iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CEN

EN ISO 11403-3:2001

(Main)

Plastics - Acquisition and presentation of comparable multipoint data - Part 3: Environmental influences on properties (ISO 11403-3:1999)

Plastics - Acquisition and presentation of comparable multipoint data - Part 3: Environmental influences on properties (ISO 11403-3:1999)

Kunststoffe - Ermittlung und Darstellung vergleichbarer Vielpunkt-Kennwerte - Teil 3: Umgebungseinflüsse auf Eigenschaften (ISO 11403-3:1999)

Dieser Teil von ISO 11403 legt Prüfverfahren fest für die Ermittlung und Darstellung von Vielpunkt-Kennwerten, die das Verhalten von Kunststoffen gegenüber den folgenden Umgebungseinflüssen darstellen:
¾ langanhaltende Wärmeeinwirkung,
¾ flüssige Medien,
¾ umgebungsbedingte Spannungsrissbildung unter konstanter Zugbeanspruchung,
¾ künstliche Bewitterung.
Die Prüfungen sind in der Reihenfolge zunehmender Schärfe aufgeführt. Durch Prüfung bei weniger scharfen Umgebungseinflüssen ist es möglich zu entscheiden, ob Prüfungen unter schärferen Bedingungen sinnvoll sind.

Plastiques - Acquisition et présentation de données multiples comparables - Partie 3: Effets induits par l'environnement sur les propriétés (ISO 11403-3:1999)

La présente partie de l'ISO 11403 prescrit les modes opératoires d'essai en vue de l'acquisition et de la présentation de données multiples qui démontrent le comportement des plastiques dans les environnements suivants: - exposition prolongée à la chaleur; - produits chimiques liquides; - fissuration dans un environnement donné sous contrainte de traction constante; - vieillissement artificiel. Les essais sont indiqués par ordre de sévérité croissante de l'effet de l'environnement. Commencer par les environnements les moins sévères permet de juger en toute connaissance de cause s'il vaut la peine d'effectuer des essais dans des conditions plus sévères.

Polimerni materiali - Pridobitev in predstavitev primerljivih značilnih enotočkovnih podatkov - 3. del: Vplivi okolja na lastnosti (ISO 11403-3:1999)

General Information

Status
Withdrawn
Publication Date
20-Mar-2001
Withdrawal Date
17-Jun-2014
ICS
83.080.01 - Plastics in general
83.080.10 - Thermosetting materials
Technical Committee
CEN/TC 249 - Plastics
Drafting Committee
CEN/TC 249 - Plastics
Current Stage
9960 - Withdrawal effective - Withdrawal
Completion Date
18-Jun-2014
Ref Project
SIST EN ISO 11403-3:2002 - Plastics - Acquisition and presentation of comparable multipoint data - Part 3: Environmental influences on properties (ISO 11403-3:1999)

Relations

Replaced By
EN ISO 11403-3:2014 - Plastics - Acquisition and presentation of comparable multipoint data - Part 3: Environmental influences on properties (ISO 11403-3:2014)
Effective Date
08-Jun-2022

Buy Standard

EN ISO 11403-3:2002EN ISO 11403-3:2002
PreviousNext
Standard
EN ISO 11403-3:2002
English language
16 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 11403-3:2002
01-februar-2002
3ROLPHUQLPDWHULDOL3ULGRELWHYLQSUHGVWDYLWHYSULPHUOMLYLK]QDþLOQLKHQRWRþNRYQLK
SRGDWNRYGHO9SOLYLRNROMDQDODVWQRVWL ,62
Plastics - Acquisition and presentation of comparable multipoint data - Part 3:
Environmental influences on properties (ISO 11403-3:1999)
Kunststoffe - Ermittlung und Darstellung vergleichbarer Vielpunkt-Kennwerte - Teil 3:
Umgebungseinflüsse auf Eigenschaften (ISO 11403-3:1999)
Plastiques - Acquisition et présentation de données multiples comparables - Partie 3:
Effets induits par l'environnement sur les propriétés (ISO 11403-3:1999)
Ta slovenski standard je istoveten z: EN ISO 11403-3:2001
ICS:
83.080.01 Polimerni materiali na Plastics in general
splošno
SIST EN ISO 11403-3:2002 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 11403-3:2002

