CEN/TS 15427-2-3:2023
(Main)Railway applications - Wheel/rail friction management - Part 2-3: Properties and Characteristics - Adhesion materials
Railway applications - Wheel/rail friction management - Part 2-3: Properties and Characteristics - Adhesion materials
This document specifies the requirements of adhesion materials intended to be applied to the interface between the wheel tread and the rail crown (active interface). It can be applied either directly or indirectly to the wheel tread or rail.
It outlines the information required for most approval procedures, the method of testing and routine control/monitoring of the material.
This document does not deal with Top of Rail materials. For Top of Rail materials see CEN/TS 15427 2 2:2023.
Bahnanwendungen - Reibungsmanagement zwischen Rad und Schiene - Teil 2-3: Eigenschaften und Merkmale - Kraftschlusserhöhende Materialien
Dieses Dokument legt die Anforderungen an kraftschlusserhöhende Materialien für die Anwendung auf der Kontaktfläche zwischen Radlauffläche und Fahrfläche der Schiene (aktive Kontaktfläche) fest. Diese können direkt oder indirekt auf die Radlauffläche oder die Schiene angewendet werden.
Es beschreibt die erforderlichen Informationen für die meisten Genehmigungsverfahren, das Prüfverfahren und die regelmäßige Kontrolle/Überwachung des Materials.
Dieses Dokument behandelt keine Kraftschlussmodifikatoren. Zu Kraftschlussmodifikatoren siehe CEN/TS 15427 2 2:2023.
Applications ferroviaires - Gestion des frottements roue/rail - Partie 2-3 : Propriétés et caractéristiques - Matériaux pour restauration d'adhérence
Le présent document spécifie les exigences applicables aux matériaux pour restauration d'adhérence destinés à être appliqués sur l'interface entre la bande de roulement de la roue et la tête de rail (interface active). Ils peuvent être appliqués directement ou indirectement, sur la bande de roulement ou sur le rail.
Le présent document précise également les informations nécessaires à la plupart des procédures de validation, la méthode d'essai et les tâches de contrôle/surveillance de routine du matériau.
Le présent document ne traite pas des lubrifiants de tête de rail. Pour les lubrifiants de tête de rail, se reporter à la CEN/TS 15427 2 2:2023.
Železniške naprave - Trenje na stiku kolo-tirnica - 2-3. del: Lastnosti in karakteristike - Lepilni materiali
Ta dokument določa zahteve lepilnih materialov, namenjenih za uporabo na vmesniku med kolesnim obročem in zgornjim robom tirnice (aktivni vmesnik). Uporabljati ga je mogoče posredno ali neposredno za kolesni obroč oziroma tirnico.
Podaja informacije, ki se zahtevajo pri večini postopkov odobritve, preskusno metodo in rutinsko kontrolo/spremljanje materiala.
Dokument ne obravnava materialov za zgornjo površino tirnic. Za tovrstne materiale glej standard FprCEN/TS 15427-2-2:2023.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST-TS CEN/TS 15427-2-3:2023
01-december-2023
Nadomešča:
SIST-TS CEN/TS 15427-2-3:2021
Železniške naprave - Trenje na stiku kolo-tirnica - 2-3. del: Lastnosti in
karakteristike - Lepilni materiali
Railway applications - Wheel/rail friction management - Part 2-3: Properties and
Characteristics - Adhesion materials
Bahnanwendungen - Reibungsmanagement zwischen Rad und Schiene - Teil 2-3:
Eigenschaften und Merkmale - Kraftschlusserhöhende Materialien
Applications ferroviaires - Gestion des frottements roue/rail - Partie 2-3 : Propriétés et
caractéristiques - Matériaux pour restauration d'adhérence
Ta slovenski standard je istoveten z: CEN/TS 15427-2-3:2023
ICS:
45.040 Materiali in deli za železniško Materials and components
tehniko for railway engineering
SIST-TS CEN/TS 15427-2-3:2023 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST-TS CEN/TS 15427-2-3:2023
---------------------- Page: 2 ----------------------
SIST-TS CEN/TS 15427-2-3:2023
CEN/TS 15427-2-3
TECHNICAL SPECIFICATION
SPÉCIFICATION TECHNIQUE
October 2023
TECHNISCHE SPEZIFIKATION
ICS 45.040 Supersedes CEN/TS 15427-2-3:2021
English Version
Railway applications - Wheel/rail friction management -
Part 2-3: Properties and Characteristics - Adhesion
materials
Applications ferroviaires - Gestion du frottement Bahnanwendungen - Reibungsmanagement zwischen
roue/rail - Parte 2-3: Propriétés et Caractéristiques - Rad und Schiene - Teil 2-3: Eigenschaften und
Matériau d'Adhésion Merkmale - Kraftschlusserhöhende Materialien
This Technical Specification (CEN/TS) was approved by CEN on 23 July 2023 for provisional application.
The period of validity of this CEN/TS is limited initially to three years. After two years the members of CEN will be requested to
submit their comments, particularly on the question whether the CEN/TS can be converted into a European Standard.
CEN members are required to announce the existence of this CEN/TS in the same way as for an EN and to make the CEN/TS
available promptly at national level in an appropriate form. It is permissible to keep conflicting national standards in force (in
parallel to the CEN/TS) until the final decision about the possible conversion of the CEN/TS into an EN is reached.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2023 CEN All rights of exploitation in any form and by any means reserved Ref. No. CEN/TS 15427-2-3:2023 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST-TS CEN/TS 15427-2-3:2023
CEN/TS 15427-2-3:2023 (E)
Contents Page
European foreword . 3
Introduction . 4
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 5
4 Adhesion material requirements . 6
5 Technical specification and approval of product . 7
5.1 Introduction . 7
5.2 Product specification . 7
5.3 Technical file . 7
6 Control and monitoring of product . 8
6.1 Manufacturing process . 8
6.2 Composition of material .
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.