CEN/TR 17081:2018
(Main)Design of fastenings for use in concrete - Plastic design of fastenings with headed and post-installed fasteners
Design of fastenings for use in concrete - Plastic design of fastenings with headed and post-installed fasteners
This Technical Report gives provisions for design of ultimate limit states in addition to EN 1992 4 for headed and post-installed fasteners excluding concrete screws, which only transmit static actions to the concrete, when the loads on individual fasteners are determined according to plastic analysis of the joint where only equilibrium conditions but no compatibility conditions are considered. Fatigue, impact and seismic loads are not covered.
Bemessung der Verankerung von Befestigungen in Beton - Traglastverfahren für Befestigungsmittel von Kopfbolzen und Dübel
Conception-calcul des fixations pour utilisation dans le béton - Conception plastique des fixations à boulons à tête et à chevilles de fixation
Projektiranje pritrjevanja za uporabo v betonu - Projektiranje pritrjevanja z veznimi sredstvi z glavo in naknadno vgrajenimi veznimi sredstvi po teoriji plastičnosti
To tehnično poročilo zajema določbe za projektiranje skrajnih mejnih stanj dodatno k standardu EN 1992 4 za vezna sredstva z glavo in naknadno vgrajena vezna sredstva razen betonskih vijakov, ki zgolj prenašajo statična dejanja v beton, kadar so obremenitve posameznih veznih elementov določene v skladu s plastično analizo spoja, kjer so upoštevani samo uravnoteženi pogoji, ne pa tudi pogoji združljivosti. Utrujanje, sunki in seizmične obremenitve niso obravnavani.
General Information
Standards Content (Sample)
SLOVENSKI STANDARD
SIST-TP CEN/TR 17081:2018
01-december-2018
3URMHNWLUDQMHSULWUMHYDQMD]DXSRUDERYEHWRQX3URMHNWLUDQMHSULWUMHYDQMD]YH]QLPL
VUHGVWYL]JODYRLQQDNQDGQRYJUDMHQLPLYH]QLPLVUHGVWYLSRWHRULMLSODVWLþQRVWL
Design of fastenings for use in concrete - Plastic design of fastenings with headed and
post-installed fasteners
Bemessung der Verankerung von Befestigungen in Beton - Traglastverfahren für
Befestigungsmittel von Kopfbolzen und Dübel
Conception-calcul des fixations pour utilisation dans le béton - Conception plastique des
fixations à boulons à tête et à chevilles de fixation
Ta slovenski standard je istoveten z: CEN/TR 17081:2018
ICS:
21.060.01 Vezni elementi na splošno Fasteners in general
91.080.40 Betonske konstrukcije Concrete structures
SIST-TP CEN/TR 17081:2018 en,fr
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST-TP CEN/TR 17081:2018
---------------------- Page: 2 ----------------------
SIST-TP CEN/TR 17081:2018
CEN/TR 17081
TECHNICAL REPORT
RAPPORT TECHNIQUE
September 2018
TECHNISCHER BERICHT
ICS 21.060.01; 91.080.40
English Version
Design of fastenings for use in concrete - Plastic design of
fastenings with headed and post-installed fasteners
Bemessung der Verankerung von Befestigungen in
Beton - Traglastverfahren für Befestigungsmittel von
Kopfbolzen und Dübel
This Technical Report was approved by CEN on 9 April 2017. It has been drawn up by the Technical Committee CEN/TC 250.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2018 CEN All rights of exploitation in any form and by any means reserved Ref. No. CEN/TR 17081:2018 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST-TP CEN/TR 17081:2018
CEN/TR 17081:2018 (E)
Contents Page
European foreword . 3
Introduction . 4
1 Scope . 5
2 Normative references . 5
3 Terms, definitions and symbols . 5
4 Field of application . 5
4.1 General . 5
4.2 Conditions for ductile behaviour . 5
5 Loads on fastenings . 8
5.1 General . 8
5.2 Compression forces . 8
5.3 Location of the compressive force . 8
5.4 Assumption for the tension side of the fastening . 10
5.5 Limitation on location of fasteners in tension . 11
5.6 Distribution of shear forces. 11
6 Design of fastenings.
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.