EN ISO 25178-2:2022

SLOVENSKI STANDARD
SIST EN ISO 25178-2:2022
01-marec-2022
Nadomešča:
SIST EN ISO 25178-2:2012
Specifikacija geometrijskih veličin izdelka (GPS) - Tekstura površine: ploskovna -
2. del: Izrazi, definicije in parametri teksture površine (ISO 25178-2:2021)
Geometrical product specifications (GPS) - Surface texture: Areal - Part 2: Terms,
definitions and surface texture parameters (ISO 25178-2:2021)
Geometrische Produktspezifikation (GPS) - Oberflächenbeschaffenheit: Flächenhaft -
Teil 2: Begriffe, Definitionen und Oberflächen-Kenngrößen (ISO 25178-2:2021)
Spécification géométrique des produits (GPS) - État de surface: Surfacique - Partie 2:
Termes, définitions et paramètres d'états de surface (ISO 25178-2:2021)
Ta slovenski standard je istoveten z: EN ISO 25178-2:2022
ICS:
17.040.20 Lastnosti površin Properties of surfaces
17.040.40 Specifikacija geometrijskih Geometrical Product
veličin izdelka (GPS) Specification (GPS)
SIST EN ISO 25178-2:2022 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN ISO 25178-2:2022

---------------------- Page: 2 ----------------------
SIST EN ISO 25178-2:2022


EN ISO 25178-2
EUROPEAN STANDARD

NORME EUROPÉENNE

January 2022
EUROPÄISCHE NORM
ICS 17.040.20 Supersedes EN ISO 25178-2:2012
English Version

Geometrical product specifications (GPS) - Surface texture:
Areal - Part 2: Terms, definitions and surface texture
parameters (ISO 25178-2:2021)
Spécification géométrique des produits (GPS) - État de Geometrische Produktspezifikation (GPS) -
surface: Surfacique - Partie 2: Termes, définitions et Oberflächenbeschaffenheit: Flächenhaft - Teil 2:
paramètres d'états de surface (ISO 25178-2:2021) Begriffe, Definitionen und Oberflächen-Kenngrößen
(ISO 25178-2:2021)
This European Standard was approved by CEN on 27 November 2021.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2022 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 25178-2:2022 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------
SIST EN ISO 25178-2:2022
EN ISO 25178-2:2022 (E)
Contents Page
European foreword . 3

2

---------------------- Page: 4 ----------------------
SIST EN ISO 25178-2:2022
EN ISO 25178-2:2022 (E)
European foreword
This document (EN ISO 25178-2:2022) has been prepared by Technical Committee ISO/TC 213
"Dimensional and geometrical product specifications and verification" in collaboration with Technical
Committee CEN/TC 290 “Dimensional and geometrical product specification and verification” the
secretariat of which is held by AFNOR.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by July 2022, and conflicting national standards shall be
withdrawn at the latest by July 2022.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 25178-2:2012.
Any feedback and questions on this document should be directed to the users’ national standards
body/national committee. A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Cro
...