EN ISO 14571:2022
(Main)Metallic coatings on non-metallic basis materials - Measurement of coating thickness - Micro-resistivity method (ISO 14571:2020)
Metallic coatings on non-metallic basis materials - Measurement of coating thickness - Micro-resistivity method (ISO 14571:2020)
This document specifies a method for non-destructive measurements of the thickness of conductive coatings on non-conductive base materials. This method is based on the principle of the sheet resistivity measurement and is applicable to any conductive coatings and layers of metal and semiconductor materials. In general, the probe has to be adjusted to the conductivity and the thickness of the respective application. However, this document focuses on metallic coatings on non-conductive base materials (e.g. copper on plastic substrates, printed circuit boards).
This method is also applicable to thickness measurements of conductive coatings on conductive base materials, if the resistivity of the coating and the base material is significantly different. However, this case is not considered in this document.
Metallische Überzüge auf nichtmetallischen Grundwerkstoffen - Schichtdickenmessung - Mikro-Widerstand-Verfahren (ISO 14571:2020)
Dieses Dokument legt ein Verfahren für zerstörungsfreie Messungen der Dicke von elektrisch leitenden Überzügen auf nichtleitenden Grundwerkstoffen fest. Dieses Verfahren beruht auf dem Prinzip der Flächenwiderstandsmessung und ist auf alle leitfähigen Überzügen und Schichten aus metallischen und halbleitenden Materialien anwendbar. Generell muss die Sonde an die Leitfähigkeit und die Schichtdicke des jeweiligen Einsatzfalls angepasst sein. Dieses Dokument befasst sich jedoch ausschließlich mit metallischen Überzügen auf nichtleitenden Grundwerkstoffen (z. B. Kupfer auf Kunststoffsubstraten, Leiterplatten).
Dieses Verfahren ist ebenfalls für die Schichtdickenmessung von leitfähigen Überzügen auf leitfähigen Grundmaterialien anwendbar, wenn sich der spezifische Widerstand vom Grundmaterial von dem des Überzuges unterscheidet. Dieser Fall wird in diesem Dokument nicht berücksichtigt.
Revêtements métalliques sur matériaux non-métalliques - Mesurage de l'épaisseur des revêtements - Méthode utilisant la micro-résistivité (ISO 14571:2020)
Le présent document spécifie une méthode de mesurages non destructifs de l’épaisseur des revêtements conducteurs sur des matériaux de base non conducteurs. Cette méthode repose sur le principe du mesurage de la résistivité d’une plaque et elle est applicable à tous les revêtements conducteurs et couches de métaux et de matériaux semi-conducteurs. En général, le palpeur doit être ajusté à la conductivité et à l’épaisseur de l’application correspondante. Toutefois, le présent document est centré sur les revêtements métalliques appliqués sur des matériaux de base non conducteurs (par exemple, cuivre sur substrats en plastique, cartes de circuits imprimés).
Cette méthode est aussi applicable aux mesurages d’épaisseur des revêtements conducteurs sur des matériaux de base conducteurs, si la résistivité du revêtement et celle du matériau de base sont nettement différentes. Cependant, ce cas n’est pas traité dans le présent document.
Kovinske prevleke na materialih z nekovinsko osnovo - Merjenje debeline prevleke - Metoda mikroupornosti (ISO 14571:2020)
Ta dokument določa metodo za neporušitvene meritve debeline prevodnih prevlek na neprevodnih osnovnih materialih. Ta metoda temelji na principu merjenja upornosti pločevine in je uporabna za vse prevodne prevleke in plasti kovinskih in polprevodniških materialov. Na splošno je treba sondo prilagoditi prevodnosti in debelini posameznega nanosa. Vendar ta dokument se osredotoča na kovinske prevleke na neprevodnih osnovnih materialih (npr. baker na plastičnih podlagah, tiskana vezja).
Ta metoda je uporabna tudi za meritve debeline prevodnih prevlek na prevodnih osnovnih materialih, če se upornost prevleke in osnovnega materiala bistveno razlikujeta. Ta primer ni vključen v ta dokument.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 14571:2023
01-januar-2023
Nadomešča:
SIST EN 14571:2005
Kovinske prevleke na materialih z nekovinsko osnovo - Merjenje debeline prevleke
- Metoda mikroupornosti (ISO 14571:2020)
Metallic coatings on non-metallic basis materials - Measurement of coating thickness -
Micro-resistivity method (ISO 14571:2020)
Metallische Überzüge auf nichtmetallischen Grundwerkstoffen - Schichtdickenmessung -
Mikro-Widerstand-Verfahren (ISO 14571:2020)
Revêtements métalliques sur matériaux non-métalliques - Mesurage de l'épaisseur des
revêtements - Méthode utilisant la micro-résistivité (ISO 14571:2020)
Ta slovenski standard je istoveten z: EN ISO 14571:2022
ICS:
17.040.20 Lastnosti površin Properties of surfaces
25.220.40 Kovinske prevleke Metallic coatings
SIST EN ISO 14571:2023 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 14571:2023
---------------------- Page: 2 ----------------------
SIST EN ISO 14571:2023
EN ISO 14571
EUROPEAN STANDARD
NORME EUROPÉENNE
November 2022
EUROPÄISCHE NORM
ICS 25.220.40 Supersedes EN 14571:2005
English Version
Metallic coatings on non-metallic basis materials -
Measurement of coating thickness - Micro-resistivity
method (ISO 14571:2020)
Revêtements métalliques sur matériaux non- Metallische Überzüge auf nichtmetallischen
métalliques - Mesurage de l'épaisseur des revêtements Grundwerkstoffen - Schichtdickenmessung - Mikro-
- Méthode utilisant la micro-résistivité (ISO Widerstand-Verfahren (ISO 14571:2020)
14571:2020)
This European Standard was approved by CEN on 30 October 2022.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2022 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 14571:2022 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 14571:2023
EN ISO 14571:2022 (E)
Contents Page
European foreword . 3
2
---------------------- Page: 4 ----------------------
SIST EN ISO 14571:2023
EN ISO 14571:2022 (E)
European foreword
The text of ISO 14571:2020 has been prepared by Technical Committee ISO/TC 107 "Metallic and other
inorganic coatings” of the International Organization for Standardization (ISO) and has been taken over
as EN ISO 14571:2022 by Technical Committee CEN/TC 262 “Metallic and other inorganic coatings,
including for corrosion protection and corrosion testing of metals and alloys” the secretariat of which is
held by BSI.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by May 2023, and conflicting national standards shall be
withdrawn at the latest by May 2023.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 14571:2005.
Any feedback and questions on this document should be directed to the users’ national standards body.
A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Nethe
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.