---------------------- Page: 2 ----------------------

SIST EN ISO 11403-3:2002
EUROPEAN STANDARD
EN ISO 11403-3
NORME EUROPÉENNE
EUROPÄISCHE NORM
March 2001
ICS 83.080.01; 83.080.10
English version
Plastics - Acquisition and presentation of comparable multipoint
data - Part 3: Environmental influences on properties (ISO
11403-3:1999)
Plastiques - Acquisition et présentation de données Kunststoffe - Ermittlung und Darstellung vergleichbarer
multiples comparables - Partie 3: Effets induits par Vielpunkt-Kennwerte - Teil 3: Umgebungseinflüsse auf
l'environnement sur les propriétés (ISO 11403-3:1999) Eigenschaften (ISO 11403-3:1999)
This European Standard was approved by CEN on 4 February 2001.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,
Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2001 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 11403-3:2001 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN ISO 11403-3:2002
EN ISO 11403-3:2001 (E)
Foreword
The text of the International Standard from Technical Committee ISO/TC 61 "Plastics" of the
International Organization for Standardization (ISO) has been taken over as an European
Standard by Technical Committee CEN/TC 249 "Plastics", the secretariat of which is held by
IBN.
This European Standard shall be given the status of a national standard, either by publication
of an identical text or by endorsement, at the latest by September 2001, and conflicting
national standards shall be withdrawn at the latest by September 2001.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of
the following countries are bound to implement this European Standard: Austria, Belgium,
Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy,
Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United
Kingdom.
Endorsement notice
The text of the International Standard ISO 11403-3:1999 has been approved by CEN as a
European Standard without any modification.
NOTE: Normative references to International Standards are listed in annex ZA (normative).
2

---------------------- Page: 4 ----------------------

SIST EN ISO 11403-3:2002
EN ISO 11403-3:2001 (E)
Annex ZA (normative)
Normative references to international publications
with their relevant European publications
This European Standard incorporates by dated or undated reference, provisions from other
publications. These normative references are cited at the appropriate places in the text and the
publications are listed hereafter. For dated references, subsequent amendments to or revisions
of any of these publications apply to this European Standard only when incorporated in it by
amendment or revision. For undated references the latest edition of the publication referred to
applies (including amendments).
NOTE Where an International Publication has been modified by common modifications,
indicated by (mod.), the relevant EN/HD applies.
Pub
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN
EN ISO 75-2:2013(Main)
Plastics - Determination of temperature of deflection under load - Part 2: Plastics and ebonite (ISO 75-2:2013)
SIST EN ISO 75-2:2013

ISO 75-2:2013 specifies three methods, using different values of constant flexural stress, which can be used for the determination of the temperature of deflection under load of plastics (including filled plastics and fibre-reinforced plastics in which the fibre length, prior to processing, is up to 7,5 mm) and ebonite:
method A, using a flexural stress of 1,80 MPa;
method B, using a flexural stress of 0,45 MPa;
method C, using a flexural stress of 8,00 MPa.

  • Standard
    17 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 175:2010(Main)
Plastics - Methods of test for the determination of the effects of immersion in liquid chemicals (ISO 175:2010)
SIST EN ISO 175:2011

ISO 175:2010 specifies a method of exposing test specimens of plastic materials, free from all external restraint, to liquid chemicals, and methods for determining the changes in properties resulting from such immersion. It does not cover environmental stress cracking (ESC) which is dealt with by the various parts of ISO 22088.
It only considers testing by immersion of the entire surface of the test specimen.
It is applicable to all solid plastics that are available in the form of moulding or extrusion materials, plates, tubes, rods or sheets having a thickness greater than 0,1 mm. It is not applicable to cellular materials.

  • Standard
    28 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 6603-1:2000(Main)
Plastics - Determination of puncture impact behaviour of rigid plastics - Part 1: Non-instrumented impact testing (ISO 6603-1:2000)
SIST EN ISO 6603-1:2000

