Aerospace series - Inserts, thin wall, self-locking - Installation and removal procedure

This standard specifies the conditions of installation and removal (hole serration profile, tools, swaging procedure) of self-locking thin wall inserts defined by EN standards, for aerospace applications.

Luft- und Raumfahrt - Gewindeeinsätze, dünnwandig, selbstsichernd - Ein- und Ausbauverfahren

Série aérospatiale - Douilles filetées, à paroi mince, à freinage interne - Procédure d'installation et d'extraction

Aeronavtika - Vložki, tanka stena, samozapiralni - Postopek namestitve in odstranitve

General Information

Status
Withdrawn
Publication Date
05-May-2008
Withdrawal Date
26-May-2024
Technical Committee
Current Stage
9900 - Withdrawal (Adopted Project)
Start Date
27-May-2024
Due Date
19-Jun-2024
Completion Date
27-May-2024

Relations

Buy Standard

Standard
EN 3298:2008
English language
16 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Aerospace series - Inserts, thin wall, self-locking - Installation and removal procedureAeronavtika - Vložki, tanka stena, samozapiralni - Postopek namestitve in odstranitveSérie aérospatiale - Douilles filetées, à paroi mince, à freinage interne - Procédure d'installation et d'extractionLuft- und Raumfahrt - Gewindeeinsätze, dünnwandig, selbstsichernd - Ein- und Ausbauverfahren49.030.30MaticeNutsICS:SIST EN 3298:2008enTa slovenski standard je istoveten z:EN 3298:200801-julij-2008SIST EN 3298:2008SLOVENSKI
STANDARDSIST EN 3298:20011DGRPHãþD







EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 3298April 2008ICS 49.030.30Supersedes EN 3298:1998
English VersionAerospace series - Inserts, thin wall, self-locking - Installationand removal procedureSérie aérospatiale - Douilles filetées, à paroi mince, àfreinage interne - Procédure d'installation et d'extractionLuft- und Raumfahrt - Gewindeeinsätze, dünnwandig,selbstsichernd - Ein- und AusbauverfahrenThis European Standard was approved by CEN on 5 January 2008.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the CEN Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as theofficial versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2008 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 3298:2008: E



EN 3298:2008 (E) 2 Contents Page Foreword.3 1 Scope.4 2 Normative references.4 3 Hole serration profile (short inserts).4 4 Installation of inserts.5 5 Minimum criteria for the installation and removal tools and their methods of application.5 6 Assembly tools and gauges.6 6.1 General.6 6.2 Installation drive tool.6 6.3 Swage tools.7 7 Installation procedure.8 7.1 Insertion.8 7.2 Insert alignment prior to swaging.8 7.3 Swaging.9 7.4 After swage inspection.10 7.5 Inspection for minimum locking torque.11 8 Insert removal and replacement.12 Annex A (informative)
Recommended toolin
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.