iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CEN

FprEN 13852-1

(Main)

Cranes - Offshore cranes - Part 1: General-purpose offshore cranes

Cranes - Offshore cranes - Part 1: General-purpose offshore cranes

This document applies to general purpose offshore cranes including their supporting pedestals and structures.
This document is applicable to general purpose offshore cranes, whose structures are made of steel.
This document provides requirements for all significant hazards, hazardous situations and events relevant to general purpose offshore cranes, for lifting of goods and lifting of persons, when used as intended and under the conditions foreseen by the risk assessment (see Clause 4).
This document is applicable to general purpose offshore cranes, which are manufactured after the date of approval by CEN of this document.
This document is not applicable for:
a)   transportation, assembly, disabling, scrapping, installation or erecting of the crane;
b)   any item attached to the hook, such as loads, non-fixed load lifting attachments, lifting accessories, baskets, carriers and containers;
c)   lifting operations in ambient temperatures below - 20 °C;
d)   lifting operations in ambient temperatures above 45 °C;
e)   accidental loads as result of collisions, earthquakes, explosions, etc., which are not covered by exceptional loads defined in Table B.7 ;
f)   floating cranes (covered by EN13852-2), light offshore cranes (covered by FprEN13852-3) and 2D/3D motion compensated cranes;
g)   subsea lifting operations;
h)   lifting operations involving more than one crane;
i)   emergency rescue operations (except training).

Krane - Offshore-Krane - Teil 1: Offshore-Krane für allgemeine Verwendung

Dieses Dokument gilt für Offshore-Krane für allgemeine Verwendung einschließlich ihrer Tragsäulen und Strukturen.
Dieses Dokument gilt für Offshore-Krane für allgemeine Verwendung mit Strukturen aus Stahl.
Dieses Dokument enthält Anforderungen für alle signifikanten Gefährdungen, Gefährdungssituationen und Ereignisse, die für Offshore-Krane für allgemeine Verwendung, das Anheben von Gütern und Personen bei bestimmungsgemäßem Gebrauch und unter den durch die Risikobewertung vorgesehenen Bedingungen (siehe Abschnitt 4) relevant sind.
Dieses Dokument gilt für Offshore-Krane für allgemeine Verwendung, die nach dem Datum der Genehmigung dieses Dokuments durch die CEN hergestellt werden.
Diese Dokument gilt nicht für:
a)   den Transport, die Montage, die Demontage, die Verschrottung, die Installation oder die Errichtung des Krans;
b)   alle an dem Haken befestigten Objekte wie etwa Lasten, nicht fest angebrachte Lastaufnahmemittel, Hebezubehör, Körbe, Träger und Behälter;
c)   Hebearbeiten bei Umgebungstemperaturen unter −20 °C;
d)   Hebearbeiten bei Umgebungstemperaturen über 45 °C;
e)   zufällige Lasten aufgrund von Kollisionen, Erdbeben, Explosionen usw., die nicht durch die in Tabelle B.7 festgelegten außergewöhnlichen Lasten abgedeckt sind;
f)   Schwimmkrane (behandelt in EN 13852 2), leichte Offshore-Krane (behandelt in FprEN 13852 3) und 2D/3D-bewegungskompensierte Krane;
g)   Unterwasser-Hebearbeiten;
h)   Hebearbeiten mit mehr als einem beteiligten Kran;
i)   Rettungsmaßnahmen in Notfällen (ausgenommen Training).

