iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
IEC

IEC 61034-2:2005

(Main)

Measurement of smoke density of cables burning under defined conditions - Part 2: Test procedure and requirements

Measurement of smoke density of cables burning under defined conditions - Part 2: Test procedure and requirements

Provides details of the test procedure to be employed for the measurement of the density of smoke emitted from cables burning under defined conditions. It describes the means of preparing and assembling cables for test, the method of burning the cables, and gives recommended requirements for evaluating test results. The principal changes with respect to the previous edition are as follows: a) inclusion of cables down to 1 mm diameter; b) inclusion of non-circular cables; c) addition of guidance on testing cables above 80 mm diameter; d) delineation of elements of the test report; e) addition of guidance on the calculation for other parameters for fire safety engineering purposes; f) removal of minor differences with equivalent CENELEC work to allow parallel voting with that body. Has the status of a group safety publication in accordance with IEC Guide 104. The contents of the corrigendum of September 2006 have been included in this copy.

Mesure de la densité de fumées dégagées par des câbles brûlant dans des conditions définies - Partie 2: Procédure d'essai et exigences

Fournit des détails de la procédure d'essai à employer pour la mesure de la densité des fumées émises par des câbles brûlant dans des conditions définies. Elle décrit les méthodes de préparation et d'assemblage des câbles en essais, la méthode d'inflammation des câbles, et donne des recommandations pour les exigences relatives à l'évaluation des résultats d'essais. Les principales modifications par rapport à l'édition précédente sont: a) l'introduction des câbles de diamètre allant jusqu' à 1 mm; b) l'introduction des câbles non circulaires; c) l'addition d'un guide sur les essais de câbles de diamètre supérieur à 80 mm; d) la suppression d'éléments du rapport d'essai; e) l'ajout d'un guide pour le calcul d'autres paramètres pour la conception de sécurité incendie; f) la suppression des petites différences par rapport aux travaux équivalents du CENELEC pour un vote parallèle. Elle a le statut de publication groupée de sécurité, conformément au Guide 104 de la CEI. Le contenu du corrigendum de septembre 2006 a été pris en considération dans cet exemplaire.

General Information

Status
Published
Publication Date
26-Jun-2013
ICS
13.220.40 - Ignitability and burning behaviour of materials and products
29.020 - Electrical engineering in general
29.060.20 - Cables
Technical Committee
TC 20 - Electric cables
Drafting Committee
WG 18 - TC 20/WG 18
Current Stage
PPUB - Publication issued
Start Date
15-Aug-2005
Completion Date
20-Apr-2005
Ref Project

Relations

Amended By
IEC 61034-2:2005/AMD1:2013 - Amendment 1 - Measurement of smoke density of cables burning under defined conditions - Part 2: Test procedure and requirements
Effective Date
05-Sep-2023
Amended By
IEC 61034-2:2005/AMD2:2019 - Amendment 2 - Measurement of smoke density of cables burning under defined conditions - Part 2: Test procedure and requirements
Effective Date
05-Sep-2023

Buy Standard

IEC 61034-2:2005 - Measurement of smoke density of cables burning under defined conditions - Part 2: Test procedure and requirementsIEC 61034-2:2005 - Measurement of smoke density of cables burning under defined conditions - Part 2: Test procedure and requirements
PreviousNext
Standard
IEC 61034-2:2005 - Measurement of smoke density of cables burning under defined conditions - Part 2: Test procedure and requirements
English and French language
31 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

NORME CEI
INTERNATIONALE
IEC



61034-2
INTERNATIONAL


Troisième édition
STANDARD

Third edition
2005-04

PUBLICATION GROUPÉE DE SÉCURITÉ
GROUP SAFETY PUBLICATION
Mesure de la densité de fumées
dégagées par des câbles brûlant
dans des conditions définies –
Partie 2:
Procédure d'essai et exigences

Measurement of smoke density of cables
burning under defined conditions –
Part 2:
Test procedure and requirements
Numéro de référence
Reference number
CEI/IEC 61034-2:2005

