ECISS/TC 110/WG 3 - Fittings

This document specifies the technical delivery requirements for seamless and welded butt welding fittings (elbows, concentric and eccentric reducers, equal and reducing tees, caps) made of carbon and alloy steel in two test categories which are intended for pressure purposes at room temperature, at low temperature or at elevated temperatures, and for the transmission and distribution of fluids and gases.
It specifies:
a)   type of fittings;
type A: Butt-welding fittings with reduced pressure factor;
type B: Butt-welding fittings for use at full service pressure;
b)   steel grades and their chemical compositions;
c)   mechanical properties;
d)   dimensions and tolerances;
e)   requirements for inspection and testing;
f)   inspection documents;
g)   marking;
h)   protection and packaging.
NOTE   The selection of the appropriate fitting (material, thickness) is the ultimate responsibility of the manufacturer of the pressure equipment (see European Legislation for Pressure Equipment). In the case of a harmonized supporting standard for materials, presumption of conformity to the ESRs is limited to technical data of materials in the standard and does not presume adequacy of the material to a specific item of equipment. Consequently, it is essential that the technical data stated in the material standard be assessed against the design requirements of this specific item of equipment to verify that the ESRs of the PED are satisfied.

This document specifies the requirements for the design, performance and testing of fittings made of malleable cast iron (see also Clause 5 Materials) with compression ends for polyethylene piping systems.
This document applies to piping systems in polyethylene (PE) materials for different application fields, such as water and gas supply, water distribution, irrigation, aqueous liquids, pressurized air and gaseous fuel systems.
NOTE   Products complying with this document used for water applications intended for human consumption are expected to comply with the relevant national, regional or local regulatory provisions applicable in the place of use. Due to the variety and dynamic of the requirements, it is advisable to check the compliance.
The malleable cast iron fittings specified in this standard are of compression end type for the connection of PE pipes or of transition type with combined compression ends for pipes in different materials or with combined compression and threaded ends in conformance with EN 10226-1. Their range of sizes covers nominal outside diameters of PE pipes dn 16 mm to dn 110 mm (DN 10 to DN 100) and pipe thread sizes ⅜ to 4.

This document specifies the requirements for the design and performance of threaded pipe fittings in malleable cast iron with black or hot dip galvanized surface.
These fittings are for general purposes for the transmission of fluids and gases up to the limits of operating pressure and operating temperature specified in this document. They are intended for the connection of elements threaded with sizes ⅛ to 6 (DN 6 to DN 150).
Fittings with alternative permanent coatings or permanent coatings on top of hot dip galvanizing do not fall under the scope of this document.
NOTE   One main use is for the connection of non-alloy steel tubes according to EN 10255 and with support of the thread joint by using sealing materials according to the EN 751 series.

This document specifies the technical delivery requirements for seamless and welded butt-welding fittings (elbows, concentric and eccentric reducers, equal and reducing tees, caps) made of austenitic and austenitic-ferritic (duplex) stainless steel in two test-categories which are intended for pressure purposes at room temperature, at low temperature or at elevated temperatures, and for the transmission and distribution of fluids and gases.
It specifies:
a)   type of fittings;
1)   type A: butt-welding fittings with reduced pressure factor;
2)   type B: butt-welding fittings for use at full service pressure;
b)   steel grades and their chemical compositions;
c)   mechanical properties;
d)   dimensions and tolerances;
e)   requirements for inspection and testing;
f)   inspection documents;
g)   marking;
h)   protection and packaging.
NOTE   The selection of the appropriate fitting (material, thickness) is the ultimate responsibility of the manufacturer of the pressure equipment (see European Legislation for Pressure Equipment). In the case of a harmonized supporting standard for materials, presumption of conformity to the ESRs is limited to technical data of materials in the standard and does not presume adequacy of the material to a specific item of equipment. Consequently, it is essential that the technical data stated in the material standard be assessed against the design requirements of this specific item of equipment to verify that the ESRs of the PED are satisfied.

This standard specifies the requirements for the design, performance and testing of fittings made of malleable cast iron (see also clause 5 Materials) with compression ends for steel pipes. It applies to steel piping systems for different application fields, such as gas supply, distribution of water for general purposes and for human consumption, irrigation, fire fighting, aqueous liquids, compressed air and gaseous fuel systems.
It also applies to oil piping systems, provided the elastomeric sealing material is compatible with the oil and the operating conditions.
It contains requirements and tests relating to compression fittings which can be disconnected from smooth walled steel pipes or other cylindrical metal structural elements, which are applicable for dismantleable joints. The fittings can also incorporate other types of connection, such as threaded, flanged, compression ends for connection of polyethylene pipes, etc., and can also take on various structural shapes, such as, straight piece, elbow or T-piece, etc. Their range of sizes covers nominal sizes DN 6 to DN 100 (size 1/8 to 4).

This standard specifies the requirements for the design, performance and testing of fittings made of malleable cast iron (see also clause 5 Materials) with compression ends for steel pipes. It applies to steel piping systems for different application fields, such as gas supply, distribution of water for general purposes and for human consumption, irrigation, fire fighting, aqueous liquids, compressed air and gaseous fuel systems.
It also applies to oil piping systems, provided the elastomeric sealing material is compatible with the oil and the operating conditions.
It contains requirements and tests relating to compression fittings which can be disconnected from smooth walled steel pipes or other cylindrical metal structural elements, which are applicable for dismantleable joints. The fittings can also incorporate other types of connection, such as threaded, flanged, compression ends for connection of polyethylene pipes, etc., and can also take on various structural shapes, such as, straight piece, elbow or T-piece, etc. Their range of sizes covers nominal sizes DN 6 to DN 100 (size 1/8 to 4).