iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CEN

FprCEN ISO/TR 22391-7

(Main)

Plastics piping systems for hot and cold water installations - Polyethylene of raised temperature resistance (PE-RT) - Part 7: Guidance for the assessment of conformity (ISO/DTR 22391-7:2010)

Plastics piping systems for hot and cold water installations - Polyethylene of raised temperature resistance (PE-RT) - Part 7: Guidance for the assessment of conformity (ISO/DTR 22391-7:2010)

This Technical REPORT gives guidance for the assessment of conformity to be included in the manufacturer's quality plan as part of his quality system. This Technical Specification includes: a) requirements for materials, components, joints and assemblies given in the applicable Part(s) of ISO/FDIS 22391; b) requirements for the manufacturer's quality system; NOTE 1 It is recommended that the quality system conforms to ISO 9001:2000[2]. c) definitions and procedures to be applied if third party certification is involved. NOTE 2 If third party certification is involved, it is recommended that the certification body is accredited to EN 45011[3] or EN 45012[4], as applicable. In conjunction with the other Parts of ISO/FDIS 22391 (see Foreword), this Part is applicable to Polyethylene of raised temperature resistance (PE-RT) piping systems intended to be used for hot and cold water installations within buildings for the conveyance of water, whether or not intended for human consumption (domestic systems), under design pressures and temperatures appropriate to the class of application (see Table 1 of ISO/FDIS 22391-1:(2008)).

Kunststoff-Rohrleitungssysteme für die Warm- und Kaltwasserinstallation - Polyethylen erhöhter Temperaturbeständigkeit (PE-RT) - Teil 7: Empfehlungen für die Beurteilung der Konformität (ISO/DTR 22391-7:2010)

Dieser Teil von ISO 22391 enthält Empfehlungen für die Beurteilung der Konformität von Erzeugnissen und Bauteilkombinationen entsprechend des/der zutreffenden Teile(s) von ISO 22391 die als Teil des Qualitäts-managementsystems im Qualitätssicherungsplan des Herstellers und für die Einführung von Verfahren der Drittstellenzertifizierung vorgesehen sind.
Zusammen mit den übrigen Teilen gilt dieser Teil von ISO 22391 für Rohrleitungssysteme, die in der Warm- und Kaltwasserinstallation innerhalb von Gebäuden für den Transport von Trink- oder Brauchwasser (Hausinstallation) sowie für Heizungsanlagen unter Berücksichtigung des betreffenden zulässigen Betriebsdruckes und der für die jeweilige Anwendungsklasse geltenden Temperaturen eingesetzt werden.

Systèmes de canalisations en plastique pour les installations d'eau chaude et froide - Polyéthylène de meilleure résistance à la température (PE-RT) - Partie 7: Directives pour l'évaluation de la conformité (ISO/DTR 22391-7:2010)

Cevni sistemi iz polimernih materialov za napeljave z vročo in hladno vodo - Polietilen s povečano temperaturno odpornostjo (PE-RT) - 7. del: Navodilo za ugotavljanje skladnosti (ISO/DTR 22391-7:2010)

General Information

Status
Not Published
Publication Date
04-Oct-2010
ICS
23.040.01 - Pipeline components and pipelines in general
91.140.60 - Water supply systems
93.025 - External water conveyance systems
Technical Committee
CEN/TC 155 - Plastics piping systems and ducting systems
Drafting Committee
CEN/TC 155/WG 16 - Systems for hot and cold water applications
Current Stage
5098 - Decision to abandon - Formal Approval
Start Date
06-Jul-2010
Completion Date
06-Jul-2010
Ref Project
kSIST-TP FprCEN ISO/TR 22391-7:2010 - Plastics piping systems for hot and cold water installations - Polyethylene of raised temperature resistance (PE-RT) - Part 7: Guidance for the assessment of conformity (ISO/DTR 22391-7:2010)

