iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CEN

EN 15882-5:2021

(Main)

Extended application of results from fire resistance tests for service installations - Part 5: Combined penetration seals

Extended application of results from fire resistance tests for service installations - Part 5: Combined penetration seals

The purpose of this document is to provide the principles and guidance for the preparation of extended application documents for combined penetration seals where the systems were tested in accordance with (EN 1366-3 and EN 1366-1) or (EN 1366-3 and EN 1366-2). The field of the extended application document is additional to the direct field of application given within EN 1366-1, EN 1366-2 and EN 1366-3 and can be applied on a number of tests from each standard, which provide the relevant information for the formulation of an extended application.
This EXAP is intended to allow the penetration sealing of more than one service (e.g. cables, pipes, conduits) and four-sided fire resisting ducts (ventilation ducts) or fire dampers in the same penetration.
This EXAP is not used for extended applications in accordance with EN 1366-8, EN 1366-10 and/or EN 1366-12 (this will be dealt with in the next revision of the standard).

Erweiterter Anwendungsbereich der Ergebnisse aus Feuerwiderstandsprüfungen für Installationen - Teil 5: Erweiterte Kombiabschottungen

Zweck dieses Dokuments ist die Bereitstellung von Grundsätzen und Anleitungen für die Erstellung von Dokumenten zur erweiterten Anwendung von erweiterten Kombiabschottungen, die nach (EN 1366 3 und EN 1366 1) bzw. (EN 1366 3 und EN 1366 2) geprüft wurden. Das Dokument zum erweiterten Anwendungsbereich gilt zusätzlich zu dem in EN 1366 1, EN 1366 2 und EN 1366 3 angegebenen direkten Anwendungsbereich und kann für mehrere Prüfungen aus jeder Norm angewendet werden, die die relevanten Informationen für die Formulierung einer erweiterten Anwendung liefert.
Dieses EXAP-Dokument (en: extended application) dient dazu, die Abschottung mehrerer Leitungen (z. B. Kabel, Rohrleitungen, Elektro-Installationsrohre (EIR)) und vierseitig feuerwiderstandsfähiger Leitungen (Lüftungsleitungen) oder Brandschutzklappen in derselben Durchführung zu ermöglichen.
Es dient nicht dazu, einen erweiterten Anwendungsbereich von Prüfergebnissen nach EN 1366 8, EN 1366 10 und/oder EN 1366 12 zu ermöglichen (dies ist Gegenstand der nächsten Überarbeitung der Norm).

Application étendue des résultats des essais de résistance au feu des installations de service - Partie 5 : Calfeutrements de trémie combinés

Le présent document a pour objectif de fournir des principes et des recommandations pour l'élaboration de documents d'application étendue relatifs aux systèmes de calfeutrements de trémie combinés ayant été soumis à essai conformément à l'(EN 1366-3 et à l'EN 1366-1) ou à l'(EN 1366-3 et à l'EN 1366-2). Par rapport au domaine d'application direct décrit dans l'EN 1366-1, l'EN 1366-2 et l'EN 1366-3, le domaine d'application étendue du présent document est complémentaire et peut s'appliquer à plusieurs essais de chacune de ces normes, lesquels fournissent les informations pertinentes permettant de formuler une application étendue.
Cet EXAP a pour objectif de permettre le calfeutrement de plusieurs traversants (par exemple : câbles, tuyaux, gaines) et de conduits à quatre côtés résistant au feu (conduits de ventilation) ou de clapets résistant au feu dans la même traversée.
Cet EXAP n'est pas utilisé pour des applications étendues conformément à l'EN 1366-8, l'EN 1366-10 et/ou l'EN 1366-12 (cela sera traité dans la prochaine révision de la norme).

Razširjena uporaba rezultatov preskusov požarne odpornosti servisnih inštalacij - 5. del: Kombinirane tesnitve prebojev

General Information

Status
Published
Publication Date
12-Oct-2021
Withdrawal Date
29-Apr-2022
ICS
13.220.99 - Other standards related to protection against fire
Technical Committee
CEN/TC 127 - Fire safety in buildings
Drafting Committee
CEN/TC 127/WG 2 - Services
Current Stage
6060 - Definitive text made available (DAV) - Publishing
Start Date
13-Oct-2021
Due Date
26-Nov-2021
Completion Date
13-Oct-2021
Directive
305/2011 - Regulation (eu) No 305/2011 of the European Parliament and of the Council of 9 march 2011 laying down harmonised conditions for the marketing of construction products and repealing council directive 89/106/eec
Mandate
M/117 - Horizontal complement to the mandates to CEN/CENELEC concerning the execution of standardization work for the valuation of construction products and elements in respect of their resistance to fire
Ref Project
SIST EN 15882-5:2021 - Extended application of results from fire resistance tests for service installations - Part 5: Combined penetration seals