Appareils de levage à charge suspendue - Grues off-shore - Partie 1 : Grues off-shore pour usage général

Le présent document s'applique aux grues off-shore d'usage général, y compris à leurs socles et aux structures d'appui.
Le présent document s'applique aux grues off-shore d'usage général à structure en acier.
Le présent document spécifie les prescriptions relatives à l'ensemble des phénomènes dangereux, situations dangereuses et événements dangereux majeurs relatifs aux grues off-shore d'usage général, pour le transport de marchandises et le levage de personnes, lorsque celles-ci sont utilisées comme prévu et dans les conditions prévues par l'évaluation du risque (voir Article 4).
Le présent document s'applique aux grues off-shore d'usage général fabriquées après la date d'approbation du présent document par le CEN.
Le présent document ne s'applique pas :
a)   au transport, au montage, au démontage, à la mise au rebut ou à l'installation de la grue ;
b)   à tout élément fixé au crochet, tel que les charges, les accessoires de levage de charge amovibles, les accessoires de levage, les nacelles, les supports et les conteneurs ;
c)   aux opérations de levage à des températures ambiantes inférieures à - 20 °C ;
d)   aux opérations de levage à des températures ambiantes supérieures à 45 °C ;
e)   aux charges accidentelles résultant de collisions, de tremblements de terre, d'explosions, etc., qui ne sont pas couvertes par les charges exceptionnelles définies dans le Tableau B.7 ;
f)   aux grues flottantes (couvertes par l'EN 13852-2), aux grues off-shore légères (couvertes par FprEN 13852-3) et aux grues à compensation de mouvement 2D/3D ;
g)   aux opérations de levage sous-marines ;
h)   aux opérations de levage impliquant plus d'un appareil de levage à charge suspendue ;
i)   aux opérations de sauvetage (hors entraînement).

Dvigala (žerjavi) - Dvigala na plavajočih objektih - 1. del: Dvigala na plavajočih objektih za splošne namene

General Information

Status
Not Published
Publication Date
04-Oct-2022
ICS
47.020.40 - Lifting and cargo handling equipment
53.020.20 - Cranes
Technical Committee
CEN/TC 147 - Cranes - Safety
Drafting Committee
CEN/TC 147/WG 15 - Offshore cranes
Current Stage
4599 - Dispatch of FV draft to CMC - Finalization for Vote
Start Date
08-Jun-2023
Due Date
03-Dec-2021
Completion Date
08-Jun-2023
Directive
2006/42/EC - Directive 2006/42/EC of the European Parliament and of the Council of 17 May 2006 on machinery, and amending Directive 95/16/EC (recast)
2014/34/EU - Directive 2014/34/EU Of The European Parliament And Of The Council of 26 February 2014 on the harmonisation of the laws of the Member States relating to equipment and protective systems intended for use in potentially explosive atmospheres (recast)
98/37/EC - Machinery
Mandate
M/079 - Mandate to CEN and CENELEC for standardization in the field of machines
M/396 - Mandate to CEN and Cenelec for standardisation in the field of machinery
M/596 - [C(2023)4798] Commission Implementing Decision of 20.7.2023 on a standardisation request as regards equipment and protective systems intended for use in potentially explosive atmospheres in support of Directive 2014/34/EU (ATEX) of the European Parliament and of the Council
Ref Project
oSIST prEN 13852-1:2009 - Cranes - Offshore cranes - Part 1: General-purpose offshore cranes

Relations

Revises
EN 13852-1:2013 - Cranes - Offshore cranes - Part 1: General-purpose offshore cranes
Effective Date
19-Jan-2023

Buy Standard

prEN 13852-1:2009prEN 13852-1:2009
PreviousNext
Draft
prEN 13852-1:2009
English language
89 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
oSIST prEN 13852-1:2009
01-november-2009
'YLJDOD åHUMDYL 'YLJDODQDSODYDMRþLKREMHNWLKGHO'YLJDODQDSODYDMRþLK
REMHNWLK]DVSORãQHQDPHQH
Cranes - Offshore cranes - Part 1: General-purpose offshore cranes
Krane - Offshore-Krane - Teil 1: Offshore-Krane für allegemeine Verwendung
Appareils de levage - Appareils de levage offshore - Partie 1: Appareils de levage
offshore pour usage général
Ta slovenski standard je istoveten z: prEN 13852-1
ICS:
47.020.40 Dvigalna oprema in oprema Lifting and cargo handling
za pretovor equipment
53.020.20 Dvigala Cranes
oSIST prEN 13852-1:2009 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
oSIST prEN 13852-1:2009