Buy Standard

kTP FprCEN ISO/TR 22391-7:2010kTP FprCEN ISO/TR 22391-7:2010
PreviousNext
Draft
kTP FprCEN ISO/TR 22391-7:2010
English language
25 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
kSIST-TP FprCEN ISO/TR 22391-7:2010
01-september-2010
&HYQLVLVWHPLL]SROLPHUQLKPDWHULDORY]DQDSHOMDYH]YURþRLQKODGQRYRGR
3ROLHWLOHQVSRYHþDQRWHPSHUDWXUQRRGSRUQRVWMR 3(57 GHO1DYRGLOR]D
XJRWDYOMDQMHVNODGQRVWL ,62'75
Plastics piping systems for hot and cold water installations - Polyethylene of raised
temperature resistance (PE-RT) - Part 7: Guidance for the assessment of conformity
(ISO/DTR 22391-7:2010)
Kunststoff-Rohrleitungssysteme für die Warm- und Kaltwasserinstallation - Polyethylen
erhöhter Temperaturbeständigkeit (PE-RT) - Teil 7: Empfehlungen für die Beurteilung
der Konformität (ISO/DTR 22391-7:2010)
Systèmes de canalisations en plastique pour les installations d'eau chaude et froide -
Polyéthylène de meilleure résistance à la température (PE-RT) - Partie 7: Directives pour
l'évaluation de la conformité (ISO/DTR 22391-7:2010)
Ta slovenski standard je istoveten z: FprCEN ISO/TR 22391-7
ICS:
23.040.01 Deli cevovodov in cevovodi Pipeline components and
na splošno pipelines in general
91.140.60 Sistemi za oskrbo z vodo Water supply systems
kSIST-TP FprCEN ISO/TR 22391-7:2010 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

kSIST-TP FprCEN ISO/TR 22391-7:2010

---------------------- Page: 2 ----------------------

kSIST-TP FprCEN ISO/TR 22391-7:2010


TECHNICAL REPORT
FINAL DRAFT
FprCEN ISO/TR 22391-7
RAPPORT TECHNIQUE

TECHNISCHER BERICHT

June 2010
ICS 93.025; 91.140.60; 23.040.01
English Version
Plastics piping systems for hot and cold water installations -
Polyethylene of raised temperature resistance (PE-RT) - Part 7:
Guidance for the assessment of conformity (ISO/DTR 22391-
7:2010)
Systèmes de canalisations en plastique pour les Kunststoff-Rohrleitungssysteme für die Warm- und
installations d'eau chaude et froide - Polyéthylène de Kaltwasserinstallation - Polyethylen erhöhter
meilleure résistance à la température (PE-RT) - Partie 7: Temperaturbeständigkeit (PE-RT) - Teil 7: Empfehlungen
Directives pour l'évaluation de la conformité (ISO/DTR für die Beurteilung der Konformität (ISO/DTR 22391-
22391-7:2010) 7:2010)


This draft Technical Report is submitted to CEN members for Technical Committee Approval. It has been drawn up by the Technical
Committee CEN/TC 155.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.



Warning : This document is not a Technical Report. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a Technical Report.


EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2010 CEN All rights of exploitation in any form and by any means reserved Ref. No. FprCEN ISO/TR 22391-7:2010: E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

kSIST-TP FprCEN ISO/TR 22391-7:2010
FprCEN ISO/TR 22391-7:2010 (E)
Contents Page
Foreword .3

2

---------------------- Page: 4 ----------------------

kSIST-TP FprCEN ISO/TR 22391-7:2010
FprCEN ISO/TR 22391-7:2010 (E)
Foreword
This document (FprCEN ISO/TR 22391-7:2010) has been prepared by Technical Committee ISO/TC 138
"Plastics pipes, fittings and valves for the transport of fluids" in collaboration Technical Committee
CEN/TC 155 “Plastics piping systems and ducting systems” the secretariat of which is held by NEN.
This document is currently submitted to the parallel TC Approval.
3

---------------------- Page: 5 ----------------------

kSIST-TP FprCEN ISO/TR 22391-7:2010

---------------------- Page: 6 ----------------------

kSIST-TP FprCEN ISO/TR 22391-7:2010

TECHNICAL ISO/TR
REPORT 22391-7
First edition
2010-##-##

Plastics piping systems for hot and cold
water installations — Polyethylene of
raised temperature resistance (PE-RT) —
Part 7:
Guidance for the assessment
of conformity
Systèmes de canalisations en plastique pour les installations d'eau
chaude et froide — Polyéthylène de meilleure résistance à la
température (PE-RT) —
Partie 7: Directives pour l'évaluation de la conformité



PROOF/ÉPREUVE
Reference number
ISO/TR 22391-7:2010(E)
©
ISO 2010

---------------------- Page: 7 ----------------------

kSIST-TP FprCEN ISO/TR 22391-7:2010
ISO/TR 22391-7:2010(E)
PDF disclaimer
This PDF file may c
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN
EN ISO 22391-5:2009/A1:2020(Amendment)
Plastics piping systems for hot and cold water installations - Polyethylene of raised temperature resistance (PE-RT) - Part 5: Fitness for purpose of the system - Amendment 1 (ISO 22391-5:2009/Amd 1:2020, Corrected version 2021-03)
SIST EN ISO 22391-5:2010/A1:2021
  • Amendment
    9 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Amendment
    9 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
CEN ISO/TS 22391-7:2018(Main)
Plastics piping systems for hot and cold water installations - Polyethylene of raised temperature resistance (PE-RT) - Part 7: Guidance for the assessment of conformity (ISO/TS 22391-7:2018)
SIST-TS CEN ISO/TS 22391-7:2019

