EN 10051:2010
(Main)Continuously hot-rolled strip and plate/sheet cut from wide strip of non-alloy and alloy steels - Tolerances on dimensions and shape
Continuously hot-rolled strip and plate/sheet cut from wide strip of non-alloy and alloy steels - Tolerances on dimensions and shape
This European Standard specifies tolerances on dimensions and shape for continuously hot-rolled uncoated plate/sheet and strip with a maximum width of 2 200 mm of non-alloy and alloy steels in accordance with Table 1 (see also Annex A). This European Standard also applies to hot-rolled strip for cold rolling.
This European Standard does not apply to stainless steels and not to hot-rolled strip rolled in widths w < 600 mm (see EN 10048).
Kontinuierlich warmgewalztes Band und Blech abgelängt aus Warmbreitband aus unlegierten und legierten Stählen - Grenzabmaße und Formtoleranzen
Diese Europäische Norm legt die Grenzabmaße und Formtoleranzen für kontinuierlich warmgewalztes Blech und Band ohne Überzug in Breiten bis höchstens 2 200 mm aus unlegierten und legierten Stählen nach Tabelle 1 (siehe auch Anhang A), fest. Diese Europäische Norm gilt auch für warmgewalztes Band, das zum Kaltwalzen bestimmt ist.
Diese Europäische Norm gilt nicht für nichtrostende Stähle und nicht für warmgewalztes Band in Walzbreiten w 600 mm (siehe EN 10048).
Bandes laminées à chaud en continu, bandes et tôles issues de larges bandes laminées à chaud en aciers alliés et non alliés - Tolérances sur les dimensions et la forme
La présente Norme européenne spécifie les tolérances sur les dimensions et la forme des bandes et tôles non revêtues, laminées à chaud en continu, d’une largeur maximale de 2 200 mm, en aciers alliés et non alliés, conformément au Tableau 1 (voir également l’Annexe A). La présente Norme européenne s’applique également aux bandes laminées à chaud destinées au laminage à froid.
La présente Norme européenne ne s’applique ni aux aciers inoxydables ni aux bandes laminées à chaud, en largeur < 600 mm [EN 10048].
Kontinuirno vroče valjane pločevine in trakovi iz legiranih in nelegiranih jekel brez prevleke - Tolerance mer in oblik
Ta evropski standard določa tolerance mer in oblik za kontinuirno vroče valjane pločevine in trakove z največjo debelino 2200 mm iz nelegiranih in legiranih jekel brez prevleke v skladu s preglednico 1 (glej tudi dodatek A). Ta evropski standard velja tudi za vroče valjane trakove za hladno valjanje.
TA evropski standard ne velja za nerjavna jekla in vroče valjane trakove, valjane v širinah š < 600 mm (glej EN 10048).
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Kontinuierlich warmgewalztes Band und Blech abgelängt aus Warmbreitband aus unlegierten und legierten Stählen - Grenzabmaße und FormtoleranzenBandes laminées à chaud en continu, bandes et tôles issues de larges bandes laminées à chaud en aciers alliés et non alliés - Tolérances sur les dimensions et la formeContinuously hot-rolled strip and plate/sheet cut from wide strip of non-alloy and alloy steels - Tolerances on dimensions and shape77.140.50SROL]GHONLFlat steel products and semi-productsICS:Ta slovenski standard je istoveten z:EN 10051:2010SIST EN 10051:2012en,fr,de01-januar-2012SIST EN 10051:2012SLOVENSKI
STANDARDSIST EN 10051:19981DGRPHãþD
SIST EN 10051:2012
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 10051
November 2010 ICS 77.140.50 Supersedes EN 10051:1991 + A1:1997English Version
Continuously hot-rolled strip and plate/sheet cut from wide strip of non-alloy and alloy steels - Tolerances on dimensions and shape
Bandes laminées à chaud en continu, bandes et tôles issues de larges bandes laminées à chaud en aciers alliés et non alliés - Tolérances sur les dimensions et la forme
Kontinuierlich warmgewalztes Band und Blech abgelängt aus Warmbreitband aus unlegierten und legierten Stählen -Grenzabmaße und Formtoleranzen This European Standard was approved by CEN on 23 October 2010.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2010 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 10051:2010: ESIST EN 10051:2012
EN 10051:2010 (E) 2 Contents Page Foreword .31 Scope .42 Normative references .43 Terms and definitions .44 Information to be supplied by the purchaser .54.1 General .54.2 Options .54.3 Designation .55 Form of supply .56 Tolerances for sheet/plate .66.1 Thickness .66.2 Length .86.3 Width .86.4 Flatness .96.5 Edge camber .
...
SLOVENSKI STANDARD
oSIST prEN 10051:2009
01-julij-2009
.RQWLQXLUQRYURþHYDOMDQHSORþHYLQHLQWUDNRYLL]OHJLUDQLKLQQHOHJLUDQLKMHNHOEUH]
SUHYOHN7ROHUDQFHPHULQREOLN
Hot-rolled strip and plate/sheet cut from wide strip of non-alloy and alloy steels -
Tolerances on dimensions and shape
Warmgewalztes Band und Blech abgelängt aus Warmbreitband aus unlegierten und
legierten Stählen - Grenzabmaße und Formtoleranzen
Bandes et tôles issues de larges bandes laminées à chaud en aciers alliés et non alliés -
Tolérances sur les dimensions et la forme
Ta slovenski standard je istoveten z: prEN 10051
ICS:
77.140.50 3ORãþDWLMHNOHQLL]GHONLLQ Flat steel products and semi-
SROL]GHONL products
oSIST prEN 10051:2009 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
oSIST prEN 10051:2009
---------------------- Page: 2 ----------------------
oSIST prEN 10051:2009
EUROPEAN STANDARD
DRAFT
prEN 10051
NORME EUROPÉENNE
EUROPÄISCHE NORM
April 2009
ICS 77.140.50 Will supersede EN 10051:1991 + A1:1997
English Version
Hot-rolled strip and plate/sheet cut from wide strip of non-alloy
and alloy steels - Tolerances on dimensions and shape
Bandes et tôles issues de larges bandes laminées à chaud Warmgewalztes Band und Blech abgelängt aus
en aciers alliés et non alliés - Tolérances sur les Warmbreitband aus unlegierten und legierten Stählen -
dimensions et la forme Grenzabmaße und Formtoleranzen
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee ECISS/TC 12.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations which
stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other language
made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the
same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are aware and to
provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2009 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 10051:2009: E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
oSIST prEN 10051:2009
prEN 10051:2009 (E)
Contents Page
Foreword .3
1 Scope .4
2 Normative references .4
3 Terms and definitions .4
4 Information to be supplied by the purchaser .5
4.1 General .5
4.2 Options .5
4.3 Example .5
5 Delivery condition .5
6 Tolerances for sheet/plate .6
6.1 Thickness .
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.