EN ISO 25178-2:2012
(Main)Geometrical product specifications (GPS) - Surface texture: Areal - Part 2: Terms, definitions and surface texture parameters (ISO 25178-2:2012)
Geometrical product specifications (GPS) - Surface texture: Areal - Part 2: Terms, definitions and surface texture parameters (ISO 25178-2:2012)
ISO 25178-2:2012 specifies terms, definitions and parameters for the determination of surface texture by areal methods.
Geometrische Produktspezifikation (GPS) - Oberflächenbeschaffenheit: Flächenhaft - Teil 2: Begriffe und Oberflächen-Kenngrößen (ISO 25178-2:2012)
Dieser Teil von ISO 25178 legt die Benennungen, Definitionen und Parameter für die Ermittlung der Oberflächenbeschaffenheit durch flächenhafte Verfahren fest.
Spécification géométrique des produits (GPS) - Etat de surface: Surfacique - Partie 2: Termes, définitions et paramètres d'états de surface (ISO 25178-2:2012)
L'ISO 25178:2012 spécifie les termes, définitions et paramètres applicables à la détermination de l'état de surface au moyen de méthodes surfaciques.
Specifikacija geometrijskih veličin izdelka - Tekstura površine: ploskovna - 2. del: Poimenovanja, definicije in parametri teksture površine (ISO 25178-2:2012)
Ta mednarodni standard določa minimalne zahteve za instrumente in sisteme iz razreda topografov roženice (CT). Določa tudi preskuse in postopke za preverjanje, ali je sistem ali instrument v skladu s tem mednarodnim standardom, pri čemer se zato lahko opredeli kot topograf roženice v skladu s tem mednarodnim standardom. Določa tudi preskuse in postopke, ki omogočajo preverjanje zmogljivosti sistemov, ki presegajo minimalne zahteve za topografe roženice. Ta mednarodni standard opredeljuje izraze, ki so specifični za ugotavljanje oblike roženice, da bodo standardizirani na celotnem področju očesne optike. Ta mednarodni standard se uporablja za instrumente, sisteme in metode za merjenje površinske oblike roženice človeškega očesa.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 25178-2:2012
01-september-2012
6SHFLILNDFLMDJHRPHWULMVNLKYHOLþLQL]GHOND7HNVWXUDSRYUãLQH SORVNRYQDGHO
3RLPHQRYDQMDGHILQLFLMHLQSDUDPHWULWHNVWXUHSRYUãLQH ,62
Geometrical product specifications (GPS) - Surface texture: Areal - Part 2: Terms,
definitions and surface texture parameters (ISO 25178-2:2012)
Geometrische Produktspezifikation (GPS) - Oberflächenbeschaffenheit: Flächenhaft -
Teil 2: Begriffe und Oberflächen-Kenngrößen (ISO 25178-2:2012)
Spécification géométrique des produits (GPS) - État de surface: surfacique - Partie 2:
Termes, définitions et paramètres d'états de surface (ISO 25178-2:2012)
Ta slovenski standard je istoveten z: EN ISO 25178-2:2012
ICS:
17.040.20 Lastnosti površin Properties of surfaces
SIST EN ISO 25178-2:2012 en,fr
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 25178-2:2012
---------------------- Page: 2 ----------------------
SIST EN ISO 25178-2:2012
EUROPEAN STANDARD
EN ISO 25178-2
NORME EUROPÉENNE
EUROPÄISCHE NORM
April 2012
ICS 17.040.20
English Version
Geometrical product specifications (GPS) - Surface texture:
Areal - Part 2: Terms, definitions and surface texture parameters
(ISO 25178-2:2012)
Spécification géométrique des produits (GPS) - Etat de Geometrische Produktspezifikation (GPS) -
surface: Surfacique - Partie 2: Termes, définitions et Oberflächenbeschaffenheit: Flächenhaft - Teil 2: Begriffe
paramètres d'états de surface (ISO 25178-2:2012) und Oberflächen-Kenngrößen (ISO 25178-2:2012)
This European Standard was approved by CEN on 17 September 2011.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2012 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 25178-2:2012: E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 25178-2:2012
EN ISO 25178-2:2012 (E)
Contents Page
Foreword .3
2
---------------------- Page: 4 ----------------------
SIST EN ISO 25178-2:2012
EN ISO 25178-2:2012 (E)
Foreword
This document (EN ISO 25178-2:2012) has been prepared by Technical Committee ISO/TC 213 "Dimensional
and geometrical product specifications and verification" in collaboration with Technical Committee
CEN/TC 290 “Dimensional and geometrical product specification and verification” the secretariat of which is
held by AFNOR.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by October 2012, and conflicting national standards shall be withdrawn at
the latest by October 2012.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland, Turkey and the United Kingdom.
Endorsement notice
The text of ISO 25178-2:2012 has been approved by CEN as a EN ISO 25178-2:2012 without any
modification.
3
---------------------- Page: 5 ----------------------
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.