This part of ISO 22391 gives guidance for the assessment of conformity of materials, products, and assemblies in accordance with the applicable part(s) of ISO 22391 intended to be included in the manufacturer’s quality plan as part of the quality management system and for the establishment of certification procedures.
In conjunction with the other parts of ISO 22391 (see Foreword), this Technical Specification is applicable to polyethylene of raised temperature resistance (PE-RT) piping systems intended to be used for hot and cold water installations within buildings for the conveyance of water, whether or not intended for human consumption (domestic systems) and for heating systems, under design pressures and temperatures appropriate to the class of application (see Table 1 of ISO 22391:2009).

  • Technical specification
    25 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    26 pages
    German language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 1452-1:2009(Main)
Plastics piping systems for water supply and for buried and above-ground drainage and sewerage under pressure - Unplasticized poly(vinyl chloride) (PVC-U) - Part 1: General (ISO 1452-1:2009)
SIST EN ISO 1452-1:2010

ISO 1452-1:2009 specifies the general aspects of unplasticized poly(vinyl chloride) (PVC‑U) solid-wall piping systems intended for water supply and for buried and above ground drainage and sewerage under pressure.
In conjunction with ISO 1452-2, ISO 1452-3, ISO 1452-4 and ISO 1452-5, it is applicable to PVC‑U pipes, fittings, valves and ancillary equipment, their joints and to joints with components of other plastics and non-plastics materials intended to be used for the following:
- water mains and services buried in the ground;
- conveyance of water above ground for both outside and inside buildings;
- buried and above ground drainage and sewerage under pressure.
It is applicable to piping systems intended for the supply of water under pressure up to and including 25 °C (cold water), intended for human consumption and for general purposes as well as for waste water under pressure. It is also applicable to components for the conveyance of water and waste water up to and including 45 °C.

  • Standard
    19 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 1452-2:2009(Main)
Plastics piping systems for water supply and for buried and above-ground drainage and sewerage under pressure - Unplasticized poly(vinyl chloride) (PVC-U) - Part 2: Pipes (ISO 1452-2:2009)
SIST EN ISO 1452-2:2010

ISO 1452-2:2009 specifies the characteristics of solid-wall pipes made from unplasticized poly(vinyl chloride) (PVC‑U) for piping systems intended for water supply and for buried and above ground drainage and sewerage under pressure. It also specifies the test parameters for the test methods referred to.
In conjunction with ISO 1452-1 and ISO 1452-5, it is applicable to extruded PVC‑U pipes without a socket and pipes with a socket (integral or not), intended to be used for the following:
- water mains and services buried in the ground;
- conveyance of water above ground for both outside and inside buildings;
- buried and above ground drainage and sewerage under pressure.
It is applicable to piping systems intended for the supply of water under pressure up to and including 25 °C (cold water) intended for human consumption and for general purposes as well as for waste water under pressure. It is also applicable to pipes for the conveyance of water and waste water up to and including 45 °C and to a range of pipe sizes and pressure classes. It gives requirements concerning colours.

  • Standard
    31 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 22391-5:2009(Main)
Plastics piping systems for hot and cold water installations - Polyethylene of raised temperature resistance (PE-RT) - Part 5: Fitness for purpose of the system (ISO 22391-5:2009)
SIST EN ISO 22391-5:2010

ISO 22391-5:2009 specifies the characteristics of the fitness for purpose of piping systems made of polyethylene of raised temperature resistance (PE-RT), Type I and polyethylene of raised temperature resistance (PE-RT), Type II, intended to be used for hot and cold water installations within buildings for the conveyance of water, whether or not the water is intended for human consumption (domestic systems) and for heating systems, under the design pressures and temperatures appropriate to the class of application according to ISO 22391-1.
ISO 22391-5:2009 covers a range of service conditions (classes of application), design pressures and pipe dimension classes, and also specifies test parameters and test methods. In conjunction with the other parts of ISO 22391, it is applicable to PE-RT pipes, fittings, their joints, and to joints having components of PE-RT as well as of other plastics and non-plastics materials, respectively, used for hot and cold water installations.