---------------------- Page: 1 ----------------------
Numérotation des publications Publication numbering
Depuis le 1er janvier 1997, les publications de la CEI As from 1 January 1997 all IEC publications are
sont numérotées à partir de 60000. Ainsi, la CEI 34-1 issued with a designation in the 60000 series. For
devient la CEI 60034-1. example, IEC 34-1 is now referred to as IEC 60034-1.
Editions consolidées Consolidated editions
Les versions consolidées de certaines publications de la The IEC is now publishing consolidated versions of its
CEI incorporant les amendements sont disponibles. Par publications. For example, edition numbers 1.0, 1.1
exemple, les numéros d’édition 1.0, 1.1 et 1.2 indiquent and 1.2 refer, respectively, to the base publication,
respectivement la publication de base, la publication de the base publication incorporating amendment 1 and
base incorporant l’amendement 1, et la publication de the base publication incorporating amendments 1
base incorporant les amendements 1 et 2. and 2.
Informations supplémentaires Further information on IEC publications
sur les publications de la CEI
Le contenu technique des publications de la CEI est The technical content of IEC publications is kept
constamment revu par la CEI afin qu'il reflète l'état under constant review by the IEC, thus ensuring that
actuel de la technique. Des renseignements relatifs à the content reflects current technology. Information
cette publication, y compris sa validité, sont dispo- relating to this publication, including its validity, is
nibles dans le Catalogue des publications de la CEI available in the IEC Catalogue of publications
(voir ci-dessous) en plus des nouvelles éditions, (see below) in addition to new editions, amendments
amendements et corrigenda. Des informations sur les and corrigenda. Information on the subjects under
sujets à l’étude et l’avancement des travaux entrepris consideration and work in progress undertaken by the
par le comité d’études qui a élaboré cette publication, technical committee which has prepared this
ainsi que la liste des publications parues, sont publication, as well as the list of publications issued,
également disponibles par l’intermédiaire de: is also available from the following:
• Site web de la CEI (www.iec.ch) • IEC Web Site (www.iec.ch)
• Catalogue des publications de la CEI • Catalogue of IEC publications
Le catalogue en ligne sur le site web de la CEI The on-line catalogue on the IEC web site
(www.iec.ch/searchpub) vous permet de faire des (www.iec.ch/searchpub) enables you to search by a
recherches en utilisant de nombreux critères, variety of criteria including text searches,
comprenant des recherches textuelles, par comité technical committees and date of publication. On-
d’études ou date de publication. Des informations en line information is also available on recently
ligne sont également disponibles sur les nouvelles issued publications, withdrawn and replaced
publications, les publications remplacées ou retirées, publications, as well as corrigenda.
ainsi que sur les corrigenda.
• IEC Just Published • IEC Just Published
Ce résumé des dernières publications parues This summary of recently issued publications
(www.iec.ch/online_news/justpub) est aussi dispo- (www.iec.ch/online_news/justpub) is also available
nible par courrier électronique. Veuillez prendre by email. Please contact the Customer Service
contact avec le Service client (voir ci-dessous) Centre (see below) for further information.
pour plus d’informations.
• Service clients • Customer Service Centre
Si vous avez des questions au sujet de cette If you have any questions regarding this
publication ou avez besoin de renseignements publication or need further assistance, please
supplémentaires, prenez contact avec le Service contact the Customer Service Centre:
clients:
Email: custserv@iec.ch Email: custserv@iec.ch
Tél: +41 22 919 02 11 Tel: +41 22 919 02 11
Fax: +41 22 919 03 00 Fax: +41 22 919 03 00
.

---------------------- Page: 2 ----------------------
NORME CEI
INTERNATIONALE
IEC



61034-2
INTERNATIONAL


Troisième édition
STANDARD

Third edition

2005-04


PUBLICATION GROUPÉE DE SÉCURITÉ
GROUP SAFETY PUBLICATION
Mesure de la densité de fumées
dégagées par des câbles brûlant
dans des conditions définies –
Partie 2:
Procédure d'essai et exigences

Measurement of smoke density of cables
burning under defined conditions –
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

IEC
IEC 60754-1:2011/AMD1:2019(Amendment)
Amendment 1 - Test on gases evolved during combustion of materials from cables - Part 1: Determination of the halogen acid gas content
  • Standard
    12 pages
    English and French language
    sale 15% off
IEC
IEC 60754-2:2011/AMD1:2019(Amendment)
Amendment 1 - Test on gases evolved during combustion of materials from cables - Part 2: Determination of acidity (by pH measurement) and conductivity
  • Standard
    13 pages
    English and French language
    sale 15% off
IEC
IEC 61034-1:2005/AMD2:2019(Amendment)
Amendment 2 - Measurement of smoke density of cables burning under defined conditions - Part 1: Test apparatus
  • Standard
    5 pages
    English and French language
    sale 15% off
IEC
IEC 61034-2:2005/AMD2:2019(Amendment)
Amendment 2 - Measurement of smoke density of cables burning under defined conditions - Part 2: Test procedure and requirements
  • Standard
    5 pages
    English and French language
    sale 15% off
IEC
IEC 60331-3:2018(Main)
Tests for electric cables under fire conditions - Circuit integrity - Part 3: Test method for fire with shock at a temperature of at least 830 °C for cables of rated voltage up to and including 0,6/1,0 kV tested in a metal enclosure

