

Add after the last paragraph:
“This document covers all significant hazards, hazardous situations or hazardous events relevant for
machines covered by this document.
NOTE Z102 Essential requirements not mentioned in Table ZZ.1 are deemed to be not applicable, because the corresponding
hazards are either not relevant for machines covered by this standard or do not require specific action by the designer.”

2 Modification to Clause 2, “Normative references”
Add the following normative reference:
EN 847-1:2017, Tools for woodworking - Safety requirements - Part 1: Milling tools, circular saw blades
3 Modification to Clause 8, “Marking and instructions”
Replace the last sentence in 8.3 with the following:
“This symbol needs not be in accordance with the colour requirements of ISO 3864-2:2016.”

Add the following new item to 8.14.2 a):
“Z101) Instruction to use only saw blades recommended by the manufacturer, which conform to
EN 847-1:2017, if intended for wood and analogous materials.”

Add the following after 8.14.2 c):
“8.14.2 Za) Replacement of items 3, 4 and 5 with the following:
3) The following information:
− that the declared noise emission value(s) have been measured in accordance with a
standard test method and may be used for comparing one tool with another;
− that the declared noise emission value(s) may also be used in a preliminary assessment of
exposure.
3

---------------------- Page: 5 ----------------------
SIST EN IEC 62841-3-9:2020/A11:2020
EN IEC 62841-3-9:2020/A11:2020 (E)
4) A warning:
− that the noise emissions during actual use of the power tool can differ from the declared
values depending on the ways in which the tool is used especially what kind of workpiece
is processed; and
− of the need to identify safety measures to protect the operator that are based on an
estimation of exposure in the actual conditions of use (taking account of all parts of the
operating cycle such as the times when the tool is switched off and when it is running idle
in addition to the trigger time).”

4 Modification to Clause 19, “Mechanical hazards”
Replace the first paragraph of 19.102 with the following:
“When released, the saw unit shall automatically return to its rest position. The return device of the saw
unit, the lower guard and of the wo
...