This International Standard specifies methods for the determination of puncture-impact properties of rigid plastics in
the form of flat test specimens, such as discs or square pieces, under defined conditions. Specimens may be
moulded directly, cut from sheets or taken from finished products. Different types of test specimens and test
conditions are defined.
These falling-dart methods are used to investigate the behaviour of plastic sheeting or mouldings under the impact
of a striker applied perpendicular to the plane of the specimen.
This part of ISO 6603 can be used if it is sufficient to characterize the impact behaviour of plastics by a threshold
value of impact-failure energy based on many test specimens. ISO 6603-2 is used if a force-deflection or force-time
diagram, recorded at nominally constant striker velocity, is necessary for detailed characterization of the impact
behaviour.
These test methods are applicable to specimens with a thickness between 1 mm and 4 mm.
NOTE For thicknesses less than 1 mm, ISO 7765 should preferably be used. Thicknesses greater than 4 mm may be
tested if the equipment is suitable, but the test falls outside the scope of ISO 6603-1 and ISO 6603-2.
These methods are suitable for use with the following types of material:
_ rigid thermoplastic moulding and extrusion materials, including filled, unfilled and reinforced compounds and
sheets;
_ rigid thermosetting moulding and extrusion materials, including filled and reinforced compounds, sheets and
laminates;
_ fibre-reinforced thermoset and thermoplastic composites incorporating unidirectional or non-unidirectional
reinforcements such as mats, woven fabrics, woven rovings, chopped strands, combination and hybrid
reinforcements, rovings, milled fibres and sheets made from pre-impregnated materials (prepregs).
These methods are also applicable to specimens which are either moulded or machined from finished products,
laminates and extruded or cast sheet.
The test results are comparable only if the conditions of preparation of the specimens, their dimensions and
surfaces as well as the test conditions are the same. In particular, results determined on specimens of different
thickness cannot be compared with one another (see annex E of ISO 6603-2:—). Comprehensive evaluation of the
reaction to impact stress requires that determinations be made as a function of impact velocity and temperature for
different material variables, such as crystallinity and moisture content.
The impact behaviour of finished products cannot be predicted directly from this test, but specimens may be taken
from finished products (see above) for test by these methods.
Test data developed by these methods should not be used for design calculations. However, information on the
typical behaviour of the material can be obtained by testing at different temperatures and impact velocities (see
annex D of ISO 6603-2:—), by varying the thickness (see annex E of ISO 6603-2:—) and by testing specimens
prepared under different conditions.
Two statistical methods of test are described in this part of ISO 6603:
_ Method A: staircase method (individual) (preferred)
In this method, a uniform energy increment is employed during testing. The energy is decreased or increased
by the uniform increment after testing each specimen, depending upon the observed result (pass or fail) for the
preceding test.
_ Method B: group method (optional)
In this method, successive groups of at least ten test specimens are t

  • Standard
    17 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
prEN ISO 9773(Main)
Plastics - Determination of burning behaviour of thin flexible vertical specimens in contact with a small-flame ignition source (ISO/DIS 9773:2011)
oSIST prEN ISO 9773:2011

2014-11-24: WI cancelled following cancellation of equivalent ISO standard (see ISO notification in dataservice on 2014-11-24).

  • Draft
    20 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 75-2:2013(Main)
Plastics - Determination of temperature of deflection under load - Part 2: Plastics and ebonite (ISO 75-2:2013)
SIST EN ISO 75-2:2013

ISO 75-2:2013 specifies three methods, using different values of constant flexural stress, which can be used for the determination of the temperature of deflection under load of plastics (including filled plastics and fibre-reinforced plastics in which the fibre length, prior to processing, is up to 7,5 mm) and ebonite:
method A, using a flexural stress of 1,80 MPa;
method B, using a flexural stress of 0,45 MPa;
method C, using a flexural stress of 8,00 MPa.

  • Standard
    17 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 175:2010(Main)
Plastics - Methods of test for the determination of the effects of immersion in liquid chemicals (ISO 175:2010)
SIST EN ISO 175:2011

ISO 175:2010 specifies a method of exposing test specimens of plastic materials, free from all external restraint, to liquid chemicals, and methods for determining the changes in properties resulting from such immersion. It does not cover environmental stress cracking (ESC) which is dealt with by the various parts of ISO 22088.
It only considers testing by immersion of the entire surface of the test specimen.
It is applicable to all solid plastics that are available in the form of moulding or extrusion materials, plates, tubes, rods or sheets having a thickness greater than 0,1 mm. It is not applicable to cellular materials.

  • Standard
    28 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 6603-1:2000(Main)
Plastics - Determination of puncture impact behaviour of rigid plastics - Part 1: Non-instrumented impact testing (ISO 6603-1:2000)
SIST EN ISO 6603-1:2000