IEC 60331-3:2018 is available as IEC 60331-3:2018 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.
IEC 60331-3:2018 specifies the test method for cables which are required to maintain circuit integrity when tested in a metal enclosure and when subject to fire and mechanical shock under specified conditions. This document is applicable to cables of rated voltage not exceeding 600 V/1 000 V, including those of rated voltage below 80 V, metallic data and telecom cables and optical fibre cables. It is intended for use when testing cables not greater than 20 mm overall diameter. This document includes details for the specific point of failure, continuity checking arrangement, test sample, test procedure and test report relevant to electric power and control cables with rated voltage up to and including 600 V/1 000 V. Details for the specific point of failure, continuity checking arrangement, test sample, test procedure and test report relevant to metallic data and telecom cables and optical fibre cables are not given by IEC 60331-3. Although the scope is restricted to cables with rated voltage up to and including 0,6/1,0 kV, the procedure can be used, with the agreement of the manufacturer and the purchaser, for cables with rated voltage up to and including 1,8/3 (3,3) kV, provided that suitable fuses are used. It is not assumed that cables successfully assessed by this method, will also pass requirements for either IEC 60331-1 or IEC 60331-2. Testing to either of these two standards is to be carried out separately. Such additional performance can be recognised by the marking in accordance with IEC 60331-1:2018 Clause 11 or IEC 60331 2:2018 Clause 11. This second edition cancels and replaces the first edition published in 2009. It constitutes a technical revision. The significant technical changes with respect to the previous edition are as follows:
– extension of the scope to include metallic data and telecom cables and optical fibre cables, although details for the specific point of failure, continuity checking arrangement, test sample, test procedure and test report relevant to metallic data and telecom cables and optical fibre cables are not given by IEC 60331-3;
– improved description of the test environment;
– mandatory use of mass flow meter/controllers as the means of controlling accurately the input flow rates of fuel and air to the burner;
– improved description of the information to be included in the test report.

  • Standard
    52 pages
    English and French language
    sale 15% off
IEC
IEC 60331-2:2018(Main)
Tests for electric cables under fire conditions - Circuit integrity - Part 2: Test method for fire with shock at a temperature of at least 830 °C for cables of rated voltage up to and including 0,6/1,0 kV and with an overall diameter not exceeding 20 mm

IEC 60331-2:2018 specifies the test method for cables which are required to maintain circuit integrity when subject to fire and mechanical shock under specified conditions.
This document is applicable to cables of rated voltage not exceeding 600 V/1 000 V, including those of rated voltage below 80 V, metallic data and telecom cables and optical fibre cables.
It is intended for use when testing cables of not greater than 20 mm overall diameter.
Cables of larger diameter are intended to be tested using the apparatus, procedure and requirements of IEC 60331-1.
This document includes details for the specific point of failure, continuity checking arrangement, test sample, test procedure and test report relevant to electric power and control cables with rated voltage up to and including 600 V/1000 V. Details for the specific point of failure, continuity checking arrangement, test sample, test procedure and test report relevant to metallic data and telecom cables and optical fibre cables are not given by IEC 60331-2.
Although the scope is restricted to cables with rated voltage up to and including 0,6/1,0 kV, the procedure can be used, with the agreement of the manufacturer and the purchaser, for cables with rated voltage up to and including 1,8/3 (3,3) kV, provided that suitable fuses are used.
Annex A provides the method of verification of the burner and control system used for the test.
Requirements are stated for an identification that may optionally be marked on the cable to signify compliance with this standard.
This second edition cancels and replaces the first edition published in 2009. It constitutes a technical revision.
The significant technical changes with respect to the previous edition are as follows:
– extension of the scope with metallic data and telecom cables and optical fibre cables, although details for the specific point of failure, continuity checking arrangement, test sample, test procedure and test report relevant to metallicdata and telecom cables and optical fibre cables are not given by IEC 60331-2;
– improved description of the test environment;
– mandatory use of mass flow meters/controllers as the means of controlling accurately the input flow rates of fuel and air to the burner;
– improved figure illustrating method of mounting of the sample regarding bending radius;
– improved description of the information to be included in the test report.