---------------------- Page: 2 ----------------------
oSIST prEN 13852-1:2009
EUROPEAN STANDARD
DRAFT
prEN 13852-1
NORME EUROPÉENNE
EUROPÄISCHE NORM
July 2009
ICS Will supersede EN 13852-1:2004
English Version
Cranes - Offshore cranes - Part 1: General-purpose offshore
cranes
Appareils de levage - Appareils de levage offshore - Partie Krane - Offshore-Krane - Teil 1: Offshore-Krane für
1: Appareils de levage offshore pour usage général allegemeine Verwendung
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee CEN/TC 147.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations which
stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other language
made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the
same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are aware and to
provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2009 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 13852-1:2009: E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------
oSIST prEN 13852-1:2009
prEN 13852-1:2009 (E)
Contents Page
Foreword .6
Introduction .7
1 Scope .8
2 Normative references .8
3 Terms and definitions . 12
4 List of significant hazards . 16
5 Safety requirements and/or protective measures . 17
5.1 General . 17
5.2 Strength and stability . 17
5.2.1 Selection of classification parameters . 17
5.2.2 In-service loads . 18
5.2.3 Out of service loads . 19
5.2.4 Failure mode analysis .
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN
EN 13852-3:2021(Main)
Cranes - Offshore cranes - Part 3: Light offshore cranes
SIST EN 13852-3:2021

This document applies to light offshore cranes including their supporting pedestals and structures.
NOTE   Supporting pedestal and structures such as columns and boom rests, are covered by this document to the extent where their main purpose is to support the crane.
This document is applicable to light offshore cranes, whose structures are made of steel, and fulfil all of the following characteristics:
-   maximum rated capacity 15 tonnes or maximum static load moment 3 000 kNm;
-   limitation for off-board lifting operation up to Hs = 2,0 m and wind speed 15 m/s (3 s gust);
-   maximum number of working cycles class U1 (C ≤ 3,15 × 104) according to EN 13001-1.
This document provides requirements for all significant hazards, hazardous situations and events relevant to light offshore cranes for lifting of goods and lifting of persons, when used as intended and under conditions foreseen by the risk assessment (see Clause 4).
This document is applicable to light offshore cranes, which are manufactured after the date of approval by CEN of this document.
This document is not applicable for:
a)   transportation, assembly, disabling, scrapping, installation or erecting of the crane;
b)   any item attached to the hook, such as loads, non-fixed load lifting attachments, lifting accessories, baskets, carriers and containers;
c)   lifting operations in ambient temperatures below −20 °C;
d)   lifting operations in ambient temperatures above 45 °C;
e)   lifting operations involving more than one crane;
f)   accidental loads as result of collisions, earthquakes, explosions, etc., which are not covered by exceptional loads defined in Table B.7;
g)   emergency personnel rescue operations (except training);
h)   subsea lifting operations;
i)   general purpose offshore cranes (covered by EN 13852-1), floating cranes and motion compensated cranes.

  • Standard
    111 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 13852-1:2013(Main)
Cranes - Offshore cranes - Part 1: General-purpose offshore cranes
SIST EN 13852-1:2013

This European Standard specifies the requirements for general-purpose offshore cranes including their supporting pedestals or structures.
The standard is applicable to general-purpose offshore cranes covered by the scope of this European Standard which are manufactured after the date of its publication as EN.
This European Standard is not applicable to general-purpose offshore cranes which are manufactured before the date of its publication as an EN.
This European Standard does not cover use of - or hazards relating to the following:
a)   fabrication, transportation, assembly, dismantling, disabling, scrapping or changing the configuration of the crane;
b)   lifting accessories, i.e. any item between the hook and the load;
c)   minimum design temperature below −20 °C;
d)   operations at an ambient temperature above 45 °C;
NOTE:   For equipment designed for operation in explosive atmospheres, the normal ambient temperature range is −20 °C to +40 °C, unless otherwise specified and marked. See Annex O and relevant standards indicated for complete information.
e)   lifting operations involving more than one crane;
f)   accidental loads due to collisions;
g)   hand powered cranes and other cranes with a rated capacity less than 2 t or outreach less than 8 m;
h)   emergency rescue operations; (except training)
i)   subsea lifting operations.
The significant hazards covered by this European standard are identified in Clause 4.
This European Standard includes requirements for the lifting of personnel by a general-purpose offshore crane.

