CEN/TC 256/SC 2/WG 12 - Roller bearings and Lubricants

This European Standard specifies the quality parameters of axlebox rolling bearings supporting the load of the vehicle, required for reliable operation of trains on European networks. It covers metallurgical and material properties as well as geometric and dimensional characteristics. It also defines methods for quality assurance and conditions for approval of the products.

This European Standard specifies the principles and methods for a rig performance test of the system of axlebox rolling bearing(s), housing, seal(s) and grease. Test parameters and minimum performance requirements for vehicles in operation on main lines are specified. Different test parameters and performance requirements may be selected for vehicles in operation on other networks (e.g. urban rail). This standard is historically developed for outboard applications but can be used for vehicles with other bearing arrangements (e.g.: inboard application or single wheels).
It gives some possible examples where a "sequenced performance test" addresses the broad range of different service conditions within a specific application or vehicle platform into account.
It describes in detail the water tightness test and basic principles and minimum requirements for a field test.
This European Standard only applies to axleboxes equipped with rolling bearings and greases according to EN 12080 and EN 12081.

This European Standard specifies the quality requirements of greases intended for the lubrication of axlebox rolling bearings according to prEN 12080, required for reliable operation of trains on European networks. It covers the approval procedure for a not yet approved grease, the management of modification for an approved grease and the method of quality batch control of the grease. The grease requirements are given for two speed classes.

This European Standard specifies a testing method and sets the acceptance criteria for the determining of the lubrication ability of lubricating greases intended for the lubrication of axlebox bearings. The lubricating ability, primarily related to the capability of lubricating greases to protect against wear, is determined in a roller bearing lubricant test rig. Wear of the rolling bearing rollers, the frictional behaviour and temperature during the test are used to discriminate between lubricating greases.
NOTE 1   The testing method is referred to in EN 12081.
The method described is carried out in order to test axlebox greases for ordinary-speed vehicles, with speeds up to 200 km/h, and for greases intended for high-speed vehicles, with speeds up to 300 km/h. The method is a discriminating process, and those greases that pass will be subject to more extensive performance tests.
NOTE 2   In EN 12082 a more extensive rig performance test is described in detail. This rig performance test will check the satisfactory function of the assembly of box housing, bearing, sealing and grease during a simulated journey.
For purpose of quality assurance and quality control, this test method is also used for batch testing of greases intended for use in axleboxes.
For light rail and tramway applications other standards or documents agreed between the customer and the supplier may be applied.

This European Standard specifies a test method and sets the acceptance criteria for the determination of the mechanical stability of lubricating greases intended for the lubrication of axlebox bearings according to EN 12081. In the test, impacts are applied to the lubricating grease so that only very stable lubricating greases will perform acceptably. The method is used in a discrimination process for finding lubricating greases of such mechanical stability that they are considered accepted lubricating greases for more extensive performance tests according to EN 12082.
For purposes of quality assurance and quality control, this test method is also used for batch testing of lubricating greases.

Revised Annex ZA

Revised Annex ZA

This European Standard specifies the quality parameters of axlebox rolling bearings supporting the load of the vehicle, required for reliable operation of trains on European networks. It covers metallurgical and material properties as well as geometric and dimensional characteristics. It also defines methods for quality assurance and conditions for approval of the products.

This European Standard specifies the principles and methods for a rig performance test of the system of axlebox rolling bearing(s), housing, seal(s) and grease. Test parameters and minimum performance requirements for vehicles in operation on main lines are specified. Different test parameters and performance requirements may be selected for vehicles in operation on other networks (e.g. urban rail). This standard is historically developed for outboard applications but can be used for vehicles with other bearing arrangements (e.g.: inboard application or single wheels).
It gives some possible examples where a "sequenced performance test" addresses the broad range of different service conditions within a specific application or vehicle platform into account.
It describes in detail the water tightness test and basic principles and minimum requirements for a field test.
This European Standard only applies to axleboxes equipped with rolling bearings and greases according to EN 12080 and EN 12081.