  • Standard
    50 pages
    English and French language
    sale 15% off
IEC
IEC 60331-1:2018(Main)
Tests for electric cables under fire conditions - Circuit integrity - Part 1: Test method for fire with shock at a temperature of at least 830 °C for cables of rated voltage up to and including 0,6/1,0 kV and with an overall diameter exceeding 20 mm

IEC 60331-1:2018 specifies the test method for cables which are required to maintain circuit integrity when subject to fire and mechanical shock under specified conditions.
This document is applicable to cables of rated voltage not exceeding 600 V/1 000 V, including those of rated voltage below 80 V, metallic data and telecom cables and optical fibre cables.
It is intended for use when testing cables of greater than 20 mm overall diameter.
Cables of smaller diameter are intended to be tested using the apparatus, procedure and requirements of IEC 60331-2.
This document includes details for the specific point of failure, continuity checking arrangement, test sample, test procedure and test report relevant to electric power and control cables with rated voltage up to and including 600 V/1 000 V. Details for the specific point of failure, continuity checking arrangement, test sample, test procedure and test report relevant to metallic data and telecom cables and optical fibre cables are not given by IEC 60331-1.
Although the scope is restricted to cables with rated voltage up to and including 0,6/1,0 kV, the procedure can be used, with the agreement of the manufacturer and the purchaser, for cables with rated voltage up to and including 1,8/3 (3,3) kV, provided that suitable fuses are used.
Annex A provides the method of verification of the burner and control system used for the test.
Requirements are stated for an identification that may optionally be marked on the cable to signify compliance with this document.
This second edition cancels and replaces the first edition published in 2009. It constitutes a technical revision.
The significant technical changes with respect to the previous edition are as follows:
– extension of the scope to include metallic data and telecom cables and optical fibre cables, although details for the specific point of failure, continuity checking arrangement, test sample, test procedure and test report relevant to metallic data and telecom cables and optical fibre cables are not given by IEC 60331-1;
– improved description of the test environment;
– modified steel test ladder with two extra vertical elements to accommodate the modified testing of single core cables without concentric metal layer and the testing of cables with a bending radius in normal use larger than approximately 400 mm;
– mandatory use of mass flow meters/controllers as the means of controlling accurately the input flow rates of fuel and air to the burner;
– improved description of the information to be included in the test report.
This document has the status of a group safety publication in accordance with IEC Guide 104.

  • Standard
    55 pages
    English and French language
    sale 15% off
IEC
IEC 60332-1-1:2004/AMD1:2015(Amendment)
Amendment 1 - Tests on electric and optical fibre cables under fire conditions - Part 1-1: Test for vertical flame propagation for a single insulated wire or cable - Apparatus
  • Standard
    5 pages
    English and French language
    sale 15% off
IEC
IEC 60332-1-3:2004(Main)
Tests on electric and optical fibre cables under fire conditions - Part 1-3: Test for vertical flame propagation for a single insulated wire or cable - Procedure for determination of flaming droplets/particles

IEC 60332-1-3:2004 Specifies a test procedure for assessment of falling flaming droplets/ particles when a single vertical electrical insulated conductor or cable, or optical fibre cable, is subjected to defined fire conditions. NOTE - Testing to IEC 60332-1-3 may be performed simultaneously with that to IEC 60332-1-2, if required. Recommended requirements for performance are given in Annex A. IEC 60332-1-3 specifies the use of a 1 kW pre-mixed flame and is for general use, except that the procedure specified may not be suitable for the testing of small single insulated conductors or cables of less than 0,5 mm2 total cross-section because the conductor melts before the test is completed, or for the testing of small optical fibre cables because the cable is broken before the test is completed.

  • Standard
    21 pages
    English and French language
    sale 15% off
IEC
IEC 60332-1-1:2004(Main)
Tests on electric and optical fibre cables under fire conditions - Part 1-1: Test for vertical flame propagation for a single insulated wire or cable - Apparatus

IEC 60332-1-1:2004 Specifies the test apparatus for testing the resistance to vertical flame propagation for a single vertical electrical insulated conductor or cable, or optical fibre cable, under fire conditions. The procedure, together with an informative annex of recommended requirements for performance, is given in IEC 60332-1-2.

  • Standard
    15 pages
    English and French language
    sale 15% off