  • Standard
    96 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
prEN 13852-1(Main)
Cranes - Offshore cranes - Part 1: General-purpose offshore cranes
oSIST prEN 13852-1:2021

This document applies to general purpose offshore cranes including their supporting pedestals and structures.
This document is applicable to general purpose offshore cranes, whose structures are made of steel.
This document provides requirements for all significant hazards, hazardous situations and events relevant to general purpose offshore cranes, for lifting of goods and lifting of persons, when used as intended and under the conditions foreseen by the risk assessment (see Clause 4).
This document is applicable to general purpose offshore cranes, which are manufactured after the date of approval by CEN of this document.
This document is not applicable for:
a)   transportation, assembly, disabling, scrapping, installation or erecting of the crane;
b)   any item attached to the hook, such as loads, non-fixed load lifting attachments, lifting accessories, baskets, carriers and containers;
c)   lifting operations in ambient temperatures below - 20 °C;
d)   lifting operations in ambient temperatures above 45 °C;
e)   accidental loads as result of collisions, earthquakes, explosions, etc., which are not covered by exceptional loads defined in Table B.7 ;
f)   floating cranes (covered by EN13852-2), light offshore cranes (covered by FprEN13852-3) and 2D/3D motion compensated cranes;
g)   subsea lifting operations;
h)   lifting operations involving more than one crane;
i)   emergency rescue operations (except training).

  • Draft
    139 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 13852-3:2021(Main)
Cranes - Offshore cranes - Part 3: Light offshore cranes
SIST EN 13852-3:2021

This document applies to light offshore cranes including their supporting pedestals and structures.
NOTE   Supporting pedestal and structures such as columns and boom rests, are covered by this document to the extent where their main purpose is to support the crane.
This document is applicable to light offshore cranes, whose structures are made of steel, and fulfil all of the following characteristics:
-   maximum rated capacity 15 tonnes or maximum static load moment 3 000 kNm;
-   limitation for off-board lifting operation up to Hs = 2,0 m and wind speed 15 m/s (3 s gust);
-   maximum number of working cycles class U1 (C ≤ 3,15 × 104) according to EN 13001-1.
This document provides requirements for all significant hazards, hazardous situations and events relevant to light offshore cranes for lifting of goods and lifting of persons, when used as intended and under conditions foreseen by the risk assessment (see Clause 4).
This document is applicable to light offshore cranes, which are manufactured after the date of approval by CEN of this document.
This document is not applicable for:
a)   transportation, assembly, disabling, scrapping, installation or erecting of the crane;
b)   any item attached to the hook, such as loads, non-fixed load lifting attachments, lifting accessories, baskets, carriers and containers;
c)   lifting operations in ambient temperatures below −20 °C;
d)   lifting operations in ambient temperatures above 45 °C;
e)   lifting operations involving more than one crane;
f)   accidental loads as result of collisions, earthquakes, explosions, etc., which are not covered by exceptional loads defined in Table B.7;
g)   emergency personnel rescue operations (except training);
h)   subsea lifting operations;
i)   general purpose offshore cranes (covered by EN 13852-1), floating cranes and motion compensated cranes.