This International Standard specifies methods for the determination of puncture-impact properties of rigid plastics in
the form of flat test specimens, such as discs or square pieces, under defined conditions. Specimens may be
moulded directly, cut from sheets or taken from finished products. Different types of test specimens and test
conditions are defined.
These falling-dart methods are used to investigate the behaviour of plastic sheeting or mouldings under the impact
of a striker applied perpendicular to the plane of the specimen.
This part of ISO 6603 can be used if it is sufficient to characterize the impact behaviour of plastics by a threshold
value of impact-failure energy based on many test specimens. ISO 6603-2 is used if a force-deflection or force-time
diagram, recorded at nominally constant striker velocity, is necessary for detailed characterization of the impact
behaviour.
These test methods are applicable to specimens with a thickness between 1 mm and 4 mm.
NOTE For thicknesses less than 1 mm, ISO 7765 should preferably be used. Thicknesses greater than 4 mm may be
tested if the equipment is suitable, but the test falls outside the scope of ISO 6603-1 and ISO 6603-2.
These methods are suitable for use with the following types of material:
_ rigid thermoplastic moulding and extrusion materials, including filled, unfilled and reinforced compounds and
sheets;
_ rigid thermosetting moulding and extrusion materials, including filled and reinforced compounds, sheets and
laminates;
_ fibre-reinforced thermoset and thermoplastic composites incorporating unidirectional or non-unidirectional
reinforcements such as mats, woven fabrics, woven rovings, chopped strands, combination and hybrid
reinforcements, rovings, milled fibres and sheets made from pre-impregnated materials (prepregs).
These methods are also applicable to specimens which are either moulded or machined from finished products,
laminates and extruded or cast sheet.
The test results are comparable only if the conditions of preparation of the specimens, their dimensions and
surfaces as well as the test conditions are the same. In particular, results determined on specimens of different
thickness cannot be compared with one another (see annex E of ISO 6603-2:—). Comprehensive evaluation of the
reaction to impact stress requires that determinations be made as a function of impact velocity and temperature for
different material variables, such as crystallinity and moisture content.
The impact behaviour of finished products cannot be predicted directly from this test, but specimens may be taken
from finished products (see above) for test by these methods.
Test data developed by these methods should not be used for design calculations. However, information on the
typical behaviour of the material can be obtained by testing at different temperatures and impact velocities (see
annex D of ISO 6603-2:—), by varying the thickness (see annex E of ISO 6603-2:—) and by testing specimens
prepared under different conditions.
Two statistical methods of test are described in this part of ISO 6603:
_ Method A: staircase method (individual) (preferred)
In this method, a uniform energy increment is employed during testing. The energy is decreased or increased
by the uniform increment after testing each specimen, depending upon the observed result (pass or fail) for the
preceding test.
_ Method B: group method (optional)
In this method, successive groups of at least ten test specimens are t

  • Standard
    17 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
prEN ISO 9773(Main)
Plastics - Determination of burning behaviour of thin flexible vertical specimens in contact with a small-flame ignition source (ISO/DIS 9773:2011)
oSIST prEN ISO 9773:2011

2014-11-24: WI cancelled following cancellation of equivalent ISO standard (see ISO notification in dataservice on 2014-11-24).

  • Draft
    20 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 16739-1:2024(Main)
Industry Foundation Classes (IFC) for data sharing in the construction and facility management industries - Part 1: Data schema (ISO 16739-1:2024)
kSIST FprEN ISO 16739-1:2024

This document represents an open international standard for information used in Building Information Modeling (BIM) that is exchanged and shared among software applications used by the various participants in the construction or facility management industry sector. This document includes definitions that cover information required for buildings and infrastructure works over their life cycle. This edition of the document added coverage of information required for infrastructure facilities including bridges, roads, railways, waterways and port facilities.
This document comprises the publication of a data schema, its documentation, the property and quantity set definitions and the mechanism of an exchange file format structure.
Definitions from this document are used to support different recognized work flows in the construction and facility management industry sector, representing information deliveries. Such information deliveries can be described according to ISO 29481.
Different implementation levels of this document can be defined to better support multiple information deliveries, they are referred to as a Model View Definition (MVD). Each MVD identifies which subset of the definitions of this document imposes requirements for implementation in software applications. Conforming software applications need to identify the model view definition they conform to when applying for software certification.
The following are within the scope of this edition of this document:
BIM exchange format definitions that are required during the life cycle phases of buildings and infrastructure:
demonstrating the need;
conception of need;
outline feasibility;
substantive feasibility study and outline financial authority;
outline conceptual design;
full conceptual design;
coordinated design;
procurement and full financial authority;
production information;
construction;
operation and maintenance.
BIM exchange format definitions that are required by the various disciplines involved within the life cycle phases:
architecture and civil engineering design;
service and utilities engineering;
structural engineering;
procurement;
construction planning;
facility and utility management;
project management;
client requirement management;
industry authorities for permits and approval.
BIM exchange format definitions including:
project structure;
physical components;
spatial components;
analysis items;
processes;
resources;
controls;
actors;
context definition.

  • Draft
    406 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 17294-1:2024(Main)
Water quality - Application of inductively coupled plasma mass spectrometry (ICP-MS) - Part 1: General requirements (ISO 17294-1:2024)
kSIST FprEN ISO 17294-1:2023

This document specifies the principles of inductively coupled plasma mass spectrometry (ICP-MS) and provides general requirements for the use of this technique to determine elements in water, digests of sludges and sediments (e.g. digests of water as described in ISO 15587-1 or ISO 15587-2). Generally, the measurement is carried out in water, but gases, vapours or fine particulate matter can be introduced too. This document applies to the use of ICP-MS for aqueous solution analysis.
The ultimate determination of the elements is described in a separate International Standard for each series of elements and matrix. The individual clauses of this document refer the user to these guidelines for the basic principles of the method and the configuration of the instrument.

  • Draft
    43 pages
    English language
    sale 10% off
    e-Library read for
    1 day