  • Standard
    16 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 22391-1:2009(Main)
Plastics piping systems for hot and cold water installations - Polyethylene of raised temperature resistance (PE-RT) - Part 1: General (ISO 22391-1:2009)
SIST EN ISO 22391-1:2010

ISO 22391-1:2009 specifies the general characteristics of piping systems made of polyethylene of raised temperature resistance (PE‑RT), Type I and polyethylene of raised temperature resistance (PE-RT), Type II intended to be used for hot and cold water installations within buildings for the conveyance of water, whether or not the water is intended for human consumption (domestic systems) and for heating systems, under specified design pressures and temperatures appropriate to the class of application.
ISO 22391-1:2009 covers a range of service conditions (classes of application), design pressures and pipe dimension classes, and also specifies test parameters and defines terms. In conjunction with the other parts of ISO 22391, it is applicable to PE-RT pipes, fittings, their joints and to joints having components of PE-RT, as well as of other plastics and non-plastics materials, respectively, used for hot and cold water installations.

  • Standard
    17 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 1452-4:2009(Main)
Plastics piping systems for water supply and for buried and above-ground drainage and sewerage under pressure - Unplasticized poly(vinyl chloride) (PVC-U) - Part 4: Valves (ISO 1452-4:2009)
SIST EN ISO 1452-4:2010

ISO 1452-4:2009 specifies the characteristics of valves made from unplasticized poly(vinyl chloride) (PVC‑U) for piping systems intended for water supply and for buried and above-ground drainage and sewerage under pressure. It also specifies the test parameters for the test methods referred to.
In conjunction with ISO 1452-1, ISO 1452-2, ISO 1452-3 and ISO 1452-5 it is applicable to PVC‑U valves with components of PVC-U, other plastics and non-plastics materials intended to be used for the following:
- water mains and services buried in ground;
- conveyance of water above ground for both outside and inside buildings;
- buried and above-ground drainage and sewerage under pressure.
It is applicable to valves in piping systems intended for the supply of water under pressure up to and including 25 °C (cold water) intended for human consumption and for general purposes as well as for waste water under pressure. It is also applicable to valves for the conveyance of water and waste water up to and including 45 °C.

  • Standard
    19 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 22391-5:2009/A1:2020(Amendment)
Plastics piping systems for hot and cold water installations - Polyethylene of raised temperature resistance (PE-RT) - Part 5: Fitness for purpose of the system - Amendment 1 (ISO 22391-5:2009/Amd 1:2020, Corrected version 2021-03)
SIST EN ISO 22391-5:2010/A1:2021
  • Amendment
    9 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Amendment
    9 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
CEN ISO/TS 22391-7:2018(Main)
Plastics piping systems for hot and cold water installations - Polyethylene of raised temperature resistance (PE-RT) - Part 7: Guidance for the assessment of conformity (ISO/TS 22391-7:2018)
SIST-TS CEN ISO/TS 22391-7:2019

This part of ISO 22391 gives guidance for the assessment of conformity of materials, products, and assemblies in accordance with the applicable part(s) of ISO 22391 intended to be included in the manufacturer’s quality plan as part of the quality management system and for the establishment of certification procedures.
In conjunction with the other parts of ISO 22391 (see Foreword), this Technical Specification is applicable to polyethylene of raised temperature resistance (PE-RT) piping systems intended to be used for hot and cold water installations within buildings for the conveyance of water, whether or not intended for human consumption (domestic systems) and for heating systems, under design pressures and temperatures appropriate to the class of application (see Table 1 of ISO 22391:2009).

  • Technical specification
    25 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    26 pages
    German language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 22391-5:2009(Main)
Plastics piping systems for hot and cold water installations - Polyethylene of raised temperature resistance (PE-RT) - Part 5: Fitness for purpose of the system (ISO 22391-5:2009)
SIST EN ISO 22391-5:2010

ISO 22391-5:2009 specifies the characteristics of the fitness for purpose of piping systems made of polyethylene of raised temperature resistance (PE-RT), Type I and polyethylene of raised temperature resistance (PE-RT), Type II, intended to be used for hot and cold water installations within buildings for the conveyance of water, whether or not the water is intended for human consumption (domestic systems) and for heating systems, under the design pressures and temperatures appropriate to the class of application according to ISO 22391-1.
ISO 22391-5:2009 covers a range of service conditions (classes of application), design pressures and pipe dimension classes, and also specifies test parameters and test methods. In conjunction with the other parts of ISO 22391, it is applicable to PE-RT pipes, fittings, their joints, and to joints having components of PE-RT as well as of other plastics and non-plastics materials, respectively, used for hot and cold water installations.

  • Standard
    16 pages
    English language
    sale 10% off
    e-Library read for
    1 day