  • Standard
    111 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 13852-1:2013(Main)
Cranes - Offshore cranes - Part 1: General-purpose offshore cranes
SIST EN 13852-1:2013

This European Standard specifies the requirements for general-purpose offshore cranes including their supporting pedestals or structures.
The standard is applicable to general-purpose offshore cranes covered by the scope of this European Standard which are manufactured after the date of its publication as EN.
This European Standard is not applicable to general-purpose offshore cranes which are manufactured before the date of its publication as an EN.
This European Standard does not cover use of - or hazards relating to the following:
a)   fabrication, transportation, assembly, dismantling, disabling, scrapping or changing the configuration of the crane;
b)   lifting accessories, i.e. any item between the hook and the load;
c)   minimum design temperature below −20 °C;
d)   operations at an ambient temperature above 45 °C;
NOTE:   For equipment designed for operation in explosive atmospheres, the normal ambient temperature range is −20 °C to +40 °C, unless otherwise specified and marked. See Annex O and relevant standards indicated for complete information.
e)   lifting operations involving more than one crane;
f)   accidental loads due to collisions;
g)   hand powered cranes and other cranes with a rated capacity less than 2 t or outreach less than 8 m;
h)   emergency rescue operations; (except training)
i)   subsea lifting operations.
The significant hazards covered by this European standard are identified in Clause 4.
This European Standard includes requirements for the lifting of personnel by a general-purpose offshore crane.

  • Standard
    96 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
prEN 13852-1(Main)
Cranes - Offshore cranes - Part 1: General-purpose offshore cranes
oSIST prEN 13852-1:2021

This document applies to general purpose offshore cranes including their supporting pedestals and structures.
This document is applicable to general purpose offshore cranes, whose structures are made of steel.
This document provides requirements for all significant hazards, hazardous situations and events relevant to general purpose offshore cranes, for lifting of goods and lifting of persons, when used as intended and under the conditions foreseen by the risk assessment (see Clause 4).
This document is applicable to general purpose offshore cranes, which are manufactured after the date of approval by CEN of this document.
This document is not applicable for:
a)   transportation, assembly, disabling, scrapping, installation or erecting of the crane;
b)   any item attached to the hook, such as loads, non-fixed load lifting attachments, lifting accessories, baskets, carriers and containers;
c)   lifting operations in ambient temperatures below - 20 °C;
d)   lifting operations in ambient temperatures above 45 °C;
e)   accidental loads as result of collisions, earthquakes, explosions, etc., which are not covered by exceptional loads defined in Table B.7 ;
f)   floating cranes (covered by EN13852-2), light offshore cranes (covered by FprEN13852-3) and 2D/3D motion compensated cranes;
g)   subsea lifting operations;
h)   lifting operations involving more than one crane;
i)   emergency rescue operations (except training).

  • Draft
    139 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 16739-1:2024(Main)
Industry Foundation Classes (IFC) for data sharing in the construction and facility management industries - Part 1: Data schema (ISO 16739-1:2024)
kSIST FprEN ISO 16739-1:2024

This document represents an open international standard for information used in Building Information Modeling (BIM) that is exchanged and shared among software applications used by the various participants in the construction or facility management industry sector. This document includes definitions that cover information required for buildings and infrastructure works over their life cycle. This edition of the document added coverage of information required for infrastructure facilities including bridges, roads, railways, waterways and port facilities.
This document comprises the publication of a data schema, its documentation, the property and quantity set definitions and the mechanism of an exchange file format structure.
Definitions from this document are used to support different recognized work flows in the construction and facility management industry sector, representing information deliveries. Such information deliveries can be described according to ISO 29481.
Different implementation levels of this document can be defined to better support multiple information deliveries, they are referred to as a Model View Definition (MVD). Each MVD identifies which subset of the definitions of this document imposes requirements for implementation in software applications. Conforming software applications need to identify the model view definition they conform to when applying for software certification.
The following are within the scope of this edition of this document:
BIM exchange format definitions that are required during the life cycle phases of buildings and infrastructure:
demonstrating the need;
conception of need;
outline feasibility;
substantive feasibility study and outline financial authority;
outline conceptual design;
full conceptual design;
coordinated design;
procurement and full financial authority;
production information;
construction;
operation and maintenance.
BIM exchange format definitions that are required by the various disciplines involved within the life cycle phases:
architecture and civil engineering design;
service and utilities engineering;
structural engineering;
procurement;
construction planning;
facility and utility management;
project management;
client requirement management;
industry authorities for permits and approval.
BIM exchange format definitions including:
project structure;
physical components;
spatial components;
analysis items;
processes;
resources;
controls;
actors;
context definition.