Buy Standard

EN 15882-5:2021EN 15882-5:2021
PreviousNext
Standard
EN 15882-5:2021
English language
37 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 15882-5:2021
01-december-2021
Razširjena uporaba rezultatov preskusov požarne odpornosti servisnih inštalacij -
5. del: Kombinirane tesnitve prebojev
Extended application of results from fire resistance tests for service installations - Part 5:
Combined penetration seals
Erweiterter Anwendungsbereich der Ergebnisse aus Feuerwiderstandsprüfungen für
Installationen - Teil 5: Kombinierte Abschottungen
Application étendue des résultats des essais de résistance au feu des installations de
service - Partie 5 : Calfeutrements de trémie combinés
Ta slovenski standard je istoveten z: EN 15882-5:2021
ICS:
13.220.50 Požarna odpornost Fire-resistance of building
gradbenih materialov in materials and elements
elementov
SIST EN 15882-5:2021 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN 15882-5:2021

---------------------- Page: 2 ----------------------
SIST EN 15882-5:2021


EN 15882-5
EUROPEAN STANDARD

NORME EUROPÉENNE

October 2021
EUROPÄISCHE NORM
ICS 13.220.99
English Version

Extended application of results from fire resistance tests
for service installations - Part 5: Combined penetration
seals
Application étendue des résultats des essais de Erweiterter Anwendungsbereich der Ergebnisse aus
résistance au feu des installations de service - Partie 5 : Feuerwiderstandsprüfungen für Installationen - Teil 5:
Calfeutrements de trémie combinés Kombinierte Abschottungen
This European Standard was approved by CEN on 25 July 2021.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2021 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 15882-5:2021 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------
SIST EN 15882-5:2021
EN 15882-5:2021 (E)
Contents Page
European foreword . 3
1 Scope . 4
2 Normative references . 4
3 Terms and definitions . 5
4 Extended application principles . 5
5 Pre-conditions for extended application — Fire Resisting Ducts (ventilation ducts) . 6
5.1 Basic tests required . 6
5.2 Additional collaborative test requirements for the EXAP test with respect to fire
resisting ducts (ventilation ducts) . 7
6 Specific rules to be applied to combined penetration applications — Fire resisting
ducts . 15
6.1 General. 15
6.2 Service penetration field of extended application (permitted variations) . 16
7 Pre-conditions for extended application — Fire dampers .
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN
EN 15882-2:2022(Main)
Extended application of results from fire resistance tests for service installations - Part 2: Fire dampers
SIST EN 15882-2:2022

This document provides guidance and rules to notified bodies (for fire dampers) allowing them to produce/validate an extended field of application report for fire dampers based on testing undertaken in accordance with EN 1366 2. This document identifies the parameters that affect the fire resistance of fire dampers. It also identifies the factors that need to be considered when deciding whether, or by how much, the parameter can be extended when contemplating the fire resistance performance of an untested, or untestable variation in the construction.
This document explains the principles behind how a conclusion on the influence of specific parameters/constructional details relating to the relevant criteria (E, I, S) can be achieved.
This document does not cover dampers used for smoke control or non-mechanical fire barriers.
It is the intention that the application of this document makes it possible to identify which specifications to test to maximize the field of application. Some information on test programmes is given for guidance purposes.

  • Standard
    45 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 13381-2:2014(Main)
Test methods for determining the contribution to the fire resistance of structural members - Part 2: Vertical protective membranes
SIST EN 13381-2:2014