This European Standard specifies the quality requirements of greases intended for the lubrication of axlebox rolling bearings according to EN 12080, required for reliable operation of trains on European networks. It covers the approval procedure, the method of quality control and quality monitoring of the grease. The grease requirements are given for two speed classes.

This European Standard specifies a testing method and sets the acceptance criteria for the determining of the lubrication ability of lubricating greases intended for the lubrication of axlebox bearings. The lubricating ability, primarily related to the capability of lubricating greases to protect against wear, is determined in a roller bearing lubricant test rig. Wear of the rolling bearing rollers, the frictional behaviour and temperature during the test are used to discriminate between lubricating greases.
NOTE 1   The testing method is referred to in EN 12081.
The method described is carried out in order to test axlebox greases for ordinary-speed vehicles, with speeds up to 200 km/h, and for greases intended for high-speed vehicles, with speeds up to 300 km/h. The method is a discriminating process, and those greases that pass will be subject to more extensive performance tests.
NOTE 2   In EN 12082 a more extensive rig performance test is described in detail. This rig performance test will check the satisfactory function of the assembly of box housing, bearing, sealing and grease during a simulated journey.
For purpose of quality assurance and quality control, this test method is also used for batch testing of greases intended for use in axleboxes.
For light rail and tramway applications other standards or documents agreed between the customer and the supplier may be applied.

This European Standard specifies the quality requirements of greases intended for the lubrication of axlebox rolling bearings according to EN 12080, required for reliable operation of trains on European networks. It covers the approval procedure, the method of quality control and quality monitoring of the grease. The grease requirements are given for two speed classes.

This European Standard specifies the quality parameters of axlebox rolling bearings, required for reliable operation of trains on European networks. It covers metallurgical and material properties as well as geometric and dimensional characteristics. It also defines methods for quality assurance and conditions for approval of the products.

This European Standard specifies a test method and sets the acceptance criteria for the determination of the mechanical stability of lubricating greases intended for the lubrication of axlebox bearings according to EN 12081. In the test, impacts are applied to the lubricating grease so that only very stable lubricating greases will perform acceptably. The method is used in a discrimination process for finding lubricating greases of such mechanical stability that they are considered accepted lubricating greases for more extensive performance tests according to EN 12082.
For purposes of quality assurance and quality control, this test method is also used for batch testing of lubricating greases.

This European Standard specifies the quality parameters of axlebox rolling bearings supporting the load of the vehicle, required for reliable operation of trains on European networks. It covers metallurgical and material properties as well as geometric and dimensional characteristics. It also defines methods for quality assurance and conditions for approval of the products.

This European Standard specifies the principles and methods for a rig performance test of the system of axlebox rolling bearing(s), housing, seal(s) and grease. Test parameters and minimum performance requirements for vehicles in operation on main lines are specified. Different test parameters and performance requirements may be selected for vehicles in operation on other networks (e.g. urban rail). This standard is historically developed for outboard applications but can be used for vehicles with other bearing arrangements (e.g.: inboard application or single wheels).
It gives some possible examples where a "sequenced performance test" addresses the broad range of different service conditions within a specific application or vehicle platform into account.
It describes in detail the water tightness test and basic principles and minimum requirements for a field test.
This European Standard only applies to axleboxes equipped with rolling bearings and greases according to EN 12080 and EN 12081.

This European Standard specifies the quality requirements of greases intended for the lubrication of axlebox rolling bearings according to EN 12080, required for reliable operation of trains on European networks. It covers the approval procedure, the method of quality control and quality monitoring of the grease. The grease requirements are given for two speed classes.

This European Standard specifies the quality parameters of axlebox rolling bearings, required for reliable operation of trains on European networks. It covers metallurgical and material properties as well as geometric and dimensional characteristics. It also defines methods for quality assurance and conditions for approval of the products.