  • Draft
    406 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 17294-1:2024(Main)
Water quality - Application of inductively coupled plasma mass spectrometry (ICP-MS) - Part 1: General requirements (ISO 17294-1:2024)
kSIST FprEN ISO 17294-1:2023

This document specifies the principles of inductively coupled plasma mass spectrometry (ICP-MS) and provides general requirements for the use of this technique to determine elements in water, digests of sludges and sediments (e.g. digests of water as described in ISO 15587-1 or ISO 15587-2). Generally, the measurement is carried out in water, but gases, vapours or fine particulate matter can be introduced too. This document applies to the use of ICP-MS for aqueous solution analysis.
The ultimate determination of the elements is described in a separate International Standard for each series of elements and matrix. The individual clauses of this document refer the user to these guidelines for the basic principles of the method and the configuration of the instrument.

  • Draft
    43 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 22435:2024(Main)
Gas cylinders - Cylinder valves with integrated pressure regulators - Specification and type testing (ISO 22435:2024)
kSIST FprEN ISO 22435:2024

This document specifies design, type test methods, marking and instruction requirements for cylinder valves with integrated pressure regulators (VIPRs) intended to be fitted to gas cylinders, pressure drums or tubes or used as a main valve for bundles of cylinders that convey compressed, liquefied or dissolved gases.
These are requirements for VIPRs that are in addition to those given in the relevant closure standard, for example, in ISO 10297 for cylinder valves, in ISO 17871 for quick-release cylinder valves, in ISO 17879 for self-closing cylinder valves or in ISO 23826 for ball valves. For ISO 17871, these requirements are only applicable to quick-release cylinder valves types B, C, D and E.
NOTE 1        If the pressure regulating system of a VIPR is acting as the primary valve operating mechanism, it is covered by the relevant closure standard, e.g. ISO 10297, ISO 17871, ISO 17879 and ISO 23826. This also includes designs where closure of the primary valve operating mechanism of a VIPR is obtained by closing the seat of the pressure regulating system.
NOTE 2        If the primary valve operating mechanism of a VIPR is located at the low-pressure side of the pressure regulating system, it is covered by the relevant closure standard, e.g. ISO 10297, ISO 17871, ISO 17879 and ISO 23826.
NOTE 3        The term “pressure receptacle” is used within this document to cover instances where no differentiation is necessary between gas cylinders, bundles of cylinders, pressure drums and tubes.
This document does not apply to VIPRs for
a)       medical applications (see ISO 10524-3);
b)       liquefied petroleum gas (LPG);
c)        cryogenic applications.
NOTE 4        Additional requirements for a VIPR with a residual pressure device (RPD) are specified in ISO 15996.
NOTE 5        Additional requirements for pressure relief valves can exist in international/regional regulations/ standards.

  • Draft
    39 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 683-2:2024(Main)
Aluminium and aluminium alloys - Finstock - Part 2: Mechanical properties
kSIST FprEN 683-2:2024

This document specifies the mechanical properties of wrought aluminium and wrought aluminium alloy finstock.
The chemical composition limits of these materials are specified in EN 573 3, unless otherwise agreed between supplier and purchaser.
The designations of wrought aluminium and wrought aluminium alloys and the temper designations used in this document are specified in EN 573 3, and the temper designations are defined in EN 515.

  • Draft
    12 pages
    English language
    sale 10% off
    e-Library read for
    1 day