This European Standard specifies a test method for determining the ability of a vertical protective membrane, when used as a fire resistant barrier, to contribute to the fire resistance (loadbearing capacity R) of loadbearing vertical structural building members fabricated from steel, concrete, steel/concrete composites or timber. The method described is applicable to any type of vertical protective membrane, which can be associated with a separate bracing membrane.
The vertical protective membrane can be either separated from or attached to the structural building member and is self-supporting. This test method is applicable to vertical protective membranes where there is a gap and a cavity between the vertical protective membrane and the structural building member, otherwise alternative test methods prEN 13381-3, EN 13381-4, EN 13381-6 or prEN 13381-7 should be used as appropriate.
This test method and assessment is not applicable to the following:
a) all situations where the cavity is to be used as a service or ventilation shaft;
b) all situations where the vertical protective membrane acts as a bracing membrane.
This European Standard contains the fire test which specifies the tests which shall be carried out whereby the vertical protective membrane together with the structural member to be protected is exposed to the specified fire. The fire exposure, to the standard temperature/time curve given in EN 1363-1, is applied to the side which would be exposed in practice.
The test method makes provision, through specified optional additional procedures, for the collection of data which can be used as direct input to the calculation of fire resistance according to the processes given in EN 1992-1-2, EN 1993-1-2, EN 1994-1-2 and EN 1995-1-2.
This European Standard also contains the assessment which provides information relative to the analysis of the test data and gives guidance for the interpretation of the results of the fire test, in terms of loadbearing capacity criteria of the protected vertical structural member.
The results of the fire test and the assessment can be applied, with certain defined provisions, to vertical structural building members which can be beams, columns or a combination of both and / or which could form part of a separating element or partition.
The limits of applicability of the results of the assessment arising from the fire test are defined, together with permitted direct application of the results to different structures, membranes and fittings.
In special circumstances, where specified in national building regulations, there can be a need to subject the protection material to a smouldering curve. The test for this and the special circumstances for its use are detailed in Annex B.
Tests should be carried out without additional combustible materials in the cavity.

  • Standard
    35 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 15882-4:2012(Main)
Extended application of results from fire resistance tests for service installations - Part 4: Linear joint seals
SIST EN 15882-4:2012

This European standard specifies rules and prescribes the methodology for the preparation of extended application reports for linear joint sealing systems tested in accordance with EN 1366-4. The field of the extended application reports is additional to the direct field of application given in EN 1366-4. It may be applied to or based on a single test, or a number of tests, which provide the relevant information for the formulation of an extended application.
Mechanical metal seals are not part of the scope of this European standard.

  • Standard
    12 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
prEN 15882-2(Main)
Extended application of results from fire resistance tests for service installations - Part 2: Dampers
oSIST prEN 15882-2:2011

To provide guidance and rules to notified or accredited bodies (for Fire Dampers) to allow them to define the extended field of application for fire dampers. To identify the parameters that affects the fire resistance of dampers. In addition, to identify the factors that need to be considered when deciding whether, or by how much, the parameter can be extended when contemplating the fire resistance performance of an untested, or untestable variation in the construction.

  • Draft
    28 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 15882-2:2022(Main)
Extended application of results from fire resistance tests for service installations - Part 2: Fire dampers
SIST EN 15882-2:2022

This document provides guidance and rules to notified bodies (for fire dampers) allowing them to produce/validate an extended field of application report for fire dampers based on testing undertaken in accordance with EN 1366 2. This document identifies the parameters that affect the fire resistance of fire dampers. It also identifies the factors that need to be considered when deciding whether, or by how much, the parameter can be extended when contemplating the fire resistance performance of an untested, or untestable variation in the construction.
This document explains the principles behind how a conclusion on the influence of specific parameters/constructional details relating to the relevant criteria (E, I, S) can be achieved.
This document does not cover dampers used for smoke control or non-mechanical fire barriers.
It is the intention that the application of this document makes it possible to identify which specifications to test to maximize the field of application. Some information on test programmes is given for guidance purposes.

  • Standard
    45 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
CEN/TS 12101-11:2022(Main)
Smoke and heat control systems - Part 11: Horizontal flow powered ventilation systems for enclosed car parks
SIST-TS CEN/TS 12101-11:2022

This document gives minimum design, installation and commissioning requirements for powered smoke and heat control systems for enclosed car parks using horizontal flow powered ventilation, with or without sprinkler protection, on one or more levels, for cars and light commercial vehicles (max 3,5 t), to reach the design objectives outlined in this document .
This document is applicable for car parks with vehicles powered by petrol, diesel, electricity, CNG or LPG.
NOTE 1   For the purpose of this document for smoke ventilation systems, it is assumed that cars powered by electricity, CNG (compressed natural gas) or LPG (liquefied petroleum gas) will have similar HRR to vehicles powered by petrol or diesel.
NOTE 2   Cars powered by hydrogen are not covered by this document.
This document only covers traditional car parks that are with cars parked alongside each other, with common car access lanes. It does not cover other forms of car parking systems, such as stacking systems.
This document does not cover requirements for day‐to‐day ventilation.
Any other risks than fire from cars are not covered by this document.

