EN ISO 25178-72:2017/A1:2020

SLOVENSKI STANDARD
SIST EN ISO 25178-72:2017/A1:2020
01-december-2020
Specifikacija geometrijskih veličin izdelka (GPS) - Tekstura površine: ravna - 72.
del: XML-format datoteke x3p - Dopolnilo A1 (ISO 25178-72:2017/Amd 1:2020)
Geometrical product specifications (GPS) - Surface texture: Areal - Part 72: XML file
format x3p - Amendment 1 (ISO 25178-72:2017/Amd 1:2020)
Geometrische Produktspezifikation (GPS) - Oberflächenbeschaffenheit: Flächenhaft -
Teil 72: XML-Dateiformat x3p - Änderung 1 (ISO 25178-72:2017/Amd 1:2020)
Spécification géométrique des produits (GPS) - État de surface: Surfacique - Partie 72:
Format de fichier XML x3p - Amendement 1 (ISO 25178-72:2017/Amd 1:2020)
Ta slovenski standard je istoveten z: EN ISO 25178-72:2017/A1:2020
ICS:
17.040.20 Lastnosti površin Properties of surfaces
17.040.40 Specifikacija geometrijskih Geometrical Product
veličin izdelka (GPS) Specification (GPS)
SIST EN ISO 25178-72:2017/A1:2020 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN ISO 25178-72:2017/A1:2020

---------------------- Page: 2 ----------------------
SIST EN ISO 25178-72:2017/A1:2020


EN ISO 25178-
EUROPEAN STANDARD
72:2017/A1
NORME EUROPÉENNE

EUROPÄISCHE NORM

September 2020
ICS 17.040.20
English Version

Geometrical product specifications (GPS) - Surface texture:
Areal - Part 72: XML file format x3p - Amendment 1 (ISO
25178-72:2017/Amd 1:2020)
Spécification géométrique des produits (GPS) - État de Geometrische Produktspezifikationen (GPS) -
surface: Surfacique - Partie 72: Format de fichier XML Oberflächenbeschaffenheit: Flächenhaft - Teil 72: XML-
x3p - Amendement 1 (ISO 25178-72:2017/Amd Dateiformat x3p - Änderung 1 (ISO 25178-
1:2020) 72:2017/Amd 1:2020)
This amendment A1 modifies the European Standard EN ISO 25178-72:2017; it was approved by CEN on 25 August 2020.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of
this amendment into the relevant national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.

This amendment exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2020 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 25178-72:2017/A1:2020 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------
SIST EN ISO 25178-72:2017/A1:2020
EN ISO 25178-72:2017/A1:2020 (E)
Contents Page
European foreword . 3

2

---------------------- Page: 4 ----------------------
SIST EN ISO 25178-72:2017/A1:2020
EN ISO 25178-72:2017/A1:2020 (E)
European foreword
This document (EN ISO 25178-72:2017/A1:2020) has been prepared by Technical Committee ISO/TC
213 "Dimensional and geometrical product specifications and verification" in collaboration with
Technical Committee CEN/TC 290 “Dimensional and geometrical product specification and verification”
the secretariat of which is held by AFNOR.
This Amendment to the European Standard EN ISO 25178-72:2017 shall be given the status of a
national standard, either by publication of an identical text or by endorsement, at the latest by March
2021, and conflicting national standards shall be withdrawn at the latest by March 2021.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia,
...