This European Standard specifies the principles and methods for a rig performance test of the system of box housing, rolling bearings, sealing and grease. Test parameters and minimum performance requirements for vehicles in operation on main lines are specified in Clause 6 and Annex A (normative). Different test parameters and performance requirements may be selected for vehicles in operation on other networks.
Basic principles for a field test are also determined.

This European Standard specifies a test method and sets the acceptance criteria for the determination of the mechanical stability of lubricating greases intended for the lubrication of axlebox bearings according to EN 12081. In the test, impacts are applied to the lubricating grease so that only very stable lubricating greases will perform acceptably. The method is used in a discrimination process for finding lubricating greases of such mechanical stability that they are considered accepted lubricating greases for more extensive performance tests according to EN 12082.
For purposes of quality assurance and quality control, this test method is also used for batch testing of lubricating greases.

This European Standard specifies a testing method and sets the acceptance criteria for the determining of the lubrication ability of lubricating greases intended for the lubrication of axlebox bearings. The lubricating ability, primarily related to the capability of lubricating greases to protect against wear, is determined in a roller bearing lubricant test rig. Wear of the rolling bearing rollers, the frictional behaviour and temperature during the test are used to discriminate between lubricating greases.
NOTE 1   The testing method is referred to in EN 12081.
The method described is carried out in order to test axlebox greases for ordinary-speed vehicles, with speeds up to 200 km/h, and for greases intended for high-speed vehicles, with speeds up to 300 km/h. The method is a discriminating process, and those greases that pass will be subject to more extensive performance tests.
NOTE 2   In EN 12082 a more extensive rig performance test is described in detail. This rig performance test will check the satisfactory function of the assembly of box housing, bearing, sealing and grease during a simulated journey.
For purpose of quality assurance and quality control, this test method is also used for batch testing of greases intended for use in axleboxes.
For light rail and tramway applications other standards or documents agreed between the customer and the supplier may be applied.

This European Standard specifies the quality requirements of greases intended for the lubrication of axlebox rolling bearings according to EN 12080, required for reliable operation of trains on European networks. It covers the approval procedure, the method of quality control and quality monitoring of the grease. The grease requirements are given for two speed classes.

This European Standard specifies the principles and methods for a rig performance test of the system of box housing, rolling bearings, sealing and grease. Test parameters and minimum performance requirements for vehicles in operation on main lines are specified in Clause 6 and Annex A (normative). Different test parameters and performance requirements may be selected for vehicles in operation on other networks.
Basic principles for a field test are also determined.

This European Standard specifies the quality parameters of axlebox rolling bearings, required for reliable operation of trains on European networks. It covers metallurgical and material properties as well as geometric and dimensional characteristics. It also defines methods for quality assurance and conditions for approval of the products.

This European Standard specifies a test method and sets the acceptance criteria for the determination of the mechanical stability of lubricating greases intended for the lubrication of axlebox bearings according to EN 12081. In the test, impacts are applied to the lubricating grease so that only very stable lubricating greases will perform acceptably. The method is used in a discrimination process for finding lubricating greases of such mechanical stability that they are considered accepted lubricating greases for more extensive performance tests according to EN 12082.
For purposes of quality assurance and quality control, this test method is also used for batch testing of lubricating greases.

This European Standard describes the principles and methods for a rig performance test of assembled axleboxes with rolling bearings according to EN 12080 and with lubricating greases according to EN 12081. Test parameters and minimum performance requirements for vehicles in operation on main lines are specified in clause 6 and Annex A (normative). Different test parameters and performance requirements may be selected for vehicles in operation on other networks. Basic principles for a field test are also determined.

This European Standard defines the quality parameters of axlebox rolling bearings, required for reliable operation of trains on European networks. It covers metallurgical and material properties as well as geometric and dimensional characteristics. It also defines methods for quality assurance and conditions for approval of the products.

This European Standard defines the quality requirements of greases intended for the lubrication of axlebox rolling bearings according to EN 12080, required for reliable operation of trains on European networks. It covers the approval procedure, the method of quality control and quality monitoring of the grease. The grease requirements are given for two speed classes.