  • Technical specification
    51 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 12101-6:2022(Main)
Smoke and heat control systems - Part 6: Specification for pressure differential systems - Kits
SIST EN 12101-6:2022

This document applies to pressure differential system kits and components, positioned on the market and intended to operate as part of a pressure differential system. The purpose of a pressure differential system is to prevent protected spaces from smoke spread by using pressure difference and airflow. This document specifies characteristics and test methods for components and kits for pressure differential systems to produce and control the required pressure differential and airflow between protected and unprotected space.

  • Standard
    65 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 12101-13:2022(Main)
Smoke and heat control systems - Part 13: Pressure differential systems (PDS) - Design and calculation methods, installation, acceptance testing, routine testing and maintenance
SIST EN 12101-13:2022

This document gives calculation methods, guidance and requirements for the design, installation, acceptance testing, routine testing and maintenance for pressure differential systems (PDS).
PDSs are designed to hold back smoke at a leaky physical barrier in a building, such as a door (either open or closed) or other similarly restricted openings and to keep tenable conditions in escape and access routes depending on the application.
It covers systems intended to protect means of escape e.g. staircases, corridors, lobbies, as well as systems intended to provide a protected firefighting space (bridgehead) for the fire services.
It provides details on the critical features and relevant procedures for the installation.
It describes the commissioning procedures and acceptance testing criteria required to confirm that the calculated design is achieved in the building.
This document gives rules, requirements and procedures to design PDS for buildings up to 60 m.
For buildings taller than 60 m the same requirements are given (e.g. Table 1), but additional methods of calculation and verification are necessary. Requirements for such methods and verification are given in Annex D, but the methods fall outside the scope of this document [e.g. Additional mathematical analysis and/or Computational Fluid Dynamics (CFD)].
Routine testing and maintenance requirements are also defined in this document.
In the absence of national requirements and under expected ambient and outside conditions, the requirements in Table 1 are fulfilled by the PDS.

  • Standard
    118 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 12101-2:2017(Main)
Smoke and heat control systems - Part 2: Natural smoke and heat exhaust ventilators
SIST EN 12101-2:2017

This European Standard applies to natural smoke and heat exhaust ventilators (NSHEV) operating as part of smoke and heat exhaust systems (NSHEVS), placed on the market. This standard specifies requirements and gives test methods for natural smoke and heat exhaust ventilators which are intended to be installed in smoke and heat control systems in buildings.

  • Standard
    88 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 16852:2016(Main)
Flame arresters - Performance requirements, test methods and limits for use (ISO 16852:2016)
SIST EN ISO 16852:2017

ISO 16852:2016 specifies the requirements for flame arresters that prevent flame transmission when explosive gas-air or vapour-air mixtures are present. It establishes uniform principles for the classification, basic construction and information for use, including the marking of flame arresters, and specifies test methods to verify the safety requirements and determine safe limits of use.
This International Standard is valid for pressures ranging from 80 kPa to 160 kPa and temperatures ranging from −20 °C to + 150 °C.
NOTE 1       For flame arresters with operational conditions inside the scope, but outside atmospheric conditions, see 7.4.
NOTE 2       In designing and testing flame arresters for operation under conditions other than those specified above, this International Standard can be used as a guide. However, additional testing related specifically to the intended conditions of use is advisable. This is particularly important when high temperatures and pressures are applied. The test mixtures might need to be modified in these cases.
NOTE 3       An additional standard IMO MSC/Circ. 677 for maritime application from IMO (International Maritime Organization) exists.
ISO 16852:2016 is not applicable to the following:
-      external safety-related measurement and control equipment that might be required to keep the operational conditions within the established safe limits;
NOTE 4       Integrated measurement and control equipment, such as integrated temperature and flame sensors as well as parts which, for example, intentionally melt (retaining pin), burn away (weather hoods) or bend (bimetallic strips), is within the scope of this International Standard.
-      flame arresters used for explosive mixtures of vapours and gases, which tend to self-decompose (e.g. acetylene) or which are chemically unstable;
-      flame arresters used for carbon disulphide, due to its special properties;
-      flame arresters whose intended use is for mixtures other than gas-air or vapour-air mixtures (e.g. higher oxygen-nitrogen ratio, chlorine as oxidant, etc.);
-      flame arrester test procedures for internal-combustion compression ignition engines;
-      fast acting valves, extinguishing systems and other explosion isolating systems.

  • Standard
    62 pages
    English language
    sale 10% off
    e-